Date: Fri, 11 Dec 2015 21:44:13 -0500 From: "Michael B. Eichorn" <ike@michaeleichorn.com> To: marcel <marcel.plouf@gmail.com>, Dirk Engling <erdgeist@erdgeist.org>, freebsd-jail@freebsd.org Subject: Re: Configuring network without ezjail Message-ID: <1449888253.23602.14.camel@michaeleichorn.com> In-Reply-To: <566B8183.3080306@gmail.com> References: <566B67F7.1090404@gmail.com> <566B5CB6.8050009@erdgeist.org> <566B7D7E.2070507@gmail.com> <566B8183.3080306@gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Sat, 2015-12-12 at 02:08 +0000, marcel wrote:
> ... and I think I have enabling gateway, I wrote thins in both of my
> rc.conf (jail and host):
>
> gateway_enable="YES"
>
> Is it correct ?
You only need gateway_enable if you are doing routing, it is not
necessary for a typical jail setup. Most of the time you are just
adding an alias to the host's nic.
>
> But I don't think I have DNS problems, my host correctly access to
> the
> internet and the resolv.conf of my jail and my host are same...
>
> On 12/12/2015 01:50, marcel wrote:
> > No I don't get to have an IP address... Yet I have writed this in
> > my
> > host's rc.conf:
> >
> > jail_enable="YES"
> > jail_list="thename"
> > jail_guantanamo_rootdir="thepath"
> > jail_guantanamo_hostname="thename"
> > jail_guantanamo_ip="192.168.0.12"
> >
> > and I use the command:
> >
> > jail thepath thename 192.168.0.12 /bin/csh
> >
> > to connect to my jail...
> >
> > On 11/12/2015 23:31, Dirk Engling wrote:
> > > On 12.12.15 01:19, marcel wrote:
> > >
> > > > I would like to know if it is possible to configure a jail's
> > > > network for
> > > > accessing to the World Wide Web but without ezjail ?
> > > > I have created my jail without ezjail (mkdir jail, make
> > > > installworld,
> > > > etc...) and I would like to continue without it if it's
> > > > possible...
> > > Sure, why doesn't it connect to the net? Does it have a RFC1918
> > > IP? If
> > > so, you need to enable NAT. If not, did you enable gatewaying?
> > > Maybe you
> > > just have DNS problems, so is your resolv.conf set up properly?
> > >
> > > Without knowing what exactly is not working, I can not help you.
> > >
> > > erdgeist
I think you found some old instructions, assuming a 10.x system here is
the boilerplate for a typical jail:
rc.conf:
jail_enable="YES"
jail.conf:
interface = re0;
mount.devfs;
exec.start = "/bin/sh /etc/rc";
exec.stop = "/bin/sh /etc/rc.shutdown";
thenameofthejail {
host.hostname = host.domain.tld;
path = /the/path/to/the/jail
ip4.addr = 192.168.0.12;
}
and start it up with
# jail -c thenameofthejail
And another handy tip you can avoid building a jail with make by
extacting the base.txz file found in places like the install media into
the jail directory.
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1449888253.23602.14.camel>