Date: Sun, 1 Mar 1998 12:09:48 -0800 (PST) From: Ulf Zimmermann <ulf@Alameda.net> To: abial@nask.pl (Andrzej Bialecki) Cc: ulf@Alameda.net, hackers@FreeBSD.ORG Subject: Re: Intel DK440LX motherboard with EtherExpress Pro/100B on board Message-ID: <199803012009.MAA23799@Gatekeeper.Alameda.net> In-Reply-To: <Pine.NEB.3.95.980301204159.20158A-100000@korin.warman.org.pl> from Andrzej Bialecki at "Mar 1, 98 08:46:37 pm"
next in thread | previous in thread | raw e-mail | index | archive | help
> On Sun, 1 Mar 1998, Ulf Zimmermann wrote: > > > > On Sun, 1 Mar 1998, Ulf Zimmermann wrote: > > > > > > > Hi. > > > > > > > > I bought an Intel DK440LX motherboard (Dual PII, Adaptec AIC-7895, Crystal > > > > sound card and EtherExpress Pro/100B onboard). The fxp driver seems to > > > > have a little problem: > > > > > > > > fxp0: <Intel EtherExpress Pro 10/100B Ethernet> rev 0x02 int a irq 11 on pci0.3.0 > > > > fxp0: Ethernet address 00:a0:c9:61:68:05 > > > > fxp0: warning: unsupported PHY, type = 11, addr = 1 > > > > > > The same warning in my case. But see below. > > > > > > > > > > > Ifconfig shows: > > > > > > > > fxp0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 > > > > inet 207.90.181.122 netmask 0xffffff80 broadcast 207.90.181.127 > > > > ether 00:a0:c9:61:68:05 > > > > media: manual > > > > supported media: manual > > > > > > > > And you can't set anything via "ifconfig media ... mediaopt" > > > > > > Hmmm. Not in my case - it works perfectly. But I run -current on it, and > > > you forgot to tell us your version... ;-) > > > > 2.2.5 RELEASE and 3.0-current SNAP 980228 > > Ok. You'll have to wait till tomorrow, when I'm at work and can check the > exact revision of the chip and so on... Do you use it in 10Mbps or > 100Mbps? I use it only in 10Mbps mode... > > Andrzej Bialecki Hub says: Port Name Status Vlan Level Duplex Speed Type ----- ------------------ ---------- ---------- ------ ------ ----- ------------ 5/11 connected 1 normal full 100 10/100BaseTX And I just checked transfer rates, very bad. many runts. Switched hub from Full Duplex 100 to Auto and it still shows Full Duplex and 100, but much better transfer rate. Ulf. --------------------------------------------------------------------- Ulf Zimmermann, 1525 Pacific Ave., Alameda, CA-94501, #: 510-769-2936 Alameda Networks, Inc. | http://www.Alameda.net | Fax#: 510-521-5073 To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-hackers" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199803012009.MAA23799>