Date: Thu, 18 Mar 2004 11:43:47 -0500 From: Christopher Sean Hilton <chris@vindaloo.com> To: freebsd-stable@freebsd.org Cc: julian@elischer.org Subject: Re: HEADSUP!!! USB MFC committed Message-ID: <20040318164347.GA681@endaba.pvt.vindaloo.com> In-Reply-To: <20040316094843.7F08840822@fw.farid-hajji.net> References: <Pine.BSF.4.21.0403141401220.7997-100000@InterJet.elischer.org> <20040316094843.7F08840822@fw.farid-hajji.net>
next in thread | previous in thread | raw e-mail | index | archive | help
Summary:
This is probably too old a datapoint but...
I just updated my kernel to last Tuesday's version of 4.9-STABLE.
Good:
My USB mouse works as expected.
My USB hard drive works correctly.
No change:
My Olympus C-2100Z USB camera incorrectly comes up under the ugen driver rather
than the umass driver.
My Handspring Treo 300 comes up under the ugen driver rather than
the visor driver. I have not honestly spent the time needed to
get this device working under FreeBSD. Nuf said.
Bad:
My Memorex USB pendrive probes correctly if installed at boot
time but hangs the USB bus if installed after boot.
Details:
Logitech Mouse:
Mar 18 11:19:23 endaba /kernel: ums0: Logitech USB Receiver, rev 1.10/9.10, addr 3, iclass 3/1
Mar 18 11:19:23 endaba /kernel: ums0: 5 buttons and Z dir.
Generic USB Hard drive:
Mar 18 11:29:43 endaba /kernel: umass0: Genesys Logic USB TO IDE, rev 2.00/0.02, addr 4
Mar 18 11:29:43 endaba /kernel: da0 at umass-sim0 bus 0 target 0 lun 0
Mar 18 11:29:43 endaba /kernel: da0: <IC25N020 ATCS05-0 0811> Fixed Direct Access SCSI-0 device
Mar 18 11:29:43 endaba /kernel: da0: 650KB/s transfers
Mar 18 11:29:43 endaba /kernel: da0: 19077MB (39070080 512 byte sectors: 64H 32S/T 19077C)
Camera:
Mar 18 11:30:34 endaba /kernel: ugen0: OLYMPU C-2100 Ultra Zoom, rev 1.10/1.00, addr 4
Handsprint Treo 300:
Mar 18 11:31:52 endaba /kernel: ugen0: Handspring Handspring Visor, rev 1.00/1.00, addr 4
Pen Drive at boot time:
Mar 18 10:44:58 endaba /kernel: umass0: USB Solid state disk, rev 1.10/1.00, addr 3
Mar 18 10:44:58 endaba /kernel: ums0: Logitech USB Receiver, rev 1.10/9.10, addr 4, iclass
3/1
Mar 18 10:44:58 endaba /kernel: ums0: 5 buttons and Z dir.
...
Mar 18 10:44:58 endaba /kernel: da0 at umass-sim0 bus 0 target 0 lun 0
Mar 18 10:44:58 endaba /kernel: da0: <Memorex ThumbDrive 1.12> Removable Direct Access SCSI-2 device
Mar 18 10:44:58 endaba /kernel: da0: 650KB/s transfers
Mar 18 10:44:58 endaba /kernel: da0: 252MB (516096 512 byte sectors: 64H 32S/T 252C)
Pen Drive after boot:
Mar 18 11:35:27 endaba /kernel: umass0: USB Solid state disk, rev 1.10/1.00, addr 4
Mar 18 11:35:27 endaba /kernel: ums0: at uhub1 port 4 (addr 3) disconnected
Mar 18 11:35:27 endaba /kernel: ums0: detached
Mar 18 11:35:27 endaba moused: unable to open /dev/ums0: Device not configured
Note that at this point plugging in the Pen Drive disconnected my usb mouse.
Mar 18 11:35:39 endaba /kernel: ums0: Logitech USB Receiver, rev 1.10/9.10, addr 3, iclass 3/1
Mar 18 11:35:39 endaba /kernel: ums0: 5 buttons and Z dir.
My mouse tries to reconnect periodically but it always fails.
Mar 18 11:35:39 endaba /kernel: ums0: at uhub1 port 4 (addr 3) disconnected
Mar 18 11:35:39 endaba /kernel: ums0: detached
Mar 18 11:35:39 endaba moused: unable to open /dev/ums0: Device not configured
The mouse again.
Mar 18 11:35:40 endaba /kernel: ums0: Logitech USB Receiver, rev 1.10/9.10, addr 3, iclass 3/1
Mar 18 11:35:40 endaba /kernel: ums0: 5 buttons and Z dir.
Mar 18 11:35:40 endaba /kernel: ums0: at uhub1 port 4 (addr 3) disconnected
Mar 18 11:35:40 endaba /kernel: ums0: detached
Mar 18 11:35:40 endaba moused: unable to open /dev/ums0: Device not configured
After a minute or so I unplug the Pen drive.
Mar 18 11:36:29 endaba /kernel: umass0: BBB reset failed, STALLED
Mar 18 11:36:29 endaba /kernel: umass0: BBB bulk-in clear stall failed, STALLED
Mar 18 11:36:29 endaba /kernel: umass0: BBB bulk-out clear stall failed, STALLED
Mar 18 11:36:29 endaba /kernel: umass0: BBB reset failed, STALLED
Mar 18 11:36:29 endaba /kernel: umass0: BBB bulk-in clear stall failed, STALLED
Mar 18 11:36:29 endaba /kernel: umass0: BBB bulk-out clear stall failed, STALLED
Mar 18 11:36:29 endaba /kernel: umass0: BBB reset failed, STALLED
Mar 18 11:36:29 endaba /kernel: umass0: BBB bulk-in clear stall failed, STALLED
Mar 18 11:36:29 endaba /kernel: umass0: BBB bulk-out clear stall failed, STALLED
Mar 18 11:36:29 endaba /kernel: umass0: BBB reset failed, STALLED
Mar 18 11:36:29 endaba /kernel: umass0: BBB bulk-in clear stall failed, STALLED
Mar 18 11:36:29 endaba /kernel: umass0: BBB bulk-out clear stall failed, STALLED
Mar 18 11:36:29 endaba /kernel: umass0: BBB reset failed, STALLED
Mar 18 11:36:29 endaba /kernel: umass0: BBB bulk-in clear stall failed, STALLED
Mar 18 11:36:29 endaba /kernel: umass0: BBB bulk-out clear stall failed, STALLED
Mar 18 11:36:29 endaba /kernel: umass0: at uhub0 port 1 (addr 4) disconnected
Mar 18 11:36:29 endaba /kernel: umass0: detached
And the mouse comes back normally.
Mar 18 11:36:44 endaba /kernel: ums0: Logitech USB Receiver, rev 1.10/9.10, addr 3, iclass 3/1
Mar 18 11:36:44 endaba /kernel: ums0: 5 buttons and Z dir.
--
Chris Hilton chilton-at-vindaloo-dot-com
------------------------------------------------------------------------
"All I was doing was trying to get home from work!"
-- Rosa Parks
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20040318164347.GA681>