Date: Sat, 27 Dec 2003 12:59:46 -0500 From: "MikeM" <zlists@mgm51.com> To: freebsd-qa@freebsd.org Subject: 5.2RC2 - timeouts with tertiary IDE controller & CD-ROM Message-ID: <200312271259460479.00D97C93@sentry.24cl.home>
next in thread | raw e-mail | index | archive | help
Hopefully this is the correct list to post this on...
I have a Dell 600SC server that I use to store my MP3's. Whenever the
CD-ROM drive is plugged into the tertiary IDE controller I see timeouts
during the boot process. If I move the CD-ROM drive over to the secondary
IDE controller, everything works fine. FreeBSD 4.9 has no problems with
the CD-ROM plugged into the tertiary controller.
If I put the 5.2RC2 CD in the drive, the loader runs fine from the CD, but
the timeouts start occurring during the probe of all the devices. I cannot
post a 5.2RC2 dmesg because I don't know how to save it to disk from the
installer, and I cannot get past the installer. due to the CD read
timeouts.
However, I have installed 5.2RC1 with the CD-ROM on the secondary IDE
controller, and if I move the CD-ROM to the tertiary controller and try to
boot from the hard disk, I see the same time outs when the CD-ROM is
probed. The dmesg at the end of this message is the dmseg that I captured
under those circumstances.
This isn't a big problem for me because I can just move the CD-ROM to the
secondary controller, and everything seems to work fine. However, the Dell
server comes with the CD-ROM connected to the tertiary controller by
default, so the problem may effect others.
Let me know if you need more info. I have a little flexibility with the
server. Here's the [detailed logging] dmesg of 5.2RC1, the CD-ROM
connected to the tertiary controller, and booting off the hard disk. The
problems seem to start when the "ata4-master" section is hit:
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.2-RC #0: Mon Dec 22 13:11:59 EST 2003
mike@bigbox.24cl.home:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a33000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0a331f4.
Calibrating clock(s) ... i8254 clock: 1193372 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 2399337260 Hz
CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz (2399.34-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf27 Stepping = 7
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,M
CA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
real memory = 402587648 (383 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c29000 - 0x0000000017909fff, 382603264 bytes (93409 pages)
avail memory = 381374464 (363 MB)
Table 'FACP' at 0xfdca4
Table 'APIC' at 0xfdd18
MADT: Found table at 0xfdd18
MP Configuration Table version 1.4 found at 0xc00f0000
APIC: Using the MADT enumerator.
MADT: Found CPU APIC ID 0 ACPI ID 1: enabled
SMP: Added CPU 0 (AP)
MADT: Found CPU APIC ID 1 ACPI ID 2: disabled
MADT: Found CPU APIC ID 1 ACPI ID 3: disabled
MADT: Found CPU APIC ID 3 ACPI ID 4: disabled
ACPI APIC Table: <DELL PE600SC >
bios32: Found BIOS32 Service Directory header at 0xc00ffe80
bios32: Entry = 0xffe90 (c00ffe90) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xc71e
pnpbios: Found PnP BIOS data at 0xc00fe2d0
pnpbios: Entry = f0000:e2f4 Rev = 1.0
Other BIOS signatures found:
APIC: CPU 0 has ACPI ID 1
MADT: Found IO APIC ID 1, Vector 0 at 0xfec00000
ioapic0: Changing APIC ID to 1
ioapic0: intpin 0 -> ExtINT (edge, activehi)
ioapic0: intpin 1 -> irq 1 (edge, activehi)
ioapic0: intpin 2 -> irq 2 (edge, activehi)
ioapic0: intpin 3 -> irq 3 (edge, activehi)
ioapic0: intpin 4 -> irq 4 (edge, activehi)
ioapic0: intpin 5 -> irq 5 (edge, activehi)
ioapic0: intpin 6 -> irq 6 (edge, activehi)
ioapic0: intpin 7 -> irq 7 (edge, activehi)
ioapic0: intpin 8 -> irq 8 (edge, activehi)
ioapic0: intpin 9 -> irq 9 (edge, activehi)
ioapic0: intpin 10 -> irq 10 (edge, activehi)
ioapic0: intpin 11 -> irq 11 (edge, activehi)
ioapic0: intpin 12 -> irq 12 (edge, activehi)
ioapic0: intpin 13 -> irq 13 (edge, activehi)
ioapic0: intpin 14 -> irq 14 (edge, activehi)
ioapic0: intpin 15 -> irq 15 (edge, activehi)
MADT: Found IO APIC ID 2, Vector 16 at 0xfec01000
ioapic1: Changing APIC ID to 2
ioapic1: intpin 0 -> irq 16 (level, activelo)
ioapic1: intpin 1 -> irq 17 (level, activelo)
ioapic1: intpin 2 -> irq 18 (level, activelo)
ioapic1: intpin 3 -> irq 19 (level, activelo)
ioapic1: intpin 4 -> irq 20 (level, activelo)
ioapic1: intpin 5 -> irq 21 (level, activelo)
ioapic1: intpin 6 -> irq 22 (level, activelo)
ioapic1: intpin 7 -> irq 23 (level, activelo)
ioapic1: intpin 8 -> irq 24 (level, activelo)
ioapic1: intpin 9 -> irq 25 (level, activelo)
ioapic1: intpin 10 -> irq 26 (level, activelo)
ioapic1: intpin 11 -> irq 27 (level, activelo)
ioapic1: intpin 12 -> irq 28 (level, activelo)
ioapic1: intpin 13 -> irq 29 (level, activelo)
ioapic1: intpin 14 -> irq 30 (level, activelo)
ioapic1: intpin 15 -> irq 31 (level, activelo)
MADT: Found IO APIC ID 3, Vector 32 at 0xfec02000
ioapic2: Changing APIC ID to 3
ioapic2: intpin 0 -> irq 32 (level, activelo)
ioapic2: intpin 1 -> irq 33 (level, activelo)
ioapic2: intpin 2 -> irq 34 (level, activelo)
ioapic2: intpin 3 -> irq 35 (level, activelo)
ioapic2: intpin 4 -> irq 36 (level, activelo)
ioapic2: intpin 5 -> irq 37 (level, activelo)
ioapic2: intpin 6 -> irq 38 (level, activelo)
ioapic2: intpin 7 -> irq 39 (level, activelo)
ioapic2: intpin 8 -> irq 40 (level, activelo)
ioapic2: intpin 9 -> irq 41 (level, activelo)
ioapic2: intpin 10 -> irq 42 (level, activelo)
ioapic2: intpin 11 -> irq 43 (level, activelo)
ioapic2: intpin 12 -> irq 44 (level, activelo)
ioapic2: intpin 13 -> irq 45 (level, activelo)
ioapic2: intpin 14 -> irq 46 (level, activelo)
ioapic2: intpin 15 -> irq 47 (level, activelo)
lapic0: Routing NMI -> LINT1
lapic0: LINT1 trigger: edge
lapic0: LINT1 polarity: active-hi
MADT: Ignoring local NMI routed to ACPI CPU 2
MADT: Ignoring local NMI routed to ACPI CPU 3
MADT: Ignoring local NMI routed to ACPI CPU 4
ioapic0 <Version 1.1> irqs 0-15 on motherboard
ioapic1 <Version 1.1> irqs 16-31 on motherboard
ioapic2 <Version 1.1> irqs 32-47 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x00050014 LDR: 0x01000000 DFR: 0x0fffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
wlan: <802.11 Link Layer>
null: <null device, zero device>
random: <entropy source>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <DELL PE600SC > on motherboard
acpi0: Power Button (fixed)
ACPI timer looks BAD min = 3, max = 6, width = 3
ACPI timer looks BAD min = 3, max = 6, width = 3
ACPI timer looks BAD min = 3, max = 6, width = 3
ACPI timer looks BAD min = 3, max = 6, width = 3
ACPI timer looks BAD min = 3, max = 6, width = 3
ACPI timer looks BAD min = 3, max = 6, width = 3
ACPI timer looks BAD min = 3, max = 6, width = 3
ACPI timer looks BAD min = 3, max = 6, width = 3
ACPI timer looks BAD min = 3, max = 6, width = 3
ACPI timer looks BAD min = 3, max = 6, width = 3
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
pci_open(1): mode 1 addr port (0x0cf8) is 0x800078ac
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=00171166)
pcibios: BIOS version 2.10
Using $PIR table, 7 entries at 0xc00fc320
PCI-Only Interrupts: none
Location Bus Device Pin Link IRQs
embedded 0 2 A 0x61 3 4 5 6 7 10
embedded 0 15 A 0x81 3 4 5 6 7 10
slot 1 0 3 A 0x6b 3 4 5 6 7 10
slot 1 0 3 B 0x6c 3 4 5 6 7 10
slot 1 0 3 C 0x6b 3 4 5 6 7 10
slot 1 0 3 D 0x6c 3 4 5 6 7 10
slot 2 0 4 A 0x69 3 4 5 6 7 10
slot 2 0 4 B 0x6a 3 4 5 6 7 10
slot 2 0 4 C 0x69 3 4 5 6 7 10
slot 2 0 4 D 0x6a 3 4 5 6 7 10
slot 3 0 5 A 0x67 3 4 5 6 7 10
slot 3 0 5 B 0x68 3 4 5 6 7 10
slot 3 0 5 C 0x67 3 4 5 6 7 10
slot 3 0 5 D 0x68 3 4 5 6 7 10
slot 4 0 6 A 0x64 3 4 5 6 7 10
slot 4 0 6 B 0x66 3 4 5 6 7 10
slot 4 0 6 C 0x64 3 4 5 6 7 10
slot 4 0 6 D 0x66 3 4 5 6 7 10
slot 5 0 7 A 0x62 3 4 5 6 7 10
slot 5 0 7 B 0x63 3 4 5 6 7 10
slot 5 0 7 C 0x62 3 4 5 6 7 10
slot 5 0 7 D 0x63 3 4 5 6 7 10
AcpiOsDerivePciId: bus 0 dev 0 func 0
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_cpu1: <CPU> on acpi0
device_probe_and_attach: acpi_cpu1 attach returned 6
pcib0: <ACPI Host-PCI bridge> on acpi0
---- initial configuration ------------------------
\\_SB_.LUSB irq 0: [ 3 4 5 6 7 10 12] low,level,sharable 0.15.0
\\_SB_.LTID irq 11: [ 11] low,level,sharable 0.14.0
---- before setting priority for links ------------
\\_SB_.LUSB:
interrupts: 3 4 5 6 7 10 12
penalty: 1110 1110 110 1110 1110 110 1110
references: 1
priority: 0
---- before fixup boot-disabled links -------------
\\_SB_.LUSB:
interrupts: 3 4 5 6 7 10 12
penalty: 1110 1110 110 1110 1110 110 1110
references: 1
priority: 824
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\\_SB_.LUSB irq 10: [ 3 4 5 6 7 10 12] low,level,sharable 0.15.0
\\_SB_.LTID irq 11: [ 11] low,level,sharable 0.14.0
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x1166, dev=0x0017, revid=0x32
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1166, dev=0x0017, revid=0x00
bus=0, slot=0, func=1
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 1, range 32, base fe900000, size 17, enabled
map[18]: type 4, range 32, base 0000ecc0, size 6, enabled
pcib0: matched entry for 0.2.INTA (source )
pcib0: device is hardwired to IRQ 17
found-> vendor=0x8086, dev=0x100e, revid=0x02
bus=0, slot=2, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0230, cachelnsz=16 (dwords)
lattimer=0x20 (960 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns)
intpin=a, irq=17
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type 4, range 32, base 0000ecb0, size 4, enabled
map[14]: type 1, range 32, base fe925000, size 4, enabled
map[18]: type 1, range 32, base fe000000, size 23, enabled
pcib0: matched entry for 0.6.INTA (source )
pcib0: device is hardwired to IRQ 25
found-> vendor=0x13c1, dev=0x1001, revid=0x01
bus=0, slot=6, func=0
class=01-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x011f, statreg=0x0290, cachelnsz=16 (dwords)
lattimer=0x20 (960 ns), mingnt=0x09 (2250 ns), maxlat=0x00 (0 ns)
intpin=a, irq=25
powerspec 1 supports D0 D1 D3 current D0
map[10]: type 4, range 32, base 0000eca8, size 3, enabled
map[14]: type 4, range 32, base 0000eca0, size 2, enabled
map[18]: type 4, range 32, base 0000ec90, size 3, enabled
map[1c]: type 4, range 32, base 0000ec88, size 2, enabled
map[20]: type 4, range 32, base 0000ec70, size 4, enabled
map[24]: type 1, range 32, base fe920000, size 14, enabled
pcib0: matched entry for 0.7.INTA (source )
pcib0: device is hardwired to IRQ 27
found-> vendor=0x105a, dev=0x4d69, revid=0x02
bus=0, slot=7, func=0
class=01-80-85, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0430, cachelnsz=16 (dwords)
lattimer=0x20 (960 ns), mingnt=0x04 (1000 ns), maxlat=0x12 (4500 ns)
intpin=a, irq=27
powerspec 1 supports D0 D1 D3 current D0
map[10]: type 1, range 32, base fd000000, size 24, enabled
map[14]: type 4, range 32, base 0000e800, size 8, enabled
map[18]: type 1, range 32, base fe924000, size 12, enabled
found-> vendor=0x1002, dev=0x4752, revid=0x27
bus=0, slot=8, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x00a7, statreg=0x0290, cachelnsz=16 (dwords)
lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 000001e8, size 3, enabled
map[14]: type 4, range 32, base 000003ec, size 2, enabled
map[18]: type 4, range 32, base 00000168, size 3, enabled
map[1c]: type 4, range 32, base 0000036c, size 2, enabled
map[20]: type 4, range 32, base 00000900, size 4, enabled
pcib0: matched entry for 0.14.INTA (source \\_SB_.LTID)
pcib0: slot 14 INTA is routed to irq 11
found-> vendor=0x1166, dev=0x0217, revid=0xa0
bus=0, slot=14, func=0
class=01-01-87, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0200, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
found-> vendor=0x1166, dev=0x0203, revid=0xa0
bus=0, slot=15, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0147, statreg=0x2200, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 4, range 32, base 000001f0, size 3, enabled
map[14]: type 4, range 32, base 000003f4, size 2, enabled
map[18]: type 4, range 32, base 00000170, size 3, enabled
map[1c]: type 4, range 32, base 00000374, size 2, enabled
map[20]: type 4, range 32, base 000008b0, size 4, enabled
found-> vendor=0x1166, dev=0x0213, revid=0xa0
bus=0, slot=15, func=1
class=01-01-8a, hdrtype=0x00, mfdev=1
cmdreg=0x0145, statreg=0x0200, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1166, dev=0x0227, revid=0x00
bus=0, slot=15, func=3
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0144, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.19> port
0xecc0-0xecff mem 0xfe900000-0xfe91ffff irq 17 at device 2.0 on pci0
em0: bpf attached
em0: Speed:N/A Duplex:N/A
twe0: <3ware 7000 series Storage Controller. Driver version 1.50.00.000>
port 0xecb0-0xecbf mem 0xfe000000-0xfe7fffff,0xfe925000-0xfe92500f irq 25
at device 6.0 on pci0
twe0: AEN: <soft reset>
twe0: 4 ports, Firmware FE7X 1.05.00.036, BIOS BE7X 1.08.00.044
twe0: Monitor ME7X 1.01.00.035, PCB Rev3 , Achip V3.20 , Pchip V1.30
twe0: port 0: Maxtor 6Y160P0 156334MB
twe0: port 1: Maxtor 6Y160P0 156334MB
twe0: port 2: Maxtor 6Y160P0 156334MB
atapci0: <Promise PDC20269 UDMA133 controller> port
0xec70-0xec7f,0xec88-0xec8b,0xec90-0xec97,0xeca0-0xeca3,0xeca8-0xecaf mem
0xfe920000-0xfe923fff irq 27 at device 7.0 on pci0
atapci0: [MPSAFE]
ata2: reset tp1 mask=03 ostat0=50 ostat1=00
ata2-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata2-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata2: reset tp2 mask=03 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata2: at 0xeca8 on atapci0
ata2: [MPSAFE]
ata3: reset tp1 mask=03 ostat0=20 ostat1=30
ata3-master: stat=0x20 err=0x20 lsb=0x20 msb=0x20
ata3-slave: stat=0x30 err=0x30 lsb=0x30 msb=0x30
ata3: reset tp2 mask=03 stat0=20 stat1=30 devices=0x0
ata3: at 0xec90 on atapci0
ata3: [MPSAFE]
pci0: <display, VGA> at device 8.0 (no driver attached)
atapci1: <ServerWorks CSB6 UDMA66 controller> port
0x900-0x90f,0x36c-0x36f,0x168-0x16f,0x3ec-0x3ef,0x1e8-0x1ef irq 11 at
device 14.0 on pci0
atapci1: [MPSAFE]
ata4: reset tp1 mask=03 ostat0=50 ostat1=00
ata4-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata4-slave: stat=0x00 err=0x04 lsb=0x00 msb=0x00
ata4: reset tp2 mask=03 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER>
ata4: at 0x1e8 on atapci1
ata4: [MPSAFE]
ata5: simplex device, DMA on primary only
ata5: at 0x168 on atapci1
ata5: [MPSAFE]
atapci2: <ServerWorks CSB6 UDMA100 controller> port
0x8b0-0x8bf,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 at device 15.1
on pci0
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 mask=03 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: at 0x1f0 irq 14 on atapci2
ata0: [MPSAFE]
ata1: at 0x170 irq 15 on atapci2
ata1: [MPSAFE]
isab0: <PCI-ISA bridge> at device 15.3 on pci0
isa0: <ISA bus> on isab0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: unable to allocate IRQ
psmcpnp0 irq 12 on acpi0
psm0: current command byte:0065
psm0: failed to reset the aux device.
sio0: irq maps: 0x2001 0x2011 0x2001 0x2001
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
ppc0: using extended I/O port range
ppc0: ECP SPP SPP
ppc0 port 0x778-0x77f,0x378-0x37f irq 7 drq 1 on acpi0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
acpi_cpu1: <CPU> on acpi0
device_probe_and_attach: acpi_cpu1 attach returned 6
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sio: sio0 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
ex_isa_identify()
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem
0xec000-0xeffff,0xc9800-0xcbfff,0xc8000-0xc8fff,0xc0000-0xc7fff on isa0
pmtimer0 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
fdc0 failed to probe at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0x2081 0x2081 0x2081 0x2081
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 2399337260 Hz quality 800
Timecounters tick every 10.000 msec
lo0: bpf attached
ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ata0-master: setting PIO4 on ServerWorks CSB6 chip
ata0-master: setting UDMA100 on ServerWorks CSB6 chip
GEOM: create disk ad0 dp=0xc3afee60
ad0: <ST380021A/3.75> ATA-5 disk at ata0-master
ad0: 76293MB (156250000 sectors), 155009 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA100
GEOM: new disk ad0
ar: FreeBSD check1 failed
ata2-master: pio=0x0c wdma=0x22 udma=0x46 cable=80pin
ata2-master: setting PIO4 on Promise PDC20269 chip
ata2-master: setting UDMA133 on Promise PDC20269 chip
GEOM: create disk ad4 dp=0xc3b96b60
ad4: <Maxtor 5A300J0/RAMB1TV0> ATA-7 disk at ata2-master
ad4: 286103MB (585940320 sectors), 581290 C, 16 H, 63 S, 512 B
ad4: 16 secs/int, 1 depth queue, UDMA133
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:156248127
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad0s1, start 32256 length 79999041024 end 79999073279
GEOM: new disk ad4
GEOM: Configure ad0s1a, start 0 length 1073741824 end 1073741823
GEOM: Configure ad0s1b, start 1073741824 length 1073741824 end 2147483647
GEOM: Configure ad0s1c, start 0 length 79999041024 end 79999041023
GEOM: Configure ad0s1d, start 2147483648 length 2147483648 end 4294967295
GEOM: Configure ad0s1e, start 4294967296 length 2147483648 end 6442450943
GEOM: Configure ad0s1f, start 6442450944 length 73556590080 end 79999041023
ar: Promise check1 failed
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:585938682
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad4s1, start 32256 length 300000605184 end 300000637439
GEOM: Configure ad4s1c, start 0 length 300000605184 end 300000605183
GEOM: Configure ad4s1e, start 0 length 300000605184 end 300000605183
ata5: spurious interrupt - status=0xff error=0xff
ata4-master: pio=0x0c wdma=0x22 udma=0x42 cable=40pin
ata4-master: timeout sending command=ef
ata4-master: error issueing PIO command
ata4-master: FAILURE setting PIO4 on ServerWorks CSB6 chip
acd0: timeout sending command=a0
acd0: error issuing ATA PACKET command
acd0: timeout sending command=a0
acd0: error issuing ATA PACKET command
acd0: timeout sending command=a0
acd0: error issuing ATA PACKET command
acd0: timeout sending command=a0
acd0: error issuing ATA PACKET command
acd0: timeout sending command=a0
acd0: error issuing ATA PACKET command
acd0: <GCR-8481B/2.01> CDROM drive at ata4 as master
acd0: BIOSPIO
acd0: Reads:
acd0: Writes:
acd0: Mechanism: caddy
acd0: Medium: CD-ROM unknown
twed0: <Unit 0, RAID5, Normal> on twe0
twed0: 312667MB (640342016 sectors)
GEOM: create disk twed0 dp=0xc3b7688c
ioapic0: routing intpin 1 (IRQ 1) to cluster 0
ioapic0: routing intpin 4 (IRQ 4) to cluster 0
ioapic0: routing intpin 7 (IRQ 7) to cluster 0
ioapic0: routing intpin 8 (IRQ 8) to cluster 0
ioapic0: routing intpin 9 (IRQ 9) to cluster 0
ioapic0: routing intpin 11 (IRQ 11) to cluster 0
ioapic0: routing intpin 13 (IRQ 13) to cluster 0
ioapic0: routing intpin 14 (IRQ 14) to cluster 0
ioapic0: routing intpin 15 (IRQ 15) to cluster 0
ioapic1: routing intpin 1 (IRQ 17) to cluster 0
ioapic1: routing intpin 9 (IRQ 25) to cluster 0
ioapic1: routing intpin 11 (IRQ 27) to cluster 0
GEOM: new disk twed0
acd0: timeout sending command=a0
acd0: error issuing ATA PACKET command
acd0: timeout sending command=a0
acd0: error issuing ATA PACKET command
acd0: timeout sending command=a0
acd0: error issuing ATA PACKET command
acd0: timeout sending command=a0
acd0: error issuing ATA PACKET command
acd0: timeout sending command=a0
acd0: error issuing ATA PACKET command
acd0: timeout sending command=a0
acd0: error issuing ATA PACKET command
acd0: timeout sending command=a0
acd0: error issuing ATA PACKET command
acd0: timeout sending command=a0
acd0: error issuing ATA PACKET command
acd0: timeout sending command=a0
acd0: error issuing ATA PACKET command
acd0: timeout sending command=a0
acd0: error issuing ATA PACKET command
acd0: timeout sending command=a0
acd0: error issuing ATA PACKET command
acd0: timeout sending command=a0
acd0: error issuing ATA PACKET command
acd0: timeout sending command=a0
acd0: error issuing ATA PACKET command
acd0: timeout sending command=a0
acd0: error issuing ATA PACKET command
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:640334772
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure twed0s1, start 32256 length 327851403264 end 327851435519
GEOM: Configure twed0s1c, start 0 length 327851403264 end 327851403263
GEOM: Configure twed0s1e, start 0 length 327851403264 end 327851403263
Mounting root from ufs:/dev/ad0s1a
start_init: trying /sbin/init
em0: Link is up 1000 Mbps Full Duplex
[finis]
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200312271259460479.00D97C93>