Date: Wed, 14 Aug 2019 20:33:04 +0200 From: =?utf-8?Q?S=C3=B8ren_Schmidt?= <soren.schmidt@gmail.com> To: Mit Matelske <mit@pt.net> Cc: Marcin Wojtas <mw@semihalf.com>, freebsd-arm <freebsd-arm@freebsd.org> Subject: Re: Espressobin anyone ? Message-ID: <0E42E605-477E-4E65-810E-BD3A8CDE2C80@gmail.com> In-Reply-To: <1547777156.662147.1565798461515.JavaMail.zimbra@perftech.com> References: <E73AFF5D-43CA-41A7-BDBA-ADEF2D342479@deepcore.dk> <1634814667.34671.1565644485029.JavaMail.zimbra@perftech.com> <CAPv3WKeMEe9mW8YYS8k=J9obwde9KEidMHHQpPJ0idrhcyx=RQ@mail.gmail.com> <45CD194B-8533-42B7-9FE8-B2C8C03F4422@gmail.com> <1021311926.304550.1565731831094.JavaMail.zimbra@perftech.com> <4AE7C7A2-0BFB-4093-AE19-6AAC8F44FF25@gmail.com> <917479365.631712.1565792953255.JavaMail.zimbra@perftech.com> <CAPv3WKeCRWy65LPeeJiisPtaz=LePpVYLDAi2cj%2B2TQR=r09YA@mail.gmail.com> <1547777156.662147.1565798461515.JavaMail.zimbra@perftech.com>
next in thread | previous in thread | raw e-mail | index | archive | help
[-- Attachment #1 --]
It might simply be broken in -current (again).
I just updated my stable12 tree and I pulled in new .dts files for just about anything…
Needless to say, it broke the Espressobin’s SD support, it now fails just like yours..
It also broke allwinner builds and what not, so I’m just going back in time again :)
I wonder why there is this overwhelming need to import stuff that breaks things right, left and center in a -stable branch ?
That would have earned you the pointy hat back when….
-Søren
> On 14 Aug 2019, at 18.01, Mit Matelske <mit@pt.net> wrote:
>
> Marcin-
>
> Sorry I didn't reply yesterday. I didn't have any luck with that either. I tried a lot of permutations.
>
> Not saying for 100% it doesn't work, but I couldn't get it to work!
>
> Mit
>
> From: "Marcin Wojtas" <mw@semihalf.com>
> To: "Mit Matelske" <mit@pt.net>
> Cc: "Søren Schmidt" <soren.schmidt@gmail.com>, "freebsd-arm" <freebsd-arm@freebsd.org>
> Sent: Wednesday, August 14, 2019 10:41:04 AM
> Subject: Re: Espressobin anyone ?
>
> Hi Mit,
> Since you are using the latest 13-current, could you please try if passing rootdev via u-boot bootargs (please see my previous email) works for you without the loader modification?
>
> Best regards,
> Marcin
>
> śr., 14 sie 2019 o 16:29 Mit Matelske <mit@pt.net <mailto:mit@pt.net>> napisał(a):
> Soren-
>
> Thanks for the info. I'll grab a couple more SD cards at lunch. This one is a new Samsung 32GB. I'll also try putting the changes into 12 and see if that helps. I'm using the latest 13-current.
>
> Again, appreciate the hand holding!
>
> Mit
>
> From: "Søren Schmidt" <soren.schmidt@gmail.com <mailto:soren.schmidt@gmail.com>>
> To: "Mit Matelske" <mit@pt.net <mailto:mit@pt.net>>
> Cc: "Marcin Wojtas" <mw@semihalf.com <mailto:mw@semihalf.com>>, "freebsd-arm" <freebsd-arm@freebsd.org <mailto:freebsd-arm@freebsd.org>>
> Sent: Wednesday, August 14, 2019 2:30:31 AM
> Subject: Re: Espressobin anyone ?
>
> Hi Mit
> Hmm, from your earlier posted dmesgs it looks like the SD card is not getting detected properly..
>
> I get this output:
>
> sdhci_xenon0: <Armada Xenon SDHCI controller> mem 0xd0000-0xd02ff,0x1e808-0x1e80b irq 24 on simplebus1
> mmc0: <MMC/SD bus> on sdhci_xenon0
> …snip…
> mmcsd0: 16GB <SDHC SD16G 3.0 SN 01E28E67 MFG 07/2017 by 39 PH> at mmc0 50.0MHz/4bit/65535-block
>
> The problem you see was fixed for me by r348882, maybe it got broken later, I havn’t backported the later changes..
>
> Have you tried another SD card ? I have found 2 of mine that the espressobin doesn’t like, but works fine with bananapi and friends...
>
> -Søren
>
> On 13 Aug 2019, at 23.30, Mit Matelske <mit@pt.net <mailto:mit@pt.net>> wrote:
>
> Soren-
>
> Thanks for the code snippet! That will fix one of the problems.
>
> I still can't mount my filesystem, though. I think I'm doing something really simple, wrong. I believe I'm running the latest code and added some printfs to show the kernel setting the regulator:
>
>
> usbus1 on ehci0
> syscon_generic4: <syscon> mem 0x5f800-0x5ffff on simplebus1
> sdhci_xenon0: regulator_get_by_ofw_property(vqmmc-supply) = 19
> sdhci_xenon0: vqmmc-supply regulator found
> sdhci_xenon0: <Armada Xenon SDHCI controller> mem 0xd0000-0xd02ff,0x1e808-0x1e80b irq 24 on simplebus1
> ahci0: <AHCI SATA controller> mem 0xe0000-0xe0177 irq 26 on simplebus1
>
>
> Could there be a problem with how I am setting up my filesystem? I've tried both freebsd-ufs and freebsd as the type, with no luck. A gpart listing of my SD card:
>
> root@fbl:~ # gpart list da3
> Geom name: da3
> modified: false
> state: OK
> fwheads: 255
> fwsectors: 63
> last: 62521335
> first: 3
> entries: 4
> scheme: GPT
> Providers:
> 1. Name: da3p1
> Mediasize: 41943040 (40M)
> Sectorsize: 512
> Stripesize: 0
> Stripeoffset: 1536
> Mode: r0w0e0
> efimedia: HD(1,GPT,19894dc5-b8b2-11e9-871f-08008a0010e0,0x3,0x14000)
> rawuuid: 19894dc5-b8b2-11e9-871f-08008a0010e0
> rawtype: c12a7328-f81f-11d2-ba4b-00a0c93ec93b
> label: (null)
> length: 41943040
> offset: 1536
> type: efi
> index: 1
> end: 81922
> start: 3
> 2. Name: da3p2
> Mediasize: 31968979456 (30G)
> Sectorsize: 512
> Stripesize: 0
> Stripeoffset: 41944576
> Mode: r0w0e0
> efimedia: HD(2,GPT,98786462-be30-11e9-ae6e-08008a0010e0,0x14003,0x3b8bff5)
> rawuuid: 98786462-be30-11e9-ae6e-08008a0010e0
> rawtype: 516e7cb6-6ecf-11d6-8ff8-00022d09712b
> label: (null)
> length: 31968979456
> offset: 41944576
> type: freebsd-ufs
> index: 2
> end: 62521335
> start: 81923
> Consumers:
> 1. Name: da3
> Mediasize: 32010928128 (30G)
> Sectorsize: 512
> Mode: r0w0e0
>
> Thanks!!
>
> Mit
>
> From: "Søren Schmidt" <soren.schmidt@gmail.com <mailto:soren.schmidt@gmail.com>>
> To: "Marcin Wojtas" <mw@semihalf.com <mailto:mw@semihalf.com>>
> Cc: "Mit Matelske" <mit@pt.net <mailto:mit@pt.net>>, "freebsd-arm" <freebsd-arm@freebsd.org <mailto:freebsd-arm@freebsd.org>>
> Sent: Tuesday, August 13, 2019 12:55:09 PM
> Subject: Re: Espressobin anyone ?
>
> Hi
> That doesn’t seen to work on the espressobin, or least I can’t get it to pick it up.
>
> I use this patch as a workaround:
>
> Index: main.c
> ===================================================================
> --- main.c (revision 350496)
> +++ main.c (working copy)
> @@ -463,6 +462,13 @@
> int rv;
> char *rootdev;
>
> +#if defined(__aarch64__)
> + /* SOS HACK in rootdev, at least Espressobin gets this wrong */
> + printf("Setting currdev hack\n");
> + set_currdev("disk0p2");
> + return (0);
> +#endif
> +
> /*
> * First choice: if rootdev is already set, use that, even if
> * it's wrong.
>
> Its not pretty but it does the job until I get time to look into why bootargs aren’t passed / won’t stick, probably something I havn’t backported to my -stable12 sources yet...
>
> -Søren
>
> On 13 Aug 2019, at 01.38, Marcin Wojtas <mw@semihalf.com <mailto:mw@semihalf.com>> wrote:
>
> Hi,
>
> Not sure if it's what you are looking for, but in order to autoboot, I
> simply pass 'rootdev=diskXpY' in the bootargs variable. Here's example from
> A3720-DB (same should work on EspressoBin):
>
> Marvell>> set bootargs "rootdev=disk1p1";usb reset; fatload usb 0:1
> ${fdt_addr} armada-3720-db.dtb; fatload usb 0:1 ${kernel_addr}
> boot/loader.efi; bootefi ${kernel_addr} ${fdt_addr}
> resetting USB...
> USB0: Register 2000104 NbrPorts 2
> Starting the controller
> USB XHCI 1.00
> USB1: USB EHCI 1.00
> - ______ ____ _____ _____
> | ____| | _ \ / ____| __ \
> | |___ _ __ ___ ___ | |_) | (___ | | | |
> | ___| '__/ _ \/ _ \| _ < \___ \| | | |
> | | | | | __/ __/| |_) |____) | |__| |
> | | | | | | || | | |
> |_| |_| \___|\___||____/|_____/|_____/
> ```
> `
> ╔═══════════Welcome to FreeBSD════════════╗ s` `.....---.......--.```
> -/
> ║ ║ +o .--` /y:`
> +.
> ║ 1. Boot Multi user [Enter] ║ yo`:. :o
> `+-
> ║ 2. Boot Single user ║ y/ -/` -o/
> ║ 3. Escape to loader prompt ║ .-
> ::/sy+:.
> ║ 4. Reboot ║ / `--
> /
> ║ ║ `:
> :`
> ║ Options: ║ `:
> :`
> ║ 5. Kernel: default/kernel (1 of 1) ║ /
> /
> ║ 6. Boot Options ║ .-
> -.
> ║ ║ -- -.
> ║ ║ `:` `:`
> ║ ║ .-- `--.
> ╚═════════════════════════════════════════╝ .---.....----.
> Autoboot in 9 seconds, hit [Enter] to boot or any other key to stop
>
> Loading kernel...
> /boot/kernel/kernel text=0x95047c data=0x1919d0+0x84aa94
> syms=[0x8+0x13aaa8+0x8+0x12610d]
> Loading configured modules...
> can't find '/boot/entropy'
> Using DTB provided by EFI at 0x8000000.
> ---<<BOOT>>---
> KDB: debugger backends: ddb
> KDB: current backend: ddb
> Copyright (c) 1992-2019 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 13.0-CURRENT 17a1fc80d57-c261519(upstream_master) GENERIC arm64
> FreeBSD clang version 8.0.0 (tags/RELEASE_800/final 356365) (based on LLVM
> 8.0.0)
> WARNING: WITNESS option enabled, expect reduced performance.
> VT: init without driver.
> Starting CPU 1 (1)
> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
> [...]
>
> Best regards,
> Marcin
>
> pon., 12 sie 2019 o 23:14 Mit Matelske <mit@pt.net <mailto:mit@pt.net>> napisał(a):
>
>
> Soren-
>
> Thanks for the quick response. I built this kernel with revision 350924.
> I'll dig into whats going on in the morning.
>
> Mind posting your diff for your loader.efi?
>
> Thanks again!
>
> Mit
>
>
> ----- Original Message -----
> From: "Søren Schmidt" <soren.schmidt@gmail.com <mailto:soren.schmidt@gmail.com>>
> To: "Mit Matelske" <mit@pt.net <mailto:mit@pt.net>>
> Cc: "tscho" <johannes@t-beutel.com <mailto:johannes@t-beutel.com>>, "freebsd-arm" <
> freebsd-arm@freebsd.org <mailto:freebsd-arm@freebsd.org>>
> Sent: Monday, August 12, 2019 3:49:48 PM
> Subject: Re: Espressobin anyone ?
>
> Hi
>
> Looks like your sources may be too old, you need to be at least at r348882
> to get the fix for the SD card VCC regulator.
>
> That change fixed it for me backported to 12-stable...
>
> The currdev problem still exists, I have it hardwired in my loader for
> aarch64 :)
>
> -Søren
>
>
> On 12 Aug 2019, at 21.06, Mit Matelske <mit@pt.net <mailto:mit@pt.net>> wrote:
>
> I'm having a couple little hiccups booting this board also. One has
> been commented on already, that I can't get the loader to automatically
> start loading the kernel on "disk0p2"...
>
> The second, is that the kernel can't find the SD card after booting so
> it can't mount the root filesystem. I'm using the dts/dtb and kernel from
> the 13-current branch.
>
> Thanks for any and all help. I haven't used u-boot in about decade.
> Spoiled by the x86 platform.
>
> Mit Matelske
>
>
> ***U-boot environment:***
>
>
> Marvell>> printenv
> baudrate=115200
> bootargs=console=ttyMV0,115200 earlycon=ar3700_uart,0xd0012000
> root=/dev/mmcblk0p1 rw rootwait net.ifnames=0 biosdevname=0
> bootcmd=mmc dev 0; fatload mmc 0:1 $kernel_addr $image_name;fatload mmc
> 0:1 $fdt_addr $fdt_name; bootefi $kernel_addr $fdt_addr
> bootdelay=2
> bootmmc=mmc dev 0; fatload mmc 0:1 $kernel_addr $image_name;fatload mmc
> 0:1 $fdt_addr $fdt_name; bootefi $kernel_addr $fdt_addr
> console=console=ttyMV0,115200 earlycon=ar3700_uart,0xd0012000
> eth1addr=00:51:82:11:22:01
> eth2addr=00:51:82:11:22:02
> eth3addr=00:51:82:11:22:03
> ethact=neta@30000
> ethaddr=F0:AD:4E:09:6B:8F
> ethprime=eth0
> fdt_addr=0x4f00000
> fdt_high=0xffffffffffffffff
> fdt_name=efi/boot/armada-3720-espressobin.dtb
> fdtcontroladdr=3f7161b8
> gatewayip=10.4.50.254
> get_images=tftpboot $kernel_addr $image_name; tftpboot $fdt_addr
> $fdt_name; run get_ramfs
> get_ramfs=if test "${ramfs_name}" != "-"; then setenv ramfs_addr
> 0x8000000; tftpboot $ramfs_addr $ramfs_name; else setenv ramfs_addr -;fi
> hostname=marvell
> image_name=efi/freebsd/loader.efi
> initrd_addr=0xa00000
> initrd_size=0x2000000
> ipaddr=0.0.0.0
> kernel_addr=0x5000000
> loadaddr=0x5000000
> netdev=eth0
> netmask=255.255.255.0
> ramfs_addr=0x8000000
> ramfs_name=-
> root=root=/dev/nfs rw
> rootpath=/srv/nfs/
> serverip=0.0.0.0
> set_bootargs=setenv bootargs $console $root
> ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:none
> nfsroot=$serverip:$rootpath $extra_params
> stderr=serial@12000
> stdin=serial@12000
> stdout=serial@12000
>
>
> ***Full boot logs:***
>
>
> U-Boot 2017.03-armada-17.10.2-g14aeedc (Jun 01 2018 - 15:39:10 +0800)
>
> Model: Marvell Armada 3720 Community Board ESPRESSOBin
> CPU @ 1000 [MHz]
> L2 @ 800 [MHz]
> TClock @ 200 [MHz]
> DDR @ 800 [MHz]
> DRAM: 1 GiB
> U-Boot DT blob at : 000000003f7161b8
> Comphy-0: USB3 5 Gbps
> Comphy-1: PEX0 2.5 Gbps
> Comphy-2: SATA0 6 Gbps
> SATA link 0 timeout.
> AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
> flags: ncq led only pmp fbss pio slum part sxs
> PCIE-0: Link down
> MMC: sdhci@d0000: 0, sdhci@d8000: 1
> SF: Detected mx25u3235f with page size 256 Bytes, erase size 64 KiB,
> total 4 MiB
> Net: eth0: neta@30000 [PRIME]
> Hit any key to stop autoboot: 0
> switch to partitions #0, OK
> mmc0 is current device
> reading efi/freebsd/loader.efi
> 603872 bytes read in 49 ms (11.8 MiB/s)
> reading efi/boot/armada-3720-espressobin.dtb
> 15946 bytes read in 17 ms (916 KiB/s)
> ## Starting EFI application at 05000000 ...
> Scanning disk sdhci@d0000.blk <mailto:sdhci@d0000.blk>...
> Card did not respond to voltage select!
> mmc_init: -95, time 50
> Found 1 disks
> Consoles: EFI console
> FreeBSD/arm64 EFI loader, Revision 1.1
>
> Command line arguments: loader.efi
> EFI version: 2.05
> EFI Firmware: Das U-boot (rev 0.00)
> Console: efi (0)
> Failed to find bootable partition
> Startup error in /boot/lua/loader.lua: seconds
> LUA ERROR: cannot open /boot/lua/loader.lua: invalid argument.
>
> can't load 'kernel'
>
> Type '?' for a list of commands, 'help' for more detailed help.
> OK
> OK set currdev=disk0p2
> OK boot
>
> /boot/kernel/kernel text=0x97d6a0 data=0x191b50+0x84ae94
> syms=[0x8+0x137dd8+0x8+0x126260]
> Using DTB provided by EFI at 0x8000000.
> ---<<BOOT>>---
> KDB: debugger backends: ddb
> KDB: current backend: ddb
> Copyright (c) 1992-2019 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 13.0-CURRENT GENERIC arm64
> FreeBSD clang version 6.0.1 (tags/RELEASE_601/final 335540) (based on
> LLVM 6.0.1)
> WARNING: WITNESS option enabled, expect reduced performance.
> VT: init without driver.
> Starting CPU 1 (1)
> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
> arc4random: WARNING: initial seeding bypassed the cryptographic random
> device because it was not yet seeded and the knob 'bypass_before_seeding'
> was enabled.
> random: entropy device external interface
> MAP 3e681000 mode 2 pages 1
> MAP 3ffa6000 mode 2 pages 1
> kbd0 at kbdmux0
> ofwbus0: <Open Firmware Device Tree>
> simplebus0: <Flattened device tree simple bus> on ofwbus0
> simplebus1: <Flattened device tree simple bus> on simplebus0
> simple_mfd0: <Simple MFD (Multi-Functions Device)> mem
> 0x13800-0x138ff,0x13c00-0x13c1f on simplebus1
> simple_mfd1: <Simple MFD (Multi-Functions Device)> mem
> 0x18800-0x188ff,0x18c00-0x18c1f on simplebus1
> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
> gic0: <ARM Generic Interrupt Controller v3.0> mem
> 0x1d00000-0x1d0ffff,0x1d40000-0x1d7ffff,0x1d80000-0x1d81fff,0x1d90000-0x1d91fff,0x1da0000-0x1dbffff
> irq 27 on simplebus1
> gpio0: <Armada 37x0 North Bridge GPIO Controller> mem
> 0x13800-0x138ff,0x13c00-0x13c1f irq 28,29,30,31,32,33,34,35,36,37,38,39 on
> simple_mfd0
> gpio0: cannot allocate memory window
> device_attach: gpio0 attach returned 6
> gpio0: <Armada 37x0 South Bridge GPIO Controller> mem
> 0x18800-0x188ff,0x18c00-0x18c1f irq 40,41,42,43,44 on simple_mfd1
> gpio0: cannot allocate memory window
> device_attach: gpio0 attach returned 6
> gpioregulator0: <GPIO controlled regulator> on ofwbus0
> gpioregulator0: cannot get pin 0
> gpioregulator0: cannot parse parameters
> device_attach: gpioregulator0 attach returned 6
> generic_timer0: <ARMv8 Generic Timer> irq 0,1,2,3 on ofwbus0
> Timecounter "ARM MPCore Timecounter" frequency 12500000 Hz quality 1000
> Event timer "ARM MPCore Eventtimer" frequency 12500000 Hz quality 1000
> gpio0: <Armada 37x0 North Bridge GPIO Controller> mem
> 0x13800-0x138ff,0x13c00-0x13c1f irq 28,29,30,31,32,33,34,35,36,37,38,39 on
> simple_mfd0
> gpio0: cannot allocate memory window
> device_attach: gpio0 attach returned 6
> gpio0: <Armada 37x0 South Bridge GPIO Controller> mem
> 0x18800-0x188ff,0x18c00-0x18c1f irq 40,41,42,43,44 on simple_mfd1
> gpio0: cannot allocate memory window
> device_attach: gpio0 attach returned 6
> gpioregulator0: <GPIO controlled regulator> on ofwbus0
> gpioregulator0: cannot get pin 0
> gpioregulator0: cannot parse parameters
> device_attach: gpioregulator0 attach returned 6
> gpio0: <Armada 37x0 North Bridge GPIO Controller> mem
> 0x13800-0x138ff,0x13c00-0x13c1f irq 28,29,30,31,32,33,34,35,36,37,38,39 on
> simple_mfd0
> gpio0: cannot allocate memory window
> device_attach: gpio0 attach returned 6
> gpio0: <Armada 37x0 South Bridge GPIO Controller> mem
> 0x18800-0x188ff,0x18c00-0x18c1f irq 40,41,42,43,44 on simple_mfd1
> gpio0: cannot allocate memory window
> device_attach: gpio0 attach returned 6
> gpioregulator0: <GPIO controlled regulator> on ofwbus0
> gpioregulator0: cannot get pin 0
> gpioregulator0: cannot parse parameters
> device_attach: gpioregulator0 attach returned 6
> gpio0: <Armada 37x0 North Bridge GPIO Controller> mem
> 0x13800-0x138ff,0x13c00-0x13c1f irq 28,29,30,31,32,33,34,35,36,37,38,39 on
> simple_mfd0
> gpio0: cannot allocate memory window
> device_attach: gpio0 attach returned 6
> gpio0: <Armada 37x0 South Bridge GPIO Controller> mem
> 0x18800-0x188ff,0x18c00-0x18c1f irq 40,41,42,43,44 on simple_mfd1
> gpio0: cannot allocate memory window
> device_attach: gpio0 attach returned 6
> gpioregulator0: <GPIO controlled regulator> on ofwbus0
> gpioregulator0: cannot get pin 0
> gpioregulator0: cannot parse parameters
> device_attach: gpioregulator0 attach returned 6
> gpio0: <Armada 37x0 North Bridge GPIO Controller> mem
> 0x13800-0x138ff,0x13c00-0x13c1f irq 28,29,30,31,32,33,34,35,36,37,38,39 on
> simple_mfd0
> gpio0: cannot allocate memory window
> device_attach: gpio0 attach returned 6
> gpio0: <Armada 37x0 South Bridge GPIO Controller> mem
> 0x18800-0x188ff,0x18c00-0x18c1f irq 40,41,42,43,44 on simple_mfd1
> gpio0: cannot allocate memory window
> device_attach: gpio0 attach returned 6
> gpioregulator0: <GPIO controlled regulator> on ofwbus0
> gpioregulator0: cannot get pin 0
> gpioregulator0: cannot parse parameters
> device_attach: gpioregulator0 attach returned 6
> cpulist0: <Open Firmware CPU Group> on ofwbus0
> cpu0: <Open Firmware CPU> on cpulist0
> cpu1: <Open Firmware CPU> on cpulist0
> pmu0: <Performance Monitoring Unit> irq 4 on ofwbus0
> syscon_generic0: <syscon> mem 0xd000-0xdfff on simplebus1
> syscon_generic1: <syscon> mem 0x11500-0x1153f on simplebus1
> uart0: <Marvell Armada 3700 UART> mem 0x12000-0x121ff irq 9,10,11 on
> simplebus1
> uart0: console (115200,n,8,1)
> gpio0: <Armada 37x0 North Bridge GPIO Controller> mem
> 0x13800-0x138ff,0x13c00-0x13c1f irq 28,29,30,31,32,33,34,35,36,37,38,39 on
> simple_mfd0
> gpio0: cannot allocate memory window
> device_attach: gpio0 attach returned 6
> syscon_generic2: <syscon> mem 0x14000-0x1405f on simplebus1
> gpio0: <Armada 37x0 South Bridge GPIO Controller> mem
> 0x18800-0x188ff,0x18c00-0x18c1f irq 40,41,42,43,44 on simple_mfd1
> gpio0: cannot allocate memory window
> device_attach: gpio0 attach returned 6
> mvneta0: <NETA controller> mem 0x30000-0x33fff irq 14 on simplebus1
> mvneta0: version is 10
> mvneta0: Ethernet address: 00:a6:39:ca:e8:00
> mdio0: <MDIO> on mvneta0
> mdioproxy0: <MII/MDIO proxy, MDIO side> on mdio0
> e6000sw0: <Marvell 88E6341> on mdio0
> e6000sw0: multi-chip addressing mode (0x1)
> e6000sw0: CPU port at 0
> e6000sw0: fixed port at 0
> e6000sw0: PHY at port 1
> miibus0: <MII bus> on e6000sw0
> e1000phy0: <Marvell 88E1000 Gigabit PHY> PHY 17 on miibus0
> e1000phy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
> 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
> e6000sw0: PHY at port 2
> miibus1: <MII bus> on e6000sw0
> e1000phy1: <Marvell 88E1000 Gigabit PHY> PHY 18 on miibus1
> e1000phy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
> 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
> e6000sw0: PHY at port 3
> miibus2: <MII bus> on e6000sw0
> e1000phy2: <Marvell 88E1000 Gigabit PHY> PHY 19 on miibus2
> e1000phy2: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
> 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
> e6000sw0: switch is ready.
> etherswitch0: <Switch controller> on e6000sw0
> xhci0: <Generic USB 3.0 controller> mem 0x58000-0x5bfff irq 16 on
> simplebus1
> xhci0: 32 bytes context size, 32-bit DMA
> usbus0 on xhci0
> syscon_generic3: <syscon> mem 0x5d800-0x5dfff on simplebus1
> ehci0: <Marvell Integrated USB 2.0 controller> mem 0x5e000-0x5efff irq
> 17 on simplebus1
> usbus1: EHCI version 1.0
> usbus1 on ehci0
> syscon_generic4: <syscon> mem 0x5f800-0x5ffff on simplebus1
> sdhci_xenon0: <Armada Xenon SDHCI controller> mem
> 0xd0000-0xd02ff,0x1e808-0x1e80b irq 24 on simplebus1
> ahci0: <AHCI SATA controller> mem 0xe0000-0xe0177 irq 26 on simplebus1
> ahci0: AHCI v1.30 with 1 6Gbps ports, Port Multiplier supported with FBS
> ahcich0: <AHCI channel> at channel 0 on ahci0
> device_attach: ahcich0 attach returned 6
> gpioregulator0: <GPIO controlled regulator> on ofwbus0
> gpioregulator0: cannot get pin 0
> gpioregulator0: cannot parse parameters
> device_attach: gpioregulator0 attach returned 6
> cryptosoft0: <software crypto>
> Timecounters tick every 1.000 msec
> mvneta0: link state changed to UP
> e6000sw0port1: link state changed to DOWN
> e6000sw0port2: link state changed to DOWN
> e6000sw0port3: link state changed to DOWN
> usbus0: 5.0Gbps Super Speed USB v3.0
> usbus1: 480Mbps High Speed USB v2.0
> Release APs...done
> CPU 0: ARM Cortex-A53 r0p4 affinity: 0
> Instruction Set Attributes 0 = <CRC32,SHA2,SHA1,AES+PMULL>
> Trying to mount root from ufs:/dev/ufs/FreeBSD_Install [ro,noatime]...
> Instruction Set Attributes 1 = <>
> Root mount waiting for: Processor Features 0 =
> <GIC,AdvSIMD,Float,EL3 32,EL2 32,EL1 32,EL0 32>
> usbus1 Processor Features 1 = <0>
> usbus0 Memory Model Features 0 = <4k Granule,64k Granule,S/NS
> Mem,MixedEndian,16bit ASID,1TB PA>
>
> Memory Model Features 1 = <>
> Memory Model Features 2 = <32b CCIDX,48b VA>
> Debug Features 0 = <2 CTX Breakpoints,4 Watchpoints,6
> Breakpoints,PMUv3,Debug v8>
> Debug Features 1 = <0>
> Auxiliary Features 0 = <0>
> Auxiliary Features 1 = <0>
> CPU 1: ARM Cortex-A53 r0p4 affinity: 1
> WARNING: WITNESS option enabled, expect reduced performance.
> ugen0.1: <Generic XHCI root HUB> at usbus0
> ugen1.1: <Marvell EHCI root HUB> at usbus1
> uhub0 on usbus0
> uhub1 on usbus1
> uhub0: <Generic XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on
> usbus0
> uhub1: <Marvell EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on
> usbus1
> uhub0: 2 ports with 2 removable, self powered
> uhub1: 1 port with 1 removable, self powered
> mountroot: waiting for device /dev/ufs/FreeBSD_Install...
> Mounting from ufs:/dev/ufs/FreeBSD_Install failed with error 19.
>
> Loader variables:
> vfs.root.mountfrom=ufs:/dev/ufs/FreeBSD_Install
> vfs.root.mountfrom.options=ro,noatime
>
> Manual root filesystem specification:
> <fstype>:<device> [options]
> Mount <device> using filesystem <fstype>
> and with the specified (optional) option list.
>
> eg. ufs:/dev/da0s1a
> zfs:zroot/ROOT/default
> cd9660:/dev/cd0 ro
> (which is equivalent to: mount -t cd9660 -o ro /dev/cd0 /)
>
> ? List valid disk boot devices
> . Yield 1 second (for background tasks)
> <empty line> Abort manual input
>
> mountroot> ?
>
> List of GEOM managed disk devices:
>
>
> mountroot>
> _______________________________________________
> freebsd-arm@freebsd.org <mailto:freebsd-arm@freebsd.org> mailing list
> https://lists.freebsd.org/mailman/listinfo/freebsd-arm <https://lists.freebsd.org/mailman/listinfo/freebsd-arm>;
> To unsubscribe, send any mail to "freebsd-arm-unsubscribe@freebsd.org <mailto:freebsd-arm-unsubscribe@freebsd.org>"
>
> _______________________________________________
> freebsd-arm@freebsd.org <mailto:freebsd-arm@freebsd.org> mailing list
> https://lists.freebsd.org/mailman/listinfo/freebsd-arm <https://lists.freebsd.org/mailman/listinfo/freebsd-arm>;
> To unsubscribe, send any mail to "freebsd-arm-unsubscribe@freebsd.org <mailto:freebsd-arm-unsubscribe@freebsd.org>"
>
>
>
>
[-- Attachment #2 --]
-----BEGIN PGP SIGNATURE-----
iQIzBAEBCAAdFiEEkC0kEuD0Me2xEj5EGvRMAY4qbRsFAl1UU+AACgkQGvRMAY4q
bRuc4RAAnNRapArBEznLRIMPkZw2Ek8zs5CI8IFawNP7Jh/Ml/bv+rgJ1r8wOIGQ
PGLjl5dqQdw9gQrEQ7UlbMPa2YaGWCQxXAf1TKYEHUGIaSIAAbDCNrSTZCxKw/V0
Hse3a9ctXfPRqbKXz3it1Gd8ky+NQbfyiJaZEckCAC6qCgbIWwMiiyzrVMh60ruw
+2Jg1q7SF67aO1LljMGOoPNViX6uwjxarLMOfc3QcIt7iWLjv98sltuqHuVYMoTS
YcZOUoRSBH+VCMbY/N3cdVMDYWxfHZCyq+ZbzZ9FC6mhb0Q69nP0Qu8rAgFpo286
r+I+oKibdPKsmcWdIuQ0SK9OKT6zoKwXhOfI6T3hWwIAkO5KV7qrTmtabNFnj/Ri
OiKJK6uOyK7lqQeS0Br1b88NzIA72XjYpUShaZZrbfDZcbOn0wFl/f/CIIK/oHwv
AqwQR2DMEMOBO1EF/FCsxzubRWjouqYALnommrZmtAAVx2re7dFTaw4AoQ+5Ud/D
1SwtUuXcxkFkwPxLCkCdJ1SZA9O0D+/3WJDIpbr4Tf0Y32OxAK3Q9UCN3gFNsUzV
mZ2ed84iNzqOWJ18hoM3WJ+WwKKKCcI4DTqpOymcAtGpvcoxbtEHE9PS0I96cpjq
QWBLl3vsi+4rZZnLDK3u/fknpOxGIs8LQodFh5LgQHyf12QLxw8=
=srov
-----END PGP SIGNATURE-----
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?0E42E605-477E-4E65-810E-BD3A8CDE2C80>