Date: Wed, 30 Jul 2008 19:45:21 -0300 From: JoaoBR <joao@matik.com.br> To: freebsd-drivers@freebsd.org Cc: ikram@wideband.com.pk, Sam Leffler <sam@freebsd.org> Subject: Re: Incorrect Atheros txpower output Message-ID: <200807301945.22284.joao@matik.com.br> In-Reply-To: <488F7FE1.5080401@freebsd.org> References: <6fe7c62a0807291226x15ef59bcn334c97562f3399b8@mail.gmail.com> <20080729.142220.-749250939.imp@bsdimp.com> <488F7FE1.5080401@freebsd.org>
next in thread | previous in thread | raw e-mail | index | archive | help
On Tuesday 29 July 2008 17:38:57 Sam Leffler wrote:
> M. Warner Losh wrote:
> > In message: <6fe7c62a0807291226x15ef59bcn334c97562f3399b8@mail.gmail.co=
m>
> >
> > "Mohammad Ikram" <ikram@wideband.com.pk> writes:
> > : Hi !
> > :
> > : I am using FreeBSD 7.0 and recently installed a Engines EPI-3601S car=
d.
> > : The card has an Atheros chip with a 27dBm output power rating. I am
> > : using it as hostap. FreeBSD detects it fine, but the trouble is FreeB=
SD
> > : does not takes the power level up. The max i was able to set is was
> > : 16dBm. (ifconfig ath0 txpower xx). I tried it on linux with madwifi b=
ut
> > : same results, so i started having a few doubts with this card, a frie=
nd
> > : of mine suggested that i should try the router OS (www.mikrotik.com) i
> > : did, and it worked perfectly.
> > :
> > : can any one tell me why can't i change the power level ? (i did chang=
ed
> > : country codes, to no avail) i read some where it is the problem with
> > : the driver ? so is there any patch ?
> >
> > Did you measure the output power directly? Many cards have a final
> > stage amplifier that kicks things up a few dB... Maybe router OS
> > knows about this card's quirks and copes...
>
> The external PA's you're thinking of are not controllable by the host;
> they are always present. The original post doesn't explain how mikrotik
> "worked perfectly" while freebsd did not. I have measured many high
> power cards with a power meter and SA under FreeBSD and have never seen
> a power cap other than that imposed by regulatory or vendor mis-claims.
>
certainly the poster has reason here, follows an ifconfig from a machine wi=
th=20
a DLINK AG530 (ath1) which has 60mW I think and a genius 400mW card (ath0),=
=20
both show with same power values
but clients connected to each card (and switching them between both ssid) s=
how=20
that they get a far better RSSI on the stronger card, something about 20-25%
also on client site you can see a clearly stronger signal what on a FreeBSD=
=20
ath client shows up with 30% more RSSI when connected to the 400mW
I do not believe that this card really has 400mW, if then the signal or RSS=
I=20
should be far stronger but is not, I compare to a test I run with an 0.5W=20
amplifier I sticked onto the Dlink card which than gives a really signal=20
boost
I also have no comparism to other OS with this cards and I am not so worrie=
d=20
about what ifconfig tells because at the end the signal is stronger
I use this ath_hal: 0.10.5.6 but the former hal gave same results
ath0: flags=3D8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0=
mtu=20
1500
ether 00:02:6f:4a:a6:29
media: IEEE 802.11 Wireless Ethernet DS/11Mbps mode 11b <hostap>
status: associated
ssid LUCENET-CW channel 6 (2437 Mhz 11b) bssid 00:02:6f:4a:a6:29
wepkey 4:40-bit powersavemode OFF powersavesleep 100 txpower 31.5
txpowmax 18.0 rtsthreshold 2346 fragthreshold 2346 bmiss 7
scanvalid 60 bgscan bgscanintvl 300 bgscanidle 250 roam:rssi11a 7
roam:rate11a 12 roam:rssi11b 7 roam:rate11b 1 roam:rssi11g 7
roam:rate11g 5 -pureg protmode CTS -ht -htcompat -ampdu ampdulimit =
8k
ampdudensity - -amsdu -shortgi htprotmode RTSCTS -puren -wme burst =
=2Dff
-dturbo hidessid -apbridge dtimperiod 1 doth inact bintval 100
ath1: flags=3D8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0=
mtu=20
1500
ether 00:19:5b:cf:26:78
media: IEEE 802.11 Wireless Ethernet DS/11Mbps mode 11b <hostap>
status: associated
ssid LUCENET-CS channel 1 (2412 Mhz 11b) bssid 00:19:5b:cf:26:78
wepkey 4:40-bit powersavemode OFF powersavesleep 100 txpower 31.5
txpowmax 18.0 rtsthreshold 2346 fragthreshold 2346 bmiss 7
scanvalid 60 bgscan bgscanintvl 300 bgscanidle 250 roam:rssi11a 7
roam:rate11a 12 roam:rssi11b 7 roam:rate11b 1 roam:rssi11g 7
roam:rate11g 5 -pureg protmode CTS -ht -htcompat -ampdu ampdulimit =
8k
ampdudensity - -amsdu -shortgi htprotmode RTSCTS -puren -wme burst =
=2Dff
-dturbo hidessid -apbridge dtimperiod 1 doth inact bintval 100
=2D-=20
Jo=E3o
A mensagem foi scaneada pelo sistema de e-mail e pode ser considerada segura.
Service fornecido pelo Datacenter Matik https://datacenter.matik.com.br
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200807301945.22284.joao>