Date: Sat, 10 Mar 2012 20:33:16 +0100 From: "Julian H. Stacey" <jhs@berklix.com> To: Hans Petter Selasky <hselasky@c2i.net> Cc: freebsd-usb@freebsd.org Subject: Re: ICY BOX Sata USB box runs ar 1M instead of 40M+ Message-ID: <201203101933.q2AJXGfd025146@fire.js.berklix.net> In-Reply-To: Your message "Sat, 10 Mar 2012 17:20:28 %2B0100." <201203101720.28148.hselasky@c2i.net>
next in thread | previous in thread | raw e-mail | index | archive | help
Hans Petter Selasky wrote: > On Saturday 10 March 2012 15:16:05 Julian H. Stacey wrote: > > Hi USB folks, > > For external disk enclosure, trade name "ICY BOX" > > /var/log messages shows USB configuring for 1.000MB/s > > > > The cardboard box I bought it in from shop says > > 1 x 2.5" SATA, 1 x USB 3.0 IB-231StU3 > > http://www.icybox.de -> > > http://www.raidsonic.de/en/products/details.php?we_objectID=7564 > > Clicking Spec says: USB 3.0 up to 5 Gbit/s > > > > The HP notebook > > http://berklix.com/~jhs/hardware/hp/pavilion/dm3-1155ea > > has 4 USB 2.0 ports. > > > > If I connect a USB stick on the same port, the notebook offers 40M. > > > > The disk on all 4 ports only offers 1M. > > I tried external power to disk too, no help > > (well I'd hoped maybe low V might have sabotaged negotiation - long shot > > ;-) > > > > I suspect/ hope I just need to do a quirk table entry ? Hints please ? > > > > 8.2-RELEASE amd64, > > I'd prefer to stay on 8.2 but I have a smallish space for a temporary > > current or 9 if I have to. > > Hi, > > Are there any errors in dmesg? Not that I can see, (I've got a cold so I might have missed something but dont think so) After a fresh reboot & plugging in disk I see: ugen0.2: <01234567890123456789012345678901234567890123> at usbus0 umass0: <01234567890123456789012345678901234567890123 012345678901234567890123456789012345678901234567, class 0/0, rev 2.10/1.00, addr 2> on usbus0 umass0: SCSI over Bulk-Only; quirks = 0x0000 umass0:0:0:-1: Attached to scbus0 da0 at umass-sim0 bus 0 scbus0 target 0 lun 0 da0: <WDC WD25 00BEKT-60A25T1 02.0> Fixed Direct Access SCSI-5 device da0: 1.000MB/s transfers da0: 238475MB (488397168 512 byte sectors: 255H 63S/T 30401C) GEOM: da0: partition 4 does not start on a track boundary. GEOM: da0: partition 4 does not end on a track boundary. GEOM: da0: partition 3 does not start on a track boundary. GEOM: da0: partition 3 does not end on a track boundary. GEOM: da0: partition 2 does not start on a track boundary. GEOM: da0: partition 2 does not end on a track boundary. GEOM: da0: partition 1 does not start on a track boundary. GEOM: da0: partition 1 does not end on a track boundary. > 1.0 MByte/s is because it enumerates at FULL speed instead of HIGH speed. Umm. Yes the puzzle is why it doesnt do USB-2 = High. > Check with usbconfig ugen0.1: <OHCI root HUB ATI> at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE ugen1.1: <OHCI root HUB ATI> at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE ugen2.1: <EHCI root HUB ATI> at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE ugen3.1: <OHCI root HUB ATI> at usbus3, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE ugen4.1: <EHCI root HUB ATI> at usbus4, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE ugen0.2: <012345678901234567890123456789012345678901234567 012345678901234567890123456789012345, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON ugen2.2: <CNF9012 Chicony Electronics Co., Ltd.> at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON usbconfig -d ugen0.2 dump_device_desc ugen0.2: <012345678901234567890123456789012345678901234567 012345678901234567890123456789012345, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON bLength = 0x0012 bDescriptorType = 0x0001 bcdUSB = 0x0210 bDeviceClass = 0x0000 bDeviceSubClass = 0x0000 bDeviceProtocol = 0x0000 bMaxPacketSize0 = 0x0040 idVendor = 0x174c idProduct = 0x55aa bcdDevice = 0x0100 iManufacturer = 0x0002 <01234567890123456789012345678901234567890123> iProduct = 0x0003 <012345678901234567890123456789012345678901234567> iSerialNumber = 0x0001 <0123456789ABCDEF0188> bNumConfigurations = 0x0001 usbconfig -d ugen0.2 dump_curr_config_desc ugen0.2: <012345678901234567890123456789012345678901234567 012345678901234567890123456789012345, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON Configuration index 0 bLength = 0x0009 bDescriptorType = 0x0002 wTotalLength = 0x0020 bNumInterfaces = 0x0001 bConfigurationValue = 0x0001 iConfiguration = 0x0000 <no string> bmAttributes = 0x00c0 bMaxPower = 0x0000 Interface 0 bLength = 0x0009 bDescriptorType = 0x0004 bInterfaceNumber = 0x0000 bAlternateSetting = 0x0000 bNumEndpoints = 0x0002 bInterfaceClass = 0x0008 bInterfaceSubClass = 0x0006 bInterfaceProtocol = 0x0050 iInterface = 0x0000 <no string> Endpoint 0 bLength = 0x0007 bDescriptorType = 0x0005 bEndpointAddress = 0x0081 <IN> bmAttributes = 0x0002 <BULK> wMaxPacketSize = 0x0040 bInterval = 0x0000 bRefresh = 0x0000 bSynchAddress = 0x0000 Endpoint 1 bLength = 0x0007 bDescriptorType = 0x0005 bEndpointAddress = 0x0002 <OUT> bmAttributes = 0x0002 <BULK> wMaxPacketSize = 0x0040 bInterval = 0x0000 bRefresh = 0x0000 bSynchAddress = 0x0000 usbconfig -d ugen0.2 dump_info ugen0.2: <012345678901234567890123456789012345678901234567 012345678901234567890123456789012345, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON usbconfig -d ugen0.2 show_ifdrv ugen0.2: <012345678901234567890123456789012345678901234567 012345678901234567890123456789012345, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON ugen0.2.0: umass0: <01234567890123456789012345678901234567890123 012345678901234567890123456789012345678901234567, class 0/0, rev 2.10/1.0 usbconfig -d ugen0.2 list ugen0.2: <012345678901234567890123456789012345678901234567 012345678901234567890123456789012345, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON usbconfig dump_quirk_names | more shows nothing I might think of as "Force this to USB-2 high speed. I did a find & grep for Bulk-Only in /usr/src & found /sys/dev/usb/storage/ustorage_fs.c # no keyword quirk /sys/dev/usb/storage/umass.c contains USB_SPEED_HIGH ... & before switch (usbd_get_speed(sc->sc_udev) dev/usb/usb_device.c enum usb_dev_speed usbd_get_speed(struct usb_device *udev) { return (udev->speed); } But then I'm lost ? Cheers, Julian -- Julian Stacey, BSD Unix Linux C Sys Eng Consultants Munich http://berklix.com Reply below not above, cumulative like a play script, & indent with "> ". Format: Plain text. Not HTML, multipart/alternative, base64, quoted-printable. Mail from @yahoo dumped @berklix. http://berklix.org/yahoo/
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?201203101933.q2AJXGfd025146>