Date: Sat, 20 Jan 2001 10:54:39 +0100 From: Jan Chrillesen <jan@chrillesen.dk> To: Charlie Rewt <invalid-address@free-pr0n.netscum.dk> Cc: mjacob@feral.com, freebsd-hardware@FreeBSD.ORG, usenet@tdk.net Subject: Re: Intel wiseman and livengood gigabit ethernet support Message-ID: <20010120105439.G10685@vax.chrillesen.dk> In-Reply-To: <200101192209.f0JM9pD93464@crotchety.newsbastards.org>; from invalid-address@free-pr0n.netscum.dk on Fri, Jan 19, 2001 at 11:09:51PM %2B0100 References: <Pine.LNX.4.21.0012050908050.14082-100000@zeppo.feral.com> <200101192209.f0JM9pD93464@crotchety.newsbastards.org>
next in thread | previous in thread | raw e-mail | index | archive | help
On Fri, 19 Jan 2001, Charlie Rewt <invalid-address@free-pr0n.netscum.dk> wrote: > We did add one of these cards to a FreeBSD 4-STABLE machine and it > is detected by the wx driver as follows, but we can't see any packets > going into it. I was not around for the networking that resulted in > the following kernel messages, so I don't know what all was done. I was the one who added the card to the box so I should probably follow up on Barrys posting. The card is detected by FreeBSD and both ends of the fibre gets link. (The other end is a Cisco Catalyst 6509). It seems that the card receives data but don't transmit anything. The RX led on the NIC lights up and this is the output from "show interface" on the switch: GigabitEthernet2/4 is up, line protocol is up Hardware is C6k 1000Mb 802.3, address is 0030.8035.1673 (bia 0030.8035.1673) Description: binary peering MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Full-duplex, 1000Mb/s ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output never, output hang never Last clearing of "show interface" counters 1d12h Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/2000, 0 drops 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1158000 bits/sec, 1650 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 input packets with dribble condition detected 286169898 packets output, 1023841019 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out This *could* be a bad fiber but since the link led lights up in both ends I don't think the fibre is the issue. I tried changing the GBIC in the switch since we've seen a bad GBIC before. > Jan 18 10:19:43 news-feed69 /kernel: wx0: receive sequence error This happened when I pulled the fibre to change the GBIC. Again this indicates that the NIC receives data. > Jan 18 10:21:21 news-feed69 /kernel: wx0: promiscuous mode enabled > [...] > Jan 18 10:22:19 news-feed69 /kernel: wx0: promiscuous mode disabled I fired up tcpdump to see if the kernel got any data from the NIC. tcpdump didn't show any packets :( > Just what would be the difference between LIVENGOOD and LIVENGOOD_SC > anyway? Is the _SC the copper rather than fiber? I'm trying to wrap > my brane around the differences between the FreeBSD and Linux vendor/ > device IDs... SC is the fiber connector. /jan To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-hardware" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20010120105439.G10685>