Date: Tue, 26 Dec 2006 18:08:08 -0800 From: Mario Theodoridis <mario@schmut.com> To: freebsd-isp@freebsd.org Cc: Tim McCullagh <tim@halenet.com.au>, FreeBSD Hackers <FreeBSD-Hackers@freebsd.org>, Jan Knepper <jan@digitaldaemon.com> Subject: Re: 6.1-RELEASE / 6.2 Kernel Crash... Message-ID: <200612261808.08984.mario@schmut.com> In-Reply-To: <4591CB3C.1060902@digitaldaemon.com> References: <45918F6E.90006@digitaldaemon.com> <004c01c7293b$d5e03b40$6500a8c0@laptopt> <4591CB3C.1060902@digitaldaemon.com>
next in thread | previous in thread | raw e-mail | index | archive | help
is it just me, or is this beginning to sound like hardware problems? mario;> On Tuesday 26 December 2006 17:24, Jan Knepper wrote: > Tried that and started > > dd if=/dev/ad4 if=/dev/ad6 bs=1m > > Kernel went in panic and automatic reboot in about an hour... <sigh> > > It gets worse... when it does reboot the disk drive will not show in the > BIOS, nor does FreeBSD recognize it during boot. The system actually has > to be turned off to reset the drive... > > This is bad... > > Any other suggestions? > > Thanks! > Jan > > Tim McCullagh wrote: > > Hi Jan > > > > try editing your loader.conf > > > > I had a similar sounding issue. As soon as I did the following the > > system became stable immediately. It was also on a Tyan Mainboard, > > although with dual Xeon's > > > > # vi /boot/loader.conf > > hint.apic.0.disabled="1" > > > > > > Regards > > > > Tim > > ----- Original Message ----- From: "Jan Knepper" <jan@digitaldaemon.com> > > To: "FreeBSD ISP" <FreeBSD-ISP@FreeBSD.org>; "FreeBSD Hackers" > > <FreeBSD-Hackers@FreeBSD.org> > > Sent: Wednesday, December 27, 2006 7:09 AM > > Subject: 6.1-RELEASE / 6.2 Kernel Crash... > > > >> All, (sorry for the cross post) > >> > >> Something goofy is going on with a 6.x kernel. > >> > >> Dual Opteron Server (Tyan motherboard). 2 GB RAM... 2 x 256 GB SATA > >> HD's. > >> Just upgraded this machine from FreeBSD 5.5-STABLE to 6.2RC# and than > >> down to 6.1-RELEASE. > >> For some reason FreeBSD 6.1 seems to be very unstable. I use a custom > >> kernel, (most devices not present in the system have been removed). > >> > >> When I create an SMP kernel after an undefined about of time which I > >> have seen varying from 5 minutes up to about 6 hours the kernel will > >> just hang. Things that seem to accelerate/aggrevate this are running > >> CVSup from a repository on the same system. > >> Something else that seems to push it is dd if=/dev/ad4 if=/dev/ad6 > >> bs=64m (copying the master disk to the supposed slave, however geom > >> is not active and module geom_mirror is not loaded! > >> > >> When I take SMP out of the kernel config and rebuild and install > >> instead of hanging, the system seems to crash and reboot when I > >> perform the same action. > >> > >> Also... When I first upgraded I did get an error during boot: > >> kernel: module_register_init: MOD_LOAD (amr_linux, > >> 0xffffffff805db120, 0) error 6 > >> I disabled device amr (under RAID controllers) in the kernel config > >> which took care of this. > >> > >> Following the bootlog. If any of you had any idea what the problem > >> might be I definitely would like to know. > >> > >> Thanks! > >> Jan > >> > >> > >> > >> syslogd: kernel boot file is /boot/kernel/kernel > >> kernel: Copyright (c) 1992-2006 The FreeBSD Project. > >> kernel: Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, > >> 1993, 1994 > >> kernel: The Regents of the University of California. All rights > >> reserved. > >> kernel: FreeBSD 6.1-RELEASE #4: Tue Dec 26 12:03:35 EST 2006 > >> kernel: root@digitaldaemon.com:/usr/src/sys/amd64/compile/digitaldaemon > >> kernel: Timecounter "i8254" frequency 1193182 Hz quality 0 > >> kernel: CPU: AMD Opteron(tm) Processor 246 (1993.53-MHz K8-class CPU) > >> kernel: Origin = "AuthenticAMD" Id = 0xf5a Stepping = 10 > >> kernel: > >> Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE, > >>MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2> > >> > >> kernel: AMD Features=0xe0500800<SYSCALL,NX,MMX+,LM,3DNow+,3DNow> > >> kernel: real memory = 2147418112 (2047 MB) > >> kernel: avail memory = 2065596416 (1969 MB) > >> kernel: ACPI APIC Table: <A M I OEMAPIC > > >> kernel: FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs > >> kernel: cpu0 (BSP): APIC ID: 0 > >> kernel: cpu1 (AP): APIC ID: 1 > >> kernel: MADT: Forcing active-low polarity and level trigger for SCI > >> kernel: ioapic0 <Version 1.1> irqs 0-23 on motherboard > >> kernel: ioapic1 <Version 1.1> irqs 24-27 on motherboard > >> kernel: ioapic2 <Version 1.1> irqs 28-31 on motherboard > >> kernel: netsmb_dev: loaded > >> kernel: acpi0: <A M I OEMRSDT> on motherboard > >> kernel: acpi0: Power Button (fixed) > >> kernel: Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 > >> kernel: acpi_timer0: <24-bit timer at 3.579545MHz> port 0x5008-0x500b > >> on acpi0 > >> kernel: cpu0: <ACPI CPU> on acpi0 > >> kernel: acpi_throttle0: <ACPI CPU Throttling> on cpu0 > >> kernel: cpu1: <ACPI CPU> on acpi0 > >> kernel: pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > >> kernel: pci0: <ACPI PCI bus> on pcib0 > >> kernel: pcib1: <ACPI PCI-PCI bridge> at device 6.0 on pci0 > >> kernel: pci3: <ACPI PCI bus> on pcib1 > >> kernel: ohci0: <OHCI (generic) USB controller> mem > >> 0xff3fd000-0xff3fdfff irq 19 at device 0.0 on pci3 > >> kernel: ohci0: [GIANT-LOCKED] > >> kernel: usb0: OHCI version 1.0, legacy support > >> kernel: usb0: <OHCI (generic) USB controller> on ohci0 > >> kernel: usb0: USB revision 1.0 > >> kernel: uhub0: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > >> kernel: uhub0: 3 ports with 3 removable, self powered > >> kernel: ohci1: <OHCI (generic) USB controller> mem > >> 0xff3fe000-0xff3fefff irq 19 at device 0.1 on pci3 > >> kernel: ohci1: [GIANT-LOCKED] > >> kernel: usb1: OHCI version 1.0, legacy support > >> kernel: usb1: <OHCI (generic) USB controller> on ohci1 > >> kernel: usb1: USB revision 1.0 > >> kernel: uhub1: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > >> kernel: uhub1: 3 ports with 3 removable, self powered > >> kernel: xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0x8080-0x80ff > >> mem 0xff3ff800-0xff3ff87f irq 16 at device 10.0 on pci3 > >> kernel: miibus0: <MII bus> on xl0 > >> kernel: ukphy0: <Generic IEEE 802.3u media interface> on miibus0 > >> kernel: ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > >> kernel: xl0: Ethernet address: 00:04:75:ad:ac:0a > >> kernel: atapci0: <SiI 3114 SATA150 controller> port > >> 0x8c00-0x8c07,0x8880-0x8883,0x8800-0x8807,0x8480-0x8483,0x8400-0x840f > >> mem 0xff3ffc00-0xff3fffff irq 17 at device 11.0 on pci3 > >> kernel: ata2: <ATA channel 0> on atapci0 > >> kernel: ata3: <ATA channel 1> on atapci0 > >> kernel: ata4: <ATA channel 2> on atapci0 > >> kernel: ata5: <ATA channel 3> on atapci0 > >> kernel: fwohci0: <Texas Instruments TSB43AB22/A> mem > >> 0xff3ff000-0xff3ff7ff,0xff3f8000-0xff3fbfff irq 19 at device 12.0 on > >> pci3 > >> kernel: fwohci0: OHCI version 1.10 (ROM=1) > >> kernel: fwohci0: No. of Isochronous channels is 4. > >> kernel: fwohci0: EUI64 00:e0:81:00:00:30:4c:06 > >> kernel: fwohci0: Phy 1394a available S400, 2 ports. > >> kernel: fwohci0: Link S400, max_rec 2048 bytes. > >> kernel: firewire0: <IEEE1394(FireWire) bus> on fwohci0 > >> kernel: fwe0: <Ethernet over FireWire> on firewire0 > >> kernel: if_fwe0: Fake Ethernet address: 02:e0:81:30:4c:06 > >> kernel: fwe0: Ethernet address: 02:e0:81:30:4c:06 > >> kernel: fwe0: if_start running deferred for Giant > >> kernel: sbp0: <SBP-2/SCSI over FireWire> on firewire0 > >> kernel: fwohci0: Initiate bus reset > >> kernel: fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode > >> kernel: firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) > >> kernel: firewire0: bus manager 0 (me) > >> kernel: isab0: <PCI-ISA bridge> at device 7.0 on pci0 > >> kernel: isa0: <ISA bus> on isab0 > >> kernel: atapci1: <AMD 8111 UDMA133 controller> port > >> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 7.1 on pci0 > >> kernel: ata0: <ATA channel 0> on atapci1 > >> kernel: ata1: <ATA channel 1> on atapci1 > >> kernel: pci0: <serial bus, SMBus> at device 7.2 (no driver attached) > >> kernel: pci0: <bridge> at device 7.3 (no driver attached) > >> kernel: pci0: <multimedia, audio> at device 7.5 (no driver attached) > >> kernel: pcib2: <ACPI PCI-PCI bridge> at device 10.0 on pci0 > >> kernel: pci2: <ACPI PCI bus> on pcib2 > >> kernel: bge0: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> > >> mem 0xff1f0000-0xff1fffff irq 24 at device 9.0 on pci2 > >> kernel: miibus1: <MII bus> on bge0 > >> kernel: brgphy0: <BCM5703 10/100/1000baseTX PHY> on miibus1 > >> kernel: brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, > >> 1000baseTX, 1000baseTX-FDX, auto > >> kernel: bge0: Ethernet address: 00:e0:81:2d:ee:f7 > >> kernel: pci0: <base peripheral, interrupt controller> at device 10.1 > >> (no driver attached) > >> kernel: pcib3: <ACPI PCI-PCI bridge> at device 11.0 on pci0 > >> kernel: pci1: <ACPI PCI bus> on pcib3 > >> kernel: pci0: <base peripheral, interrupt controller> at device 11.1 > >> (no driver attached) > >> kernel: pcib4: <ACPI Host-PCI bridge> on acpi0 > >> kernel: pci4: <ACPI PCI bus> on pcib4 > >> kernel: pcib5: <ACPI PCI-PCI bridge> at device 1.0 on pci4 > >> kernel: pci5: <ACPI PCI bus> on pcib5 > >> kernel: pci5: <display, VGA> at device 0.0 (no driver attached) > >> kernel: pci5: <display> at device 0.1 (no driver attached) > >> kernel: acpi_button0: <Power Button> on acpi0 > >> kernel: atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 > >> on acpi0 > >> kernel: atkbd0: <AT Keyboard> irq 1 on atkbdc0 > >> kernel: kbd0 at atkbd0 > >> kernel: atkbd0: [GIANT-LOCKED] > >> kernel: psm0: <PS/2 Mouse> irq 12 on atkbdc0 > >> kernel: psm0: [GIANT-LOCKED] > >> kernel: psm0: model IntelliMouse Explorer, device ID 4 > >> kernel: sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 > >> flags 0x10 on acpi0 > >> kernel: sio0: type 16550A > >> kernel: sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on > >> acpi0 > >> kernel: sio1: type 16550A > >> kernel: fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 > >> irq 6 drq 2 on acpi0 > >> kernel: fdc0: [FAST] > >> kernel: ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 > >> on acpi0 > >> kernel: ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode > >> kernel: ppbus0: <Parallel port bus> on ppc0 > >> kernel: orm0: <ISA Option ROMs> at iomem > >> 0xc0000-0xccfff,0xcd000-0xd17ff,0xd1800-0xd1fff,0 > >> xd2000-0xd2fff on isa0 > >> kernel: sc0: <System console> at flags 0x100 on isa0 > >> kernel: sc0: VGA <16 virtual consoles, flags=0x300> > >> kernel: vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem > >> 0xa0000-0xbffff on isa0 > >> kernel: ugen0: American Power Conversion Back-UPS RS 1500 FW:8.g9 .D > >> USB FW:g9, rev 1.10/1.06, addr 2 > >> kernel: Timecounters tick every 1.000 msec > >> kernel: ipfw2 (+ipv6) initialized, divert loadable, rule-based > >> forwarding enabled, default to deny, logging limited to 100 > >> packets/entry by default > >> kernel: acd0: DVDR <NEC DVD RW ND-3520A/1.04> at ata0-master UDMA33 > >> kernel: ad4: 238475MB <HDS722525VLSA80 V36OA6MA> at ata2-master SATA150 > >> kernel: ad6: 238475MB <HDS722525VLSA80 V36OA6MA> at ata3-master SATA150 > >> kernel: SMP: AP CPU #1 Launched! > >> kernel: Trying to mount root from ufs:/dev/ad4s1a > >> > >> _______________________________________________ > >> freebsd-isp@freebsd.org mailing list > >> http://lists.freebsd.org/mailman/listinfo/freebsd-isp > >> To unsubscribe, send any mail to "freebsd-isp-unsubscribe@freebsd.org" > > > > _______________________________________________ > > freebsd-isp@freebsd.org mailing list > > http://lists.freebsd.org/mailman/listinfo/freebsd-isp > > To unsubscribe, send any mail to "freebsd-isp-unsubscribe@freebsd.org" > > _______________________________________________ > freebsd-isp@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-isp > To unsubscribe, send any mail to "freebsd-isp-unsubscribe@freebsd.org"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200612261808.08984.mario>