Date: Tue, 10 May 2011 14:52:20 +0200 From: John Hay <jhay@meraka.org.za> To: freebsd-stable@freebsd.org Subject: MCA: CPU 0 UNCOR PCC DTLB L1 error Message-ID: <20110510125220.GA88338@zibbi.meraka.csir.co.za>
next in thread | raw e-mail | index | archive | help
Hi, I have seen this panic a few times on a Gigabyte E350N-USB3 running 8-STABLE. I have only seen it while in X, but then the machine is always in X. At first, I just got these hangs, so bought a PCI-express RS232 card and could see these at last. For some reason it does not go past this, so I have not been able to get a dump yet. Have anybody an idea of why this is or how to debug it further? I searched the archives and found something similar about a year ago, but it looks like it was solved with a fix that got committed. http://www.freebsd.org/cgi/query-pr.cgi?pr=140338 I have now disabled mca in loader.conf with 'hw.mca.enabled="0"' and I have not seen that panic again. I do occasionally see a panic in devfs_open(), but I guess that should be handled in another thread. The kernel is basically a GENERIC kernel with puc uncommented and the following in loader.conf vm.kmem_size="12G" hw.mca.enabled="0" zfs_load="YES" ahci_load="YES" xhci_load="YES" amdtemp_load="YES" ng_ubt_load="YES" uplcom_load="YES" Here is the panic message and after that dmesg. John -- John Hay -- jhay@meraka.csir.co.za / jhay@FreeBSD.org #################################################### MCA: Bank 0, Status 0xb600000000010015 MCA: Global Cap 0x0000000000000106, Status 0x0000000000000004 MCA: Vendor "AuthenticAMD", ID 0x500f10, APIC ID 0 MCA: CPU 0 UNCOR PCC DTLB L1 error MCA: Address 0x8016c4000 Fatal trap 28: machine check trap while in user mode cpuid = 0; apic id = 00 instruction pointer = 0x43:0x80156af85 stack pointer = 0x3b:0x7fffffffcb18 frame pointer = 0x3b:0x80fe87800 code segment = base 0x0, limit 0xfffff, type 0x1b = DPL 3, pres 1, long 1, def32 0, gran 1 processor eflags = interrupt enabled, IOPL = 0 current process = 2484 (initial thread) trap number = 28 panic: machine check trap cpuid = 0 KDB: stack backtrace: #0 0xffffffff80608d5e at kdb_backtrace+0x5e #1 0xffffffff805d6707 at panic+0x187 #2 0xffffffff808bf4c0 at trap_fatal+0x290 #3 0xffffffff808bfaa9 at trap+0x109 #4 0xffffffff808a7d94 at calltrap+0x8 #################################################### Copyright (c) 1992-2011 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 8.2-STABLE #1: Fri Apr 29 10:14:26 SAST 2011 jhay@angel.cids.org.za:/usr/obj/usr/src/sys/ANGEL amd64 Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: AMD E-350 Processor (1600.07-MHz K8-class CPU) Origin = "AuthenticAMD" Id = 0x500f10 Family = 14 Model = 1 Stepping = 0 Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> Features2=0x802209<SSE3,MON,SSSE3,CX16,POPCNT> AMD Features=0x2e500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM> AMD Features2=0x35ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,IBS,SKINIT,WDT> TSC: P-state invariant real memory = 8589934592 (8192 MB) avail memory = 7841800192 (7478 MB) ACPI APIC Table: <GBT GBTUACPI> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs FreeBSD/SMP: 1 package(s) x 2 core(s) cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 ioapic0: Changing APIC ID to 2 ioapic0 <Version 2.1> irqs 0-23 on motherboard kbd1 at kbdmux0 acpi0: <GBT GBTUACPI> on motherboard acpi0: [ITHREAD] acpi0: Power Button (fixed) acpi0: reservation of 0, a0000 (3) failed acpi0: reservation of 100000, cfcf0000 (3) failed Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 cpu0: <ACPI CPU> on acpi0 cpu1: <ACPI CPU> on acpi0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 vgapci0: <VGA-compatible display> port 0xf800-0xf8ff mem 0xd0000000-0xdfffffff,0xfdfc0000-0xfdffffff irq 18 at device 1.0 on pci0 pci0: <multimedia, HDA> at device 1.1 (no driver attached) pcib1: <ACPI PCI-PCI bridge> irq 16 at device 4.0 on pci0 pci1: <ACPI PCI bus> on pcib1 pcib2: <PCI-PCI bridge> irq 16 at device 0.0 on pci1 pci2: <PCI bus> on pcib2 puc0: <Sunix SER5437A> port 0xef00-0xef1f,0xee00-0xee0f irq 16 at device 8.0 on pci2 puc0: [FILTER] uart0: <16950 or compatible> on puc0 uart0: [FILTER] uart1: <16950 or compatible> on puc0 uart1: [FILTER] ahci0: <ATI IXP700 AHCI SATA controller> port 0xff00-0xff07,0xfe00-0xfe03,0xfd00-0xfd07,0xfc00-0xfc03,0xfb00-0xfb0f mem 0xfe02f000-0xfe02f3ff irq 19 at device 17.0 on pci0 ahci0: [ITHREAD] ahci0: AHCI v1.20 with 4 6Gbps ports, Port Multiplier supported ahcich0: <AHCI channel> at channel 0 on ahci0 ahcich0: [ITHREAD] ahcich1: <AHCI channel> at channel 1 on ahci0 ahcich1: [ITHREAD] ahcich2: <AHCI channel> at channel 2 on ahci0 ahcich2: [ITHREAD] ahcich3: <AHCI channel> at channel 3 on ahci0 ahcich3: [ITHREAD] ohci0: <OHCI (generic) USB controller> mem 0xfe02e000-0xfe02efff irq 18 at device 18.0 on pci0 ohci0: [ITHREAD] usbus0: <OHCI (generic) USB controller> on ohci0 ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfe02d000-0xfe02d0ff irq 17 at device 18.2 on pci0 ehci0: [ITHREAD] usbus1: EHCI version 1.0 usbus1: <EHCI (generic) USB 2.0 controller> on ehci0 ohci1: <OHCI (generic) USB controller> mem 0xfe02c000-0xfe02cfff irq 18 at device 19.0 on pci0 ohci1: [ITHREAD] usbus2: <OHCI (generic) USB controller> on ohci1 ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfe02b000-0xfe02b0ff irq 17 at device 19.2 on pci0 ehci1: [ITHREAD] usbus3: EHCI version 1.0 usbus3: <EHCI (generic) USB 2.0 controller> on ehci1 pci0: <serial bus, SMBus> at device 20.0 (no driver attached) atapci0: <ATI IXP700/800 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfa00-0xfa0f at device 20.1 on pci0 ata0: <ATA channel 0> on atapci0 ata0: [ITHREAD] ata1: <ATA channel 1> on atapci0 ata1: [ITHREAD] pci0: <multimedia, HDA> at device 20.2 (no driver attached) isab0: <PCI-ISA bridge> at device 20.3 on pci0 isa0: <ISA bus> on isab0 pcib3: <ACPI PCI-PCI bridge> at device 20.4 on pci0 ACPI Warning: For \\_SB_.PCI0.P2P_._PRT: Return Package has no elements (empty) (20101013/nspredef-572) pci3: <ACPI PCI bus> on pcib3 ohci2: <OHCI (generic) USB controller> mem 0xfe02a000-0xfe02afff irq 18 at device 20.5 on pci0 ohci2: [ITHREAD] usbus4: <OHCI (generic) USB controller> on ohci2 pcib4: <ACPI PCI-PCI bridge> at device 21.0 on pci0 pci4: <ACPI PCI bus> on pcib4 re0: <RealTek 8168/8111 B/C/CP/D/DP/E PCIe Gigabit Ethernet> port 0xce00-0xceff mem 0xfdbff000-0xfdbfffff,0xfdbf8000-0xfdbfbfff irq 17 at device 0.0 on pci4 re0: Using 1 MSI-X message re0: Chip rev. 0x2c000000 re0: MAC rev. 0x00000000 miibus0: <MII bus> on re0 rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus0 rgephy0: 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow re0: Ethernet address: 1c:6f:65:c2:00:a7 re0: [ITHREAD] pcib5: <ACPI PCI-PCI bridge> at device 21.1 on pci0 pci5: <ACPI PCI bus> on pcib5 xhci0: <XHCI (generic) USB 3.0 controller> mem 0xfdafe000-0xfdafffff irq 17 at device 0.0 on pci5 xhci0: [ITHREAD] xhci0: 32 byte context size. usbus5 on xhci0 ohci3: <OHCI (generic) USB controller> mem 0xfe029000-0xfe029fff irq 18 at device 22.0 on pci0 ohci3: [ITHREAD] usbus6: <OHCI (generic) USB controller> on ohci3 ehci2: <EHCI (generic) USB 2.0 controller> mem 0xfe028000-0xfe0280ff irq 17 at device 22.2 on pci0 ehci2: [ITHREAD] usbus7: EHCI version 1.0 usbus7: <EHCI (generic) USB 2.0 controller> on ehci2 amdtemp0: <AMD CPU On-Die Thermal Sensors> on hostb4 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] atkbd0: [ITHREAD] atrtc0: <AT realtime clock> port 0x70-0x73 irq 8 on acpi0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 ppc0: cannot reserve I/O port range hwpstate0: <Cool`n'Quiet 2.0> on cpu0 ZFS filesystem version 4 ZFS storage pool version 15 Timecounters tick every 1.000 msec usbus0: 12Mbps Full Speed USB v1.0 usbus1: 480Mbps High Speed USB v2.0 usbus2: 12Mbps Full Speed USB v1.0 usbus3: 480Mbps High Speed USB v2.0 usbus4: 12Mbps Full Speed USB v1.0 usbus5: 5.0Gbps Super Speed USB v3.0 usbus6: 12Mbps Full Speed USB v1.0 usbus7: 480Mbps High Speed USB v2.0 ugen0.1: <ATI> at usbus0 uhub0: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 ugen1.1: <ATI> at usbus1 uhub1: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 ugen2.1: <ATI> at usbus2 uhub2: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2 ugen3.1: <ATI> at usbus3 uhub3: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3 ugen4.1: <ATI> at usbus4 uhub4: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4 ugen5.1: <0x1033> at usbus5 uhub5: <0x1033 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus5 ugen6.1: <ATI> at usbus6 uhub6: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6 ugen7.1: <ATI> at usbus7 uhub7: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus7 ada0 at ahcich0 bus 0 scbus0 target 0 lun 0 ada0: <ST2000DL003-9VT166 CC32> ATA-8 SATA 3.x device ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes) ada0: Command Queueing enabled ada0: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C) ada1 at ahcich1 bus 0 scbus1 target 0 lun 0 ada1: <ST2000DL003-9VT166 CC32> ATA-8 SATA 3.x device ada1: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes) ada1: Command Queueing enabled ada1: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C) SMP: AP CPU #1 Launched! uhub4: 2 ports with 2 removable, self powered uhub6: 4 ports with 4 removable, self powered uhub0: 5 ports with 5 removable, self powered uhub2: 5 ports with 5 removable, self powered uhub5: 4 ports with 4 removable, self powered Root mount waiting for: usbus7 usbus3 usbus1 Root mount waiting for: usbus7 usbus3 usbus1 uhub7: 4 ports with 4 removable, self powered uhub1: 5 ports with 5 removable, self powered uhub3: 5 ports with 5 removable, self powered Root mount waiting for: usbus3 usbus1 Trying to mount root from zfs:dam/ROOT/amd64 ugen2.2: <Logitech> at usbus2 ugen0.2: <Prolific Technology Inc.> at usbus0 uplcom0: <Prolific Technology Inc. USB-Serial Controller, class 0/0, rev 1.10/3.00, addr 2> on usbus0 ukbd0: <Logitech USB Receiver, class 0/0, rev 2.00/15.00, addr 2> on usbus2 kbd2 at ukbd0 ums0: <Logitech USB Receiver, class 0/0, rev 2.00/15.00, addr 2> on usbus2 ums0: 18 buttons and [XYZT] coordinates ID=2 ugen2.3: <Conwise Technology> at usbus2 ubt0: <Conwise Technology USB demo board, class 224/1, rev 1.10/1.34, addr 3> on usbus2 ugen0.3: <American Power Conversion> at usbus0 WARNING: attempt to domain_add(bluetooth) after domainfinalize() WARNING: attempt to domain_add(netgraph) after domainfinalize() ubt0: ubt_ctrl_write_callback:667: control transfer failed: USB_ERR_TIMEOUT ng_hci_process_command_timeout: ubt0hci - unable to complete HCI command OGF=0x3, OCF=0x3. Timeout
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20110510125220.GA88338>