Date: Tue, 05 May 2009 02:48:00 -0700 From: Chris H <chris#@1command.com> To: freebsd-stable@freebsd.org Subject: GEOM_STRIPE: Cannot add disk da2c to st0 (error=17). Message-ID: <20090505024800.tk0saqntsgk8kk8c@webmail.1command.com>
next in thread | raw e-mail | index | archive | help
Greetings, I'm attempting to upgrade one of our servers to 6.4 (from 6.2) Before doing so I need to stripe 3 identical drives on the same SCSI port into one drive, the drives are on an LSI controller with 2 ports: May 5 02:10:15 hitme kernel: sym0: <1010-66> port 0xe400-0xe4ff mem 0xfebe0000-0xfebe03ff,0xfebd8000-0xfebd9fff irq 29 at device 6.0 on pci1 May 5 02:10:15 hitme kernel: sym0: Reserved 0x400 bytes for rid 0x14 type 3 at 0xfebe0000 May 5 02:10:15 hitme kernel: sym0: Reserved 0x2000 bytes for rid 0x1c type 3 at 0xfebd8000 May 5 02:10:15 hitme kernel: sym0: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking May 5 02:10:15 hitme kernel: sym0: open drain IRQ line driver, using on-chip SRAM May 5 02:10:15 hitme kernel: sym0: using LOAD/STORE-based firmware. May 5 02:10:15 hitme kernel: sym0: handling phase mismatch from SCRIPTS. May 5 02:10:15 hitme kernel: sym0: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 00/4e/a0/01/00/04 May 5 02:10:15 hitme kernel: sym0: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 00/4e/80/01/08/04 May 5 02:10:15 hitme kernel: ioapic1: routing intpin 13 (PCI IRQ 29) to vector 52 May 5 02:10:15 hitme kernel: sym0: [GIANT-LOCKED] May 5 02:10:15 hitme kernel: sym0: enabling clock multiplier May 5 02:10:15 hitme kernel: sym0: Downloading SCSI SCRIPTS. May 5 02:10:15 hitme kernel: sym1: <1010-66> port 0xe800-0xe8ff mem 0xfebf8000-0xfebf83ff,0xfebf0000-0xfebf1fff irq 28 at device 6.1 on pci1 May 5 02:10:15 hitme kernel: sym1: Reserved 0x400 bytes for rid 0x14 type 3 at 0xfebf8000 May 5 02:10:15 hitme kernel: sym1: Reserved 0x2000 bytes for rid 0x1c type 3 at 0xfebf0000 May 5 02:10:15 hitme kernel: sym1: Symbios NVRAM, ID 7, Fast-80, SE, parity checking May 5 02:10:15 hitme kernel: sym1: open drain IRQ line driver, using on-chip SRAM May 5 02:10:15 hitme kernel: sym1: using LOAD/STORE-based firmware. May 5 02:10:15 hitme kernel: sym1: handling phase mismatch from SCRIPTS. May 5 02:10:15 hitme kernel: sym1: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 00/4e/a0/01/00/04 May 5 02:10:15 hitme kernel: sym1: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 00/4e/80/01/08/04 the drives are identical 17.5Gb U160 drives (unused) May 5 02:10:15 hitme kernel: pass0: <IBM DPSS-318350M S80D> Fixed Direct Access SCSI-3 device May 5 02:10:15 hitme kernel: pass0: Serial Number ZE0E4501 May 5 02:10:15 hitme kernel: pass0: 160.000MB/s transfers (80.000MHz, offset 62, 16bit), Tagged Queueing Enabled May 5 02:10:15 hitme kernel: pass1 at sym0 bus 0 target 1 lun 0 May 5 02:10:15 hitme kernel: pass1: <IBM DPSS-318350M S80D> Fixed Direct Access SCSI-3 device May 5 02:10:15 hitme kernel: pass1: Serial Number ZE0G1630 May 5 02:10:15 hitme kernel: pass1: 160.000MB/s transfers (80.000MHz, offset 62, 16bit), Tagged Queueing Enabled May 5 02:10:15 hitme kernel: pass2 at sym0 bus 0 target 2 lun 0 May 5 02:10:15 hitme kernel: pass2: <IBM DPSS-318350M S80D> Fixed Direct Access SCSI-3 device May 5 02:10:15 hitme kernel: pass2: Serial Number ZE0B4449 May 5 02:10:15 hitme kernel: pass2: 160.000MB/s transfers (80.000MHz, offset 62, 16bit), Tagged Queueing Enabled May 5 02:10:15 hitme kernel: pass3 at sym1 bus 0 target 3 lun 0 The current system (6.2) is on a single drive on the other SCSI port (IBM - identical to the others). However, when I attempt to stripe the 3 unused drives, I recieve an error regarding da2: gstripe label -v st0 /dev/da0 /dev/da1 /dev/da2 GEOM_STRIPE: Device st0 created (id=2607126992). GEOM_STRIPE: Disk da0 attached to st0. Metadata value stored on /dev/da0. GEOM_STRIPE: Disk da1 attached to st0. Metadata value stored on /dev/da1. GEOM_STRIPE: Disk da2 attached to st0. GEOM_STRIPE: Device st0 activated. GEOM_STRIPE: Cannot add disk da2c to st0 (error=17). Metadata value stored on /dev/da2. I blanked the 3 drives prior to attempting any of this, and it's on a fresh reboot. I'm afraid I don't know how to proceed. Is it a problem with gstripe(8)? I /really/ need to stripe these drives so as to upgrade the system. Thank you for all your time and consideration in this matter. Sincerely, Chris H
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20090505024800.tk0saqntsgk8kk8c>