Date: Tue, 13 Aug 2019 01:38:58 +0200 From: Marcin Wojtas <mw@semihalf.com> To: Mit Matelske <mit@pt.net> Cc: =?UTF-8?Q?S=C3=B8ren_Schmidt?= <soren.schmidt@gmail.com>, freebsd-arm <freebsd-arm@freebsd.org> Subject: Re: Espressobin anyone ? Message-ID: <CAPv3WKeMEe9mW8YYS8k=J9obwde9KEidMHHQpPJ0idrhcyx=RQ@mail.gmail.com> In-Reply-To: <1634814667.34671.1565644485029.JavaMail.zimbra@perftech.com> References: <E73AFF5D-43CA-41A7-BDBA-ADEF2D342479@deepcore.dk> <CAB=2f8zcYRe0hTkMspgdixy2WFnxBtL1jF1FYBk09A8yb7c3Yw@mail.gmail.com> <44E733F9-5DEB-4A7C-8369-7F6DF2AE03BE@gmail.com> <49A81763-B197-4E66-BA8E-0804C680B842@gmail.com> <1565435583431-0.post@n6.nabble.com> <1F22D8DA-E583-4858-911F-F057EC1A30E0@gmail.com> <532380450.3296650.1565636798211.JavaMail.zimbra@perftech.com> <4A647617-EEC0-4A75-ADF6-3D3F553F9AFF@gmail.com> <1634814667.34671.1565644485029.JavaMail.zimbra@perftech.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Hi,
Not sure if it's what you are looking for, but in order to autoboot, I
simply pass 'rootdev=3DdiskXpY' in the bootargs variable. Here's example fr=
om
A3720-DB (same should work on EspressoBin):
Marvell>> set bootargs "rootdev=3Ddisk1p1";usb reset; fatload usb 0:1
${fdt_addr} armada-3720-db.dtb; fatload usb 0:1 ${kernel_addr}
boot/loader.efi; bootefi ${kernel_addr} ${fdt_addr}
resetting USB...
USB0: Register 2000104 NbrPorts 2
Starting the controller
USB XHCI 1.00
USB1: USB EHCI 1.00
- ______ ____ _____ _____
| ____| | _ \ / ____| __ \
| |___ _ __ ___ ___ | |_) | (___ | | | |
| ___| '__/ _ \/ _ \| _ < \___ \| | | |
| | | | | __/ __/| |_) |____) | |__| |
| | | | | | || | | |
|_| |_| \___|\___||____/|_____/|_____/
```
`
=E2=95=94=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=
=E2=95=90=E2=95=90=E2=95=90=E2=95=90Welcome to FreeBSD=E2=95=90=E2=95=90=E2=
=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=
=90=E2=95=90=E2=95=97 s` `.....---.......--.```
-/
=E2=95=91 =E2=95=91 +o .--` =
/y:`
+.
=E2=95=91 1. Boot Multi user [Enter] =E2=95=91 yo`:. =
:o
`+-
=E2=95=91 2. Boot Single user =E2=95=91 y/ =
-/` -o/
=E2=95=91 3. Escape to loader prompt =E2=95=91 .-
::/sy+:.
=E2=95=91 4. Reboot =E2=95=91 / =
`--
/
=E2=95=91 =E2=95=91 `:
:`
=E2=95=91 Options: =E2=95=91 `:
:`
=E2=95=91 5. Kernel: default/kernel (1 of 1) =E2=95=91 /
/
=E2=95=91 6. Boot Options =E2=95=91 .-
-.
=E2=95=91 =E2=95=91 -- =
-.
=E2=95=91 =E2=95=91 `:` =
`:`
=E2=95=91 =E2=95=91 .-- =
`--.
=E2=95=9A=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=
=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=
=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=
=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=
=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=95=90=E2=
=95=90=E2=95=9D .---.....----.
Autoboot in 9 seconds, hit [Enter] to boot or any other key to stop
Loading kernel...
/boot/kernel/kernel text=3D0x95047c data=3D0x1919d0+0x84aa94
syms=3D[0x8+0x13aaa8+0x8+0x12610d]
Loading configured modules...
can't find '/boot/entropy'
Using DTB provided by EFI at 0x8000000.
---<<BOOT>>---
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2019 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 13.0-CURRENT 17a1fc80d57-c261519(upstream_master) GENERIC arm64
FreeBSD clang version 8.0.0 (tags/RELEASE_800/final 356365) (based on LLVM
8.0.0)
WARNING: WITNESS option enabled, expect reduced performance.
VT: init without driver.
Starting CPU 1 (1)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
[...]
Best regards,
Marcin
pon., 12 sie 2019 o 23:14 Mit Matelske <mit@pt.net> napisa=C5=82(a):
>
> Soren-
>
> Thanks for the quick response. I built this kernel with revision 350924.
> I'll dig into whats going on in the morning.
>
> Mind posting your diff for your loader.efi?
>
> Thanks again!
>
> Mit
>
>
> ----- Original Message -----
> From: "S=C3=B8ren Schmidt" <soren.schmidt@gmail.com>
> To: "Mit Matelske" <mit@pt.net>
> Cc: "tscho" <johannes@t-beutel.com>, "freebsd-arm" <
> freebsd-arm@freebsd.org>
> Sent: Monday, August 12, 2019 3:49:48 PM
> Subject: Re: Espressobin anyone ?
>
> Hi
>
> Looks like your sources may be too old, you need to be at least at r34888=
2
> to get the fix for the SD card VCC regulator.
>
> That change fixed it for me backported to 12-stable...
>
> The currdev problem still exists, I have it hardwired in my loader for
> aarch64 :)
>
> -S=C3=B8ren
>
>
> > On 12 Aug 2019, at 21.06, Mit Matelske <mit@pt.net> wrote:
> >
> > I'm having a couple little hiccups booting this board also. One has
> been commented on already, that I can't get the loader to automatically
> start loading the kernel on "disk0p2"...
> >
> > The second, is that the kernel can't find the SD card after booting so
> it can't mount the root filesystem. I'm using the dts/dtb and kernel fro=
m
> the 13-current branch.
> >
> > Thanks for any and all help. I haven't used u-boot in about decade.
> Spoiled by the x86 platform.
> >
> > Mit Matelske
> >
> >
> > ***U-boot environment:***
> >
> >
> > Marvell>> printenv
> > baudrate=3D115200
> > bootargs=3Dconsole=3DttyMV0,115200 earlycon=3Dar3700_uart,0xd0012000
> root=3D/dev/mmcblk0p1 rw rootwait net.ifnames=3D0 biosdevname=3D0
> > bootcmd=3Dmmc dev 0; fatload mmc 0:1 $kernel_addr $image_name;fatload m=
mc
> 0:1 $fdt_addr $fdt_name; bootefi $kernel_addr $fdt_addr
> > bootdelay=3D2
> > bootmmc=3Dmmc dev 0; fatload mmc 0:1 $kernel_addr $image_name;fatload m=
mc
> 0:1 $fdt_addr $fdt_name; bootefi $kernel_addr $fdt_addr
> > console=3Dconsole=3DttyMV0,115200 earlycon=3Dar3700_uart,0xd0012000
> > eth1addr=3D00:51:82:11:22:01
> > eth2addr=3D00:51:82:11:22:02
> > eth3addr=3D00:51:82:11:22:03
> > ethact=3Dneta@30000
> > ethaddr=3DF0:AD:4E:09:6B:8F
> > ethprime=3Deth0
> > fdt_addr=3D0x4f00000
> > fdt_high=3D0xffffffffffffffff
> > fdt_name=3Defi/boot/armada-3720-espressobin.dtb
> > fdtcontroladdr=3D3f7161b8
> > gatewayip=3D10.4.50.254
> > get_images=3Dtftpboot $kernel_addr $image_name; tftpboot $fdt_addr
> $fdt_name; run get_ramfs
> > get_ramfs=3Dif test "${ramfs_name}" !=3D "-"; then setenv ramfs_addr
> 0x8000000; tftpboot $ramfs_addr $ramfs_name; else setenv ramfs_addr -;fi
> > hostname=3Dmarvell
> > image_name=3Defi/freebsd/loader.efi
> > initrd_addr=3D0xa00000
> > initrd_size=3D0x2000000
> > ipaddr=3D0.0.0.0
> > kernel_addr=3D0x5000000
> > loadaddr=3D0x5000000
> > netdev=3Deth0
> > netmask=3D255.255.255.0
> > ramfs_addr=3D0x8000000
> > ramfs_name=3D-
> > root=3Droot=3D/dev/nfs rw
> > rootpath=3D/srv/nfs/
> > serverip=3D0.0.0.0
> > set_bootargs=3Dsetenv bootargs $console $root
> ip=3D$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:none
> nfsroot=3D$serverip:$rootpath $extra_params
> > stderr=3Dserial@12000
> > stdin=3Dserial@12000
> > stdout=3Dserial@12000
> >
> >
> > ***Full boot logs:***
> >
> >
> > U-Boot 2017.03-armada-17.10.2-g14aeedc (Jun 01 2018 - 15:39:10 +0800)
> >
> > Model: Marvell Armada 3720 Community Board ESPRESSOBin
> > CPU @ 1000 [MHz]
> > L2 @ 800 [MHz]
> > TClock @ 200 [MHz]
> > DDR @ 800 [MHz]
> > DRAM: 1 GiB
> > U-Boot DT blob at : 000000003f7161b8
> > Comphy-0: USB3 5 Gbps
> > Comphy-1: PEX0 2.5 Gbps
> > Comphy-2: SATA0 6 Gbps
> > SATA link 0 timeout.
> > AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
> > flags: ncq led only pmp fbss pio slum part sxs
> > PCIE-0: Link down
> > MMC: sdhci@d0000: 0, sdhci@d8000: 1
> > SF: Detected mx25u3235f with page size 256 Bytes, erase size 64 KiB,
> total 4 MiB
> > Net: eth0: neta@30000 [PRIME]
> > Hit any key to stop autoboot: 0
> > switch to partitions #0, OK
> > mmc0 is current device
> > reading efi/freebsd/loader.efi
> > 603872 bytes read in 49 ms (11.8 MiB/s)
> > reading efi/boot/armada-3720-espressobin.dtb
> > 15946 bytes read in 17 ms (916 KiB/s)
> > ## Starting EFI application at 05000000 ...
> > Scanning disk sdhci@d0000.blk...
> > Card did not respond to voltage select!
> > mmc_init: -95, time 50
> > Found 1 disks
> > Consoles: EFI console
> > FreeBSD/arm64 EFI loader, Revision 1.1
> >
> > Command line arguments: loader.efi
> > EFI version: 2.05
> > EFI Firmware: Das U-boot (rev 0.00)
> > Console: efi (0)
> > Failed to find bootable partition
> > Startup error in /boot/lua/loader.lua: seconds
> > LUA ERROR: cannot open /boot/lua/loader.lua: invalid argument.
> >
> > can't load 'kernel'
> >
> > Type '?' for a list of commands, 'help' for more detailed help.
> > OK
> > OK set currdev=3Ddisk0p2
> > OK boot
> >
> > /boot/kernel/kernel text=3D0x97d6a0 data=3D0x191b50+0x84ae94
> syms=3D[0x8+0x137dd8+0x8+0x126260]
> > Using DTB provided by EFI at 0x8000000.
> > ---<<BOOT>>---
> > KDB: debugger backends: ddb
> > KDB: current backend: ddb
> > Copyright (c) 1992-2019 The FreeBSD Project.
> > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 199=
4
> > The Regents of the University of California. All rights reserved=
.
> > FreeBSD is a registered trademark of The FreeBSD Foundation.
> > FreeBSD 13.0-CURRENT GENERIC arm64
> > FreeBSD clang version 6.0.1 (tags/RELEASE_601/final 335540) (based on
> LLVM 6.0.1)
> > WARNING: WITNESS option enabled, expect reduced performance.
> > VT: init without driver.
> > Starting CPU 1 (1)
> > FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
> > arc4random: WARNING: initial seeding bypassed the cryptographic random
> device because it was not yet seeded and the knob 'bypass_before_seeding'
> was enabled.
> > random: entropy device external interface
> > MAP 3e681000 mode 2 pages 1
> > MAP 3ffa6000 mode 2 pages 1
> > kbd0 at kbdmux0
> > ofwbus0: <Open Firmware Device Tree>
> > simplebus0: <Flattened device tree simple bus> on ofwbus0
> > simplebus1: <Flattened device tree simple bus> on simplebus0
> > simple_mfd0: <Simple MFD (Multi-Functions Device)> mem
> 0x13800-0x138ff,0x13c00-0x13c1f on simplebus1
> > simple_mfd1: <Simple MFD (Multi-Functions Device)> mem
> 0x18800-0x188ff,0x18c00-0x18c1f on simplebus1
> > psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
> > gic0: <ARM Generic Interrupt Controller v3.0> mem
> 0x1d00000-0x1d0ffff,0x1d40000-0x1d7ffff,0x1d80000-0x1d81fff,0x1d90000-0x1=
d91fff,0x1da0000-0x1dbffff
> irq 27 on simplebus1
> > gpio0: <Armada 37x0 North Bridge GPIO Controller> mem
> 0x13800-0x138ff,0x13c00-0x13c1f irq 28,29,30,31,32,33,34,35,36,37,38,39 o=
n
> simple_mfd0
> > gpio0: cannot allocate memory window
> > device_attach: gpio0 attach returned 6
> > gpio0: <Armada 37x0 South Bridge GPIO Controller> mem
> 0x18800-0x188ff,0x18c00-0x18c1f irq 40,41,42,43,44 on simple_mfd1
> > gpio0: cannot allocate memory window
> > device_attach: gpio0 attach returned 6
> > gpioregulator0: <GPIO controlled regulator> on ofwbus0
> > gpioregulator0: cannot get pin 0
> > gpioregulator0: cannot parse parameters
> > device_attach: gpioregulator0 attach returned 6
> > generic_timer0: <ARMv8 Generic Timer> irq 0,1,2,3 on ofwbus0
> > Timecounter "ARM MPCore Timecounter" frequency 12500000 Hz quality 1000
> > Event timer "ARM MPCore Eventtimer" frequency 12500000 Hz quality 1000
> > gpio0: <Armada 37x0 North Bridge GPIO Controller> mem
> 0x13800-0x138ff,0x13c00-0x13c1f irq 28,29,30,31,32,33,34,35,36,37,38,39 o=
n
> simple_mfd0
> > gpio0: cannot allocate memory window
> > device_attach: gpio0 attach returned 6
> > gpio0: <Armada 37x0 South Bridge GPIO Controller> mem
> 0x18800-0x188ff,0x18c00-0x18c1f irq 40,41,42,43,44 on simple_mfd1
> > gpio0: cannot allocate memory window
> > device_attach: gpio0 attach returned 6
> > gpioregulator0: <GPIO controlled regulator> on ofwbus0
> > gpioregulator0: cannot get pin 0
> > gpioregulator0: cannot parse parameters
> > device_attach: gpioregulator0 attach returned 6
> > gpio0: <Armada 37x0 North Bridge GPIO Controller> mem
> 0x13800-0x138ff,0x13c00-0x13c1f irq 28,29,30,31,32,33,34,35,36,37,38,39 o=
n
> simple_mfd0
> > gpio0: cannot allocate memory window
> > device_attach: gpio0 attach returned 6
> > gpio0: <Armada 37x0 South Bridge GPIO Controller> mem
> 0x18800-0x188ff,0x18c00-0x18c1f irq 40,41,42,43,44 on simple_mfd1
> > gpio0: cannot allocate memory window
> > device_attach: gpio0 attach returned 6
> > gpioregulator0: <GPIO controlled regulator> on ofwbus0
> > gpioregulator0: cannot get pin 0
> > gpioregulator0: cannot parse parameters
> > device_attach: gpioregulator0 attach returned 6
> > gpio0: <Armada 37x0 North Bridge GPIO Controller> mem
> 0x13800-0x138ff,0x13c00-0x13c1f irq 28,29,30,31,32,33,34,35,36,37,38,39 o=
n
> simple_mfd0
> > gpio0: cannot allocate memory window
> > device_attach: gpio0 attach returned 6
> > gpio0: <Armada 37x0 South Bridge GPIO Controller> mem
> 0x18800-0x188ff,0x18c00-0x18c1f irq 40,41,42,43,44 on simple_mfd1
> > gpio0: cannot allocate memory window
> > device_attach: gpio0 attach returned 6
> > gpioregulator0: <GPIO controlled regulator> on ofwbus0
> > gpioregulator0: cannot get pin 0
> > gpioregulator0: cannot parse parameters
> > device_attach: gpioregulator0 attach returned 6
> > gpio0: <Armada 37x0 North Bridge GPIO Controller> mem
> 0x13800-0x138ff,0x13c00-0x13c1f irq 28,29,30,31,32,33,34,35,36,37,38,39 o=
n
> simple_mfd0
> > gpio0: cannot allocate memory window
> > device_attach: gpio0 attach returned 6
> > gpio0: <Armada 37x0 South Bridge GPIO Controller> mem
> 0x18800-0x188ff,0x18c00-0x18c1f irq 40,41,42,43,44 on simple_mfd1
> > gpio0: cannot allocate memory window
> > device_attach: gpio0 attach returned 6
> > gpioregulator0: <GPIO controlled regulator> on ofwbus0
> > gpioregulator0: cannot get pin 0
> > gpioregulator0: cannot parse parameters
> > device_attach: gpioregulator0 attach returned 6
> > cpulist0: <Open Firmware CPU Group> on ofwbus0
> > cpu0: <Open Firmware CPU> on cpulist0
> > cpu1: <Open Firmware CPU> on cpulist0
> > pmu0: <Performance Monitoring Unit> irq 4 on ofwbus0
> > syscon_generic0: <syscon> mem 0xd000-0xdfff on simplebus1
> > syscon_generic1: <syscon> mem 0x11500-0x1153f on simplebus1
> > uart0: <Marvell Armada 3700 UART> mem 0x12000-0x121ff irq 9,10,11 on
> simplebus1
> > uart0: console (115200,n,8,1)
> > gpio0: <Armada 37x0 North Bridge GPIO Controller> mem
> 0x13800-0x138ff,0x13c00-0x13c1f irq 28,29,30,31,32,33,34,35,36,37,38,39 o=
n
> simple_mfd0
> > gpio0: cannot allocate memory window
> > device_attach: gpio0 attach returned 6
> > syscon_generic2: <syscon> mem 0x14000-0x1405f on simplebus1
> > gpio0: <Armada 37x0 South Bridge GPIO Controller> mem
> 0x18800-0x188ff,0x18c00-0x18c1f irq 40,41,42,43,44 on simple_mfd1
> > gpio0: cannot allocate memory window
> > device_attach: gpio0 attach returned 6
> > mvneta0: <NETA controller> mem 0x30000-0x33fff irq 14 on simplebus1
> > mvneta0: version is 10
> > mvneta0: Ethernet address: 00:a6:39:ca:e8:00
> > mdio0: <MDIO> on mvneta0
> > mdioproxy0: <MII/MDIO proxy, MDIO side> on mdio0
> > e6000sw0: <Marvell 88E6341> on mdio0
> > e6000sw0: multi-chip addressing mode (0x1)
> > e6000sw0: CPU port at 0
> > e6000sw0: fixed port at 0
> > e6000sw0: PHY at port 1
> > miibus0: <MII bus> on e6000sw0
> > e1000phy0: <Marvell 88E1000 Gigabit PHY> PHY 17 on miibus0
> > e1000phy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
> 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
> > e6000sw0: PHY at port 2
> > miibus1: <MII bus> on e6000sw0
> > e1000phy1: <Marvell 88E1000 Gigabit PHY> PHY 18 on miibus1
> > e1000phy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
> 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
> > e6000sw0: PHY at port 3
> > miibus2: <MII bus> on e6000sw0
> > e1000phy2: <Marvell 88E1000 Gigabit PHY> PHY 19 on miibus2
> > e1000phy2: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
> 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
> > e6000sw0: switch is ready.
> > etherswitch0: <Switch controller> on e6000sw0
> > xhci0: <Generic USB 3.0 controller> mem 0x58000-0x5bfff irq 16 on
> simplebus1
> > xhci0: 32 bytes context size, 32-bit DMA
> > usbus0 on xhci0
> > syscon_generic3: <syscon> mem 0x5d800-0x5dfff on simplebus1
> > ehci0: <Marvell Integrated USB 2.0 controller> mem 0x5e000-0x5efff irq
> 17 on simplebus1
> > usbus1: EHCI version 1.0
> > usbus1 on ehci0
> > syscon_generic4: <syscon> mem 0x5f800-0x5ffff on simplebus1
> > sdhci_xenon0: <Armada Xenon SDHCI controller> mem
> 0xd0000-0xd02ff,0x1e808-0x1e80b irq 24 on simplebus1
> > ahci0: <AHCI SATA controller> mem 0xe0000-0xe0177 irq 26 on simplebus1
> > ahci0: AHCI v1.30 with 1 6Gbps ports, Port Multiplier supported with FB=
S
> > ahcich0: <AHCI channel> at channel 0 on ahci0
> > device_attach: ahcich0 attach returned 6
> > gpioregulator0: <GPIO controlled regulator> on ofwbus0
> > gpioregulator0: cannot get pin 0
> > gpioregulator0: cannot parse parameters
> > device_attach: gpioregulator0 attach returned 6
> > cryptosoft0: <software crypto>
> > Timecounters tick every 1.000 msec
> > mvneta0: link state changed to UP
> > e6000sw0port1: link state changed to DOWN
> > e6000sw0port2: link state changed to DOWN
> > e6000sw0port3: link state changed to DOWN
> > usbus0: 5.0Gbps Super Speed USB v3.0
> > usbus1: 480Mbps High Speed USB v2.0
> > Release APs...done
> > CPU 0: ARM Cortex-A53 r0p4 affinity: 0
> > Instruction Set Attributes 0 =3D <CRC32,SHA2,SHA1,AES+PMULL>
> > Trying to mount root from ufs:/dev/ufs/FreeBSD_Install [ro,noatime]...
> > Instruction Set Attributes 1 =3D <>
> > Root mount waiting for: Processor Features 0 =3D
> <GIC,AdvSIMD,Float,EL3 32,EL2 32,EL1 32,EL0 32>
> > usbus1 Processor Features 1 =3D <0>
> > usbus0 Memory Model Features 0 =3D <4k Granule,64k Granule,S/NS
> Mem,MixedEndian,16bit ASID,1TB PA>
> >
> > Memory Model Features 1 =3D <>
> > Memory Model Features 2 =3D <32b CCIDX,48b VA>
> > Debug Features 0 =3D <2 CTX Breakpoints,4 Watchpoints,6
> Breakpoints,PMUv3,Debug v8>
> > Debug Features 1 =3D <0>
> > Auxiliary Features 0 =3D <0>
> > Auxiliary Features 1 =3D <0>
> > CPU 1: ARM Cortex-A53 r0p4 affinity: 1
> > WARNING: WITNESS option enabled, expect reduced performance.
> > ugen0.1: <Generic XHCI root HUB> at usbus0
> > ugen1.1: <Marvell EHCI root HUB> at usbus1
> > uhub0 on usbus0
> > uhub1 on usbus1
> > uhub0: <Generic XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on
> usbus0
> > uhub1: <Marvell EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on
> usbus1
> > uhub0: 2 ports with 2 removable, self powered
> > uhub1: 1 port with 1 removable, self powered
> > mountroot: waiting for device /dev/ufs/FreeBSD_Install...
> > Mounting from ufs:/dev/ufs/FreeBSD_Install failed with error 19.
> >
> > Loader variables:
> > vfs.root.mountfrom=3Dufs:/dev/ufs/FreeBSD_Install
> > vfs.root.mountfrom.options=3Dro,noatime
> >
> > Manual root filesystem specification:
> > <fstype>:<device> [options]
> > Mount <device> using filesystem <fstype>
> > and with the specified (optional) option list.
> >
> > eg. ufs:/dev/da0s1a
> > zfs:zroot/ROOT/default
> > cd9660:/dev/cd0 ro
> > (which is equivalent to: mount -t cd9660 -o ro /dev/cd0 /)
> >
> > ? List valid disk boot devices
> > . Yield 1 second (for background tasks)
> > <empty line> Abort manual input
> >
> > mountroot> ?
> >
> > List of GEOM managed disk devices:
> >
> >
> > mountroot>
> _______________________________________________
> freebsd-arm@freebsd.org mailing list
> https://lists.freebsd.org/mailman/listinfo/freebsd-arm
> To unsubscribe, send any mail to "freebsd-arm-unsubscribe@freebsd.org"
>
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?CAPv3WKeMEe9mW8YYS8k=J9obwde9KEidMHHQpPJ0idrhcyx=RQ>