Date: Tue, 4 Feb 2003 22:40:09 +0100 From: Flag_reda <p.pisati@oltrelinux.com> To: FreeBSD_Current <freebsd-current@FreeBSD.ORG> Subject: Re: 5.0 on IBM T30: X11 failure Message-ID: <20030204214009.GA1587@southcross.skynet.org> In-Reply-To: <20030204193809.GA31148@troutmask.apl.washington.edu> References: <200302041858.h14Iw4hK006869@castle.org> <20030204193809.GA31148@troutmask.apl.washington.edu>
next in thread | previous in thread | raw e-mail | index | archive | help
On Tue, Feb 04, 2003 at 11:38:09AM -0800, Steve Kargl wrote:
> On Tue, Feb 04, 2003 at 10:58:04AM -0800, Lee Damon wrote:
> > (II) ATI: Candidate "Device" section "Card0".
> > (--) Chipset ATI Radeon Mobility LW (AGP) found
>
> There are known problems with the ATI Radeon Mobility
> driver. I had to compile X11 from the cvs repository
> at www.xfree86.org to get my labtop working. The
> problem should be fixed when XFree86 4.3 is released.
I'm using a 5.0, an Inteli815 chipser, XFree 4.2.1 (from ports) and
an ATI Radeon Mobility and it works perfectly... no problem!
Well, actually there's alway that memory corruption problem related to
agp: if someone want to know some more i can provide information.
anyway, this is my dmesg:
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #4: Tue Feb 4 17:40:56 CET 2003
flag@southcross.skynet.org:/usr/obj/usr/src/sys/SOUTHCROSS
Preloaded elf kernel "/boot/kernel/kernel" at 0xc04af000.
Preloaded elf module "/boot/kernel/snd_maestro3.ko" at 0xc04af0a8.
Preloaded elf module "/boot/kernel/snd_pcm.ko" at 0xc04af15c.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc04af208.
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 1135913540 Hz
CPU: Intel(R) Pentium(R) III CPU 1133MHz (1135.91-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6b1 Stepping = 1
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 268353536 (255 MB)
avail memory = 255598592 (243 MB)
Initializing GEOMetry subsystem
netsmb_dev: loaded
Pentium Pro MTRR support enabled
VESA: v2.0, 16384k memory, flags:0x1, mode table:0xc03c46a2 (1000022)
VESA: ATI MOBILITY RADEON
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <ASUS L8L > on motherboard
ACPI-0625: *** Info: GPE Block0 defined as GPE0 to GPE15
ACPI-0625: *** Info: GPE Block1 defined as GPE16 to GPE31
Using $PIR table, 6 entries at 0xc00f1a70
acpi0: power button is handled as a fixed feature programming model.
Timecounter "ACPI-fast" frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0xe408-0xe40b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_acad0: <AC adapter> on acpi0
acpi_cmbat0: <Control method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcm0: <ESS Technology Allegro-1> port 0xb800-0xb8ff irq 5 at device 1.0 on pci2
pcm0: <ESS Technology ES1921 ac97 codec>
pci2: <simple comms> at device 1.1 (no driver attached)
rl0: <RealTek 8139 10/100BaseTX> port 0xb000-0xb0ff mem 0xee800000-0xee8000ff irq 9 at device 3.0 on pci2
rl0: Realtek 8139B detected. Warning, this may be unstable in autoselect mode
rl0: Ethernet address: 00:e0:18:2d:26:b0
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
cbb0: <RF5C476 PCI-CardBus Bridge> irq 11 at device 5.0 on pci2
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb1: <RF5C476 PCI-CardBus Bridge> irq 11 at device 5.1 on pci2
cbb1: Could not map register memory
device_probe_and_attach: cbb1 attach returned 12
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH2 ATA100 controller> port 0xa800-0xa80f at device 31.1 on pci0
atapci0: ATA channel disabled by BIOS
uhci0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> port 0xa400-0xa41f irq 9 at device 31.2 on pci0
usb0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ums0: Logitech USB Mouse, rev 1.10/6.20, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
acpi_button1: <Sleep Button> on acpi0
speaker0 port 0x61 on acpi0
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
orm0: <Option ROM> at iomem 0xc0000-0xcefff on isa0
ata0 at port 0x3f6,0x1f0-0x1f7 irq 14 on isa0
ata1 at port 0x376,0x170-0x177 irq 15 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0 at vga0
Timecounters tick every 10.000 msec
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
ACPI-1287: *** Error: Method execution failed, AE_AML_UNINITIALIZED_ELEMENT
ad0: 38154MB <FUJITSU MHS2040AT> [77520/16/63] at ata0-master BIOSPIO
acd0: DVD-ROM <TOSHIBA DVD-ROM SD-C2502> at ata0-slave BIOSPIO
Mounting root from ufs:/dev/ad0s1a
as u can see i've a problem with ACPI, and i DON'T load the
agp module, causa i don't want to crash the system.
(agp module => memory corruption => spontaneous crash&reboot at least
this for my hw).
Hope this help.
--
Paolo
Italian FreeBSD User Group: http://www.gufi.org
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20030204214009.GA1587>