Date: Tue, 11 Feb 2003 00:26:35 +0530 From: Shantanu Mahajan <shantanoo+fbsd@ieee.org> To: Darren Spruell <darren_spruell@sento.com> Cc: freebsd-questions@freebsd.org Subject: Re: X problems on i810 | AddScreen/ScreenInit failed Message-ID: <20030210185635.GA694@dhumketu.homeunix.net>
next in thread | raw e-mail | index | archive | help
try adding following lines in Device section Option "NoDDC" in Monitor section Option "DPMS" Regards, Shantanu +++ Darren Spruell [freebsd] [10-02-03 11:07 -0700]: | Date: Mon, 10 Feb 2003 11:07:22 -0700 | From: Darren Spruell <darren_spruell@sento.com> | Subject: X problems on i810 | AddScreen/ScreenInit failed | | Greetz, | | I'm trying to configure v4.7 to run X but am having a hard time getting | the server to start. | | I've followed the config instructions at | http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/x-config.html | by doing the following steps: | | Run XFree86 -configure | to create the default XF86Config.new | Run XFree86 -xf86config ./XF86Config.new | to ensure that it works w/my hardware | Edit it to taste, to change specifics for HorizSync, VertRefresh, and | the Display subsection under "Screen". | | However, running 'XFree86 -xf86config ./XF86Config.new' after changing | my config does not work. The output error is: | | ====================================================================== | (==) VGA(0): Write-combining range (0xa0000,0x10000) was already clear | | Fatal server error: | AddScreen/ScreenInit failed for driver 0 | ====================================================================== | | I followed through the part in the Advanced Configuration section about | adding in support for agpgart and created the device node and added the | following to /boot/loader.conf: | agp_load="YES" | | dmesg now shows: | Preloaded elf module "agp.ko" at 0xc051a09c. | agp0: <Intel 82810-DC100 (i810-DC100 GMCH) SVGA controller> mem | 0xffa80000-0xffafffff,0xf8000000-0xfbffffff irq 11 at device 1.0 on pci0 | | Here is the current XF86Config.new (non-working). The Monitor section | was taken from a specs page on the Monitor (Gateway EV700). Full dmesg | included below this: | | Section "ServerLayout" | Identifier "XFree86 Configured" | Screen 0 "Screen0" 0 0 | InputDevice "Mouse0" "CorePointer" | InputDevice "Keyboard0" "CoreKeyboard" | EndSection | | Section "Files" | RgbPath "/usr/X11R6/lib/X11/rgb" | ModulePath "/usr/X11R6/lib/modules" | FontPath "/usr/X11R6/lib/X11/fonts/misc/" | FontPath "/usr/X11R6/lib/X11/fonts/Speedo/" | FontPath "/usr/X11R6/lib/X11/fonts/Type1/" | FontPath "/usr/X11R6/lib/X11/fonts/75dpi/" | FontPath "/usr/X11R6/lib/X11/fonts/100dpi/" | EndSection | | Section "Module" | Load "dbe" | Load "dri" | Load "extmod" | Load "glx" | Load "pex5" | Load "record" | Load "xie" | Load "xtrap" | Load "speedo" | Load "type1" | EndSection | | Section "InputDevice" | Identifier "Keyboard0" | Driver "keyboard" | EndSection | | Section "InputDevice" | Identifier "Mouse0" | Driver "mouse" | Option "Protocol" "MouseSystems" | Option "Device" "/dev/sysmouse" | EndSection | | Section "Monitor" | Identifier "Monitor0" | VendorName "Gateway" | ModelName "EV700" | HorizSync 30 - 69 | VertRefresh 50 - 110 | EndSection | | Section "Device" | ### Available Driver options are:- | ### Values: <i>: integer, <f>: float, <bool>: "True"/"False", | ### <string>: "String", <freq>: "<f> Hz/kHz/MHz" | ### [arg]: arg optional | #Option "ShadowFB" # [<bool>] | #Option "VGAClocks" # [<bool>] | Identifier "Card0" | Driver "vga" | VendorName "Intel" | BoardName "i810-dc100" | BusID "PCI:0:1:0" | EndSection | | Section "Screen" | Identifier "Screen0" | Device "Card0" | Monitor "Monitor0" | DefaultDepth 16 | SubSection "Display" | Depth 16 | Modes "1024x768" | EndSubSection | EndSection | | Copyright (c) 1992-2002 The FreeBSD Project. | Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 | The Regents of the University of California. All rights reserved. | FreeBSD 4.7-RELEASE #0: Wed Oct 9 15:08:34 GMT 2002 | root@builder.freebsdmall.com:/usr/obj/usr/src/sys/GENERIC | Timecounter "i8254" frequency 1193182 Hz | CPU: Pentium III/Pentium III Xeon/Celeron (697.88-MHz 686-class CPU) | Origin = "GenuineIntel" Id = 0x686 Stepping = 6 | | Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> | real memory = 267124736 (260864K bytes) | avail memory = 254693376 (248724K bytes) | Preloaded elf kernel "kernel" at 0xc051a000. | Preloaded elf module "agp.ko" at 0xc051a09c. | Pentium Pro MTRR support enabled | md0: Malloc disk | Using $PIR table, 11 entries at 0xc00f35a0 | npx0: <math processor> on motherboard | npx0: INT 16 interface | pcib0: <Intel 82810-DC100 (i810-DC100 GMCH) Host To Hub bridge> on | motherboard | pci0: <PCI bus> on pcib0 | agp0: <Intel 82810-DC100 (i810-DC100 GMCH) SVGA controller> mem | 0xffa80000-0xffafffff,0xf8000000-0xfbffffff irq 11 at device 1.0 on pci0 | pcib1: <Intel 82801AA (ICH) Hub to PCI bridge> at device 30.0 on pci0 | pci1: <PCI bus> on pcib1 | fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xdf00-0xdf3f mem | 0xff700000-0xff7fffff,0xff8ff000-0xff8fffff irq 3 at device 1.0 on pci1 | fxp0: Ethernet address 00:03:47:0b:0e:20 | inphy0: <i82555 10/100 media interface> on miibus0 | inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto | isab0: <Intel 82801AA (ICH) PCI to LPC bridge> at device 31.0 on pci0 | isa0: <ISA bus> on isab0 | atapci0: <Intel ICH ATA66 controller> port 0xffa0-0xffaf at device 31.1 | on pci0 | ata0: at 0x1f0 irq 14 on atapci0 | ata1: at 0x170 irq 15 on atapci0 | uhci0: <Intel 82801AA (ICH) USB controller> port 0xef80-0xef9f irq 10 at | device 31.2 on pci0 | usb0: <Intel 82801AA (ICH) USB controller> on uhci0 | usb0: USB revision 1.0 | uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 | uhub0: 2 ports with 2 removable, self powered | pci0: <unknown card> (vendor=0x8086, dev=0x2413) at 31.3 irq 9 | chip1: <Intel 82801AA (ICH) AC'97 Audio Controller> port | 0xef00-0xef3f,0xe800-0xe8ff irq 9 at device 31.5 on pci0 | orm0: <Option ROMs> at iomem 0xc0000-0xc9fff,0xcc000-0xccfff on isa0 | fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 | fdc0: FIFO enabled, 8 bytes threshold | fd0: <1440-KB 3.5" drive> on fdc0 drive 0 | atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 | atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 | kbd0 at atkbd0 | psm0: failed to get data. | psm0: <PS/2 Mouse> irq 12 on atkbdc0 | psm0: model IntelliMouse, device ID 3 | vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 | sc0: <System console> at flags 0x100 on isa0 | sc0: VGA <16 virtual consoles, flags=0x300> | sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 | sio0: type 16550A | sio1: configured irq 3 not in bitmap of probed irqs 0 | ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 | ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode | ppc0: FIFO with 16/16/8 bytes threshold | plip0: <PLIP network interface> on ppbus0 | lpt0: <Printer> on ppbus0 | lpt0: Interrupt-driven port | ppi0: <Parallel I/O> on ppbus0 | ad0: 14324MB <QUANTUM FIREBALLlct15 15> [29104/16/63] at ata0-master UDMA66 | acd0: MODE_SENSE_BIG trying to write on read buffer | acd0: MODE_SENSE_BIG - NO SENSE asc=0x00 ascq=0x00 error=0x04 | acd0: CDROM <CD-224E> at ata1-slave PIO4 | Mounting root from ufs:/dev/ad0s1a | WARNING: / was not properly dismounted | | | THANKS IN ADVANCE!!! | | - -- | Darren Spruell | Sento IS Department | darren_spruell@sento.com | | ------------------------------ | | End of questions-digest V5 #1894 | ******************************** | | To Unsubscribe: send mail to majordomo@FreeBSD.org | with unsubscribe freebsd-questions-digest in the body of the message -- Everyone is a genius. It's just that some people are too stupid to realize it. PGP keyID 137AFD9E (C7DA 3350 1DEA F371 37DC D92A F0D4 C2ED 137A FD9E) To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20030210185635.GA694>