Date: Thu, 31 Aug 2000 23:52:33 -0500 From: Dave Uhring <duhring@charter.net> To: Roger Merritt <mcrogerm@stjohn.ac.th>, freebsd-stable@FreeBSD.ORG Subject: Re: ata0-slave doesn't show up! Message-ID: <00083123523300.00265@dave.uhring.com> In-Reply-To: <3.0.6.32.20000901105303.008c39d0@stjohn.stjohn.ac.th> References: <3.0.6.32.20000901105303.008c39d0@stjohn.stjohn.ac.th>
next in thread | previous in thread | raw e-mail | index | archive | help
--------------Boundary-00=_LVY67JRPWDJ9LT8AESK2
Content-Type: text/plain
Content-Transfer-Encoding: 8bit
On Thu, 31 Aug 2000, Roger Merritt wrote:
> Has anybody found a solution to this yet? My workaround was to go back
> to the wdc device rather than the ata device, but it might be better
> for me to back down from 4.1-STABLE to 4.1-RELEASE and use the newer
> device. My CD-ROM is at ata0-slave and also wasn't being detected at
> bootup. Exactly the same symptoms as below.
>
-----------snip of dmesg and conf file ------------------
See dmesg from my system:
Dave
--------------Boundary-00=_LVY67JRPWDJ9LT8AESK2
Content-Type: text/english;
name="dmesg"
Content-Transfer-Encoding: 8bit
Content-Disposition: attachment; filename="dmesg"
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.1-STABLE #0: Wed Aug 30 15:55:22 CDT 2000
duhring@dave.uhring.com:/usr/obj/usr/src/sys/dave
Timecounter "i8254" frequency 1193182 Hz
CPU: AMD-K6(tm) 3D processor (451.03-MHz 586-class CPU)
Origin = "AuthenticAMD" Id = 0x58c Stepping = 12
Features=0x8021bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,PGE,MMX>
AMD Features=0x80000800<SYSCALL,3DNow!>
real memory = 134152192 (131008K bytes)
config> di pcic0
No such device: pcic0
Invalid command or syntax. Type `?' for help.
config> di sn0
No such device: sn0
Invalid command or syntax. Type `?' for help.
config> di lnc0
No such device: lnc0
Invalid command or syntax. Type `?' for help.
config> di le0
No such device: le0
Invalid command or syntax. Type `?' for help.
config> di ie0
No such device: ie0
Invalid command or syntax. Type `?' for help.
config> di fe0
No such device: fe0
Invalid command or syntax. Type `?' for help.
config> di ed0
No such device: ed0
Invalid command or syntax. Type `?' for help.
config> di cs0
No such device: cs0
Invalid command or syntax. Type `?' for help.
config> di bt0
No such device: bt0
Invalid command or syntax. Type `?' for help.
config> di aic0
No such device: aic0
Invalid command or syntax. Type `?' for help.
config> di aha0
No such device: aha0
Invalid command or syntax. Type `?' for help.
config> di adv0
No such device: adv0
Invalid command or syntax. Type `?' for help.
config> q
avail memory = 127315968 (124332K bytes)
Preloaded elf kernel "kernel" at 0xc0346000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc034609c.
K6-family MTRR support enabled (2 registers)
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
agp0: <VIA 82C597 (Apollo VP3) host to PCI bridge> mem 0xe5000000-0xe53fffff at device 0.0 on pci0
pcib1: <VIA 82C598MVP (Apollo MVP3) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <ATI Mach64-GB graphics accelerator> at 0.0
isab0: <VIA 82C586 PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C586 ATA33 controller> port 0xe400-0xe40f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pcib2: <PCI to PCI bridge (vendor=1106 device=3040)> at device 7.3 on pci0
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xe800-0xe81f mem 0xe5400000-0xe54fffff,0xe5500000-0xe5500fff irq 10 at device 9.0 on pci0
fxp0: Ethernet address 00:a0:c9:39:62:0f
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
fd1: <1200-KB 5.25" drive> on fdc0 drive 1
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: IEEE1284 device found /NIBBLE/ECP
Probing for PnP devices on ppbus0:
ppbus0: <HEWLETT-PACKARD DESKJET 810C> MLC,PCL,PML
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sbc0: <Creative SB16/SB32> at port 0x220-0x22f,0x330-0x331,0x388-0x38b irq 5 drq 1,5 on isa0
sbc0: setting card to irq 5, drq 1, 5
pcm0: <SB DSP 4.13> on sbc0
unknown0: <Reserved> at port 0x100 on isa0
unknown1: <Reserved> at port 0x108 on isa0
unknown2: <Game> at port 0x200-0x207 on isa0
ata1-slave: ata_command: timeout waiting for intr
ata1-slave: identify failed
ad0: 12427MB <Maxtor 91303D6> [25249/16/63] at ata0-master using UDMA33
ad1: 1220MB <Maxtor 81275 A3> [2480/16/63] at ata0-slave using WDMA2
acd0: CDROM <IDE/ATAPI CD-ROM 44XS> at ata1-master using UDMA33
Mounting root from ufs:/dev/ad0s2a
pid 273 (kcmdisplay), uid 1001: exited on signal 11 (core dumped)
pid 275 (kcmdisplay), uid 1001: exited on signal 11 (core dumped)
pid 716 (kcmdisplay), uid 1001: exited on signal 11 (core dumped)
pid 717 (kcmdisplay), uid 1001: exited on signal 11 (core dumped)
pid 718 (kcmdisplay), uid 1001: exited on signal 11 (core dumped)
pid 721 (kcmkwm), uid 1001: exited on signal 11 (core dumped)
pid 722 (kcmkwm), uid 1001: exited on signal 6 (core dumped)
pid 726 (kcmkwm), uid 1001: exited on signal 11 (core dumped)
--------------Boundary-00=_LVY67JRPWDJ9LT8AESK2--
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?00083123523300.00265>