Date: Fri, 01 Aug 2003 22:25:19 -0400 From: Bill Moran <wmoran@potentialtech.com> To: current@freebsd.org Subject: Re: Problem making a gateway from 5.1-RELEASE Message-ID: <3F2B210F.1040001@potentialtech.com> In-Reply-To: <3F2B1E08.9020304@potentialtech.com> References: <3F2B1E08.9020304@potentialtech.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Nevermind. I think I've been working too many hours. The problem was a stupid nat misconfiguration that I have now fixed. The strange behaviour this was causing misled me to believe one of the NICs wasn't working correctly. Bill Moran wrote: > Hey, > > This isn't quite -CURRENT, but it's 5.1-RELEASE. > > I'm trying to put together a typical nat/gateway box. But I can't > seem to get both network cards to work at the same time. I've tried > a 3com card, a realtek card, as well as the onboard sis chipset card. > One card always works, the other seems to work (it gets a DHCP addy) > but I can't ping or otherwise communicate via it. Although it seems > to be communicating somehow, as the output of netstat show that it > sees the other machines chattering on its subnet. Sometimes it's the > 3com that works, other times it's the realtek, depending on which > devices are installed/enabled. I don't see any interrupt conflicts. > > Below is the dmesg from when the 3com and realtek were installed with > the onboard sis disabled. Does anyone have any ideas as to what's > going on? Is this a case of the hardware just being too cheap? > > Copyright (c) 1992-2003 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 5.1-RELEASE #2: Sat Aug 2 07:46:12 GMT 2003 > root@proxy.novadental.com:/usr/obj/usr/src/sys/PROXY > Preloaded elf kernel "/boot/kernel/kernel" at 0xc03f9000. > Preloaded elf module "/boot/kernel/acpi.ko" at 0xc03f9244. > Timecounter "i8254" frequency 1193182 Hz > Timecounter "TSC" frequency 1693130944 Hz > CPU: Intel(R) Celeron(R) CPU 1.70GHz (1693.13-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0xf13 Stepping = 3 > > Features=0x3febfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM> > > real memory = 100597760 (95 MB) > avail memory = 93331456 (89 MB) > Pentium Pro MTRR support enabled > npx0: <math processor> on motherboard > npx0: INT 16 interface > acpi0: <AWARD AWRDACPI> on motherboard > pcibios: BIOS version 2.10 > Using $PIR table, 6 entries at 0xc00fdc90 > acpi0: power button is handled as a fixed feature programming model. > Timecounter "ACPI-fast" frequency 3579545 Hz > acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 > acpi_cpu0: <CPU> on acpi0 > acpi_tz0: <thermal zone> on acpi0 > acpi_button0: <Power Button> on acpi0 > pcib0: <ACPI Host-PCI bridge> port > 0x10c0-0x10ff,0x1000-0x10bf,0x480-0x48f,0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > agp0: <SIS Generic host to PCI bridge> mem 0xe8000000-0xebffffff at > device 0.0 on pci0 > pcib1: <PCIBIOS PCI-PCI bridge> at device 1.0 on pci0 > pci1: <PCI bus> on pcib1 > pci1: <display, VGA> at device 0.0 (no driver attached) > isab0: <PCI-ISA bridge> at device 2.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <SiS 96X UDMA133 controller> port > 0x4000-0x400f,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 at device > 2.5 on pci0 > ata0: at 0x1f0 irq 14 on atapci0 > ata1: at 0x170 irq 15 on atapci0 > pci0: <multimedia, audio> at device 2.7 (no driver attached) > pci0: <serial bus, USB> at device 3.0 (no driver attached) > pci0: <serial bus, USB> at device 3.1 (no driver attached) > pci0: <serial bus, USB> at device 3.3 (no driver attached) > dc0: <3Com OfficeConnect 10/100B> port 0xe000-0xe0ff mem > 0xed102000-0xed1023ff irq 5 at device 6.0 on pci0 > dc0: Ethernet address: 00:04:75:b5:27:2c > miibus0: <MII bus> on dc0 > ukphy0: <Generic IEEE 802.3u media interface> on miibus0 > ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > rl0: <RealTek 8139 10/100BaseTX> port 0xe400-0xe4ff mem > 0xed104000-0xed1040ff irq 11 at device 8.0 on pci0 > rl0: Realtek 8139B detected. Warning, this may be unstable in autoselect > mode > rl0: Ethernet address: 00:c0:ca:14:03:eb > miibus1: <MII bus> on rl0 > rlphy0: <RealTek internal media interface> on miibus1 > rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port > 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0 > fdc0: FIFO enabled, 8 bytes threshold > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > sio0 port 0x3f8-0x3ff irq 4 on acpi0 > sio0: type 16550A > ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0 > ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode > ppc0: FIFO with 16/16/9 bytes threshold > ppbus0: <Parallel port bus> on ppc0 > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 > atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 > kbd0 at atkbd0 > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > psm0: model IntelliMouse, device ID 3 > orm0: <Option ROM> at iomem 0xc0000-0xc7fff on isa0 > pmtimer0 on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio1: configured irq 3 not in bitmap of probed irqs 0 > sio1: port may not be enabled > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > Timecounters tick every 10.000 msec > ipfw2 initialized, divert disabled, rule-based forwarding enabled, > default to deny, logging unlimited > ad0: 38166MB <WDC WD400BB-00DEA0> [77545/16/63] at ata0-master UDMA100 > acd0: CDROM <ATAPI CD-ROM 52XMax> at ata1-slave PIO4 > Mounting root from ufs:/dev/ad0s1a > > _______________________________________________ > freebsd-current@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-current > To unsubscribe, send any mail to "freebsd-current-unsubscribe@freebsd.org" > > -- Bill Moran Potential Technologies http://www.potentialtech.com
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3F2B210F.1040001>