Date: Sat, 17 Oct 1998 12:08:49 +0100 From: Karl Pielorz <kpielorz@tdx.co.uk> To: current@FreeBSD.ORG Subject: SCSI / CAM error or warning output? Message-ID: <36287AC1.3F0C0D9C@tdx.co.uk>
next in thread | raw e-mail | index | archive | help
Hi All (again?) This might be considered slightly more -hardware oriented, but I thought -current was probably more appropriate as current probably has the later version of CAM... My system's started spitting these out on the console, whilst I can get the 'jist' of what it's trying to say, can someone translate for me? (and tell me whether it's good or bad?) - system is -current as of 10/16 @ 16:43... ahc2 is a 2940UW, with 3 x Quantum drives on it. First 2 are un-terminated, third is using onboard active termination, controller is set to terminate high & low bits. Cable is a nice Adaptec cable (so _please_ don't tell me it's termination <G>)... This happens when the drives are 'busy' (but not totally thrashed)... " ahc2:A:8: no active SCB for reconnecting target - issuing BUS DEVICE RESET SAVED_TCL == 0x80, ARG_1 == 0x1b, SEQ_FLAGS == 0x40 ahc2: Bus Device Reset on A:8. 6 SCBs aborted (da4:ahc2:0:8:0): tagged openings now 64 (da4:ahc2:0:8:0): tagged openings now 63 Timedout SCB handled by another timeout (da5:ahc2:0:9:0): data overrun detected in Data-In phase. Tag == 0x2. (da5:ahc2:0:9:0): Have seen Data Phase. Length = 8192. NumSGs = 1. Timedout SCB handled by another timeout ahc2: WARNING no command for scb 65 (cmdcmplt) QOUTPOS = 1 ahc2: WARNING no command for scb 65 (cmdcmplt) QOUTPOS = 34 ahc2: WARNING no command for scb 65 (cmdcmplt) QOUTPOS = 43 ahc2: WARNING no command for scb 1 (cmdcmplt) QOUTPOS = 58 ahc2:A:10: ahc_intr - referenced scb not valid during seqint 0x71 scb(1) ahc2: WARNING no command for scb 1 (cmdcmplt) QOUTPOS = 67 " DMesg for ah2 is: " ahc2: <Adaptec 2940 Ultra SCSI adapter> rev 0x00 int a irq 19 on pci0.20.0 ahc2: aic7880 Wide Channel A, SCSI Id=7, 16/255 SCBs " Drives are: " da4 at ahc2 bus 0 target 8 lun 0 da4: <SEAGATE ST34371W 0202> Fixed Direct Access SCSI2 device da4: 20.0MB/s transfers (10.0MHz, offset 8, 16bit), Tagged Queueing Enabled da4: 4148MB (8496960 512 byte sectors: 255H 63S/T 528C) da5 at ahc2 bus 0 target 9 lun 0 da5: <SEAGATE ST34371W 0202> Fixed Direct Access SCSI2 device da5: 20.0MB/s transfers (10.0MHz, offset 8, 16bit), Tagged Queueing Enabled da5: 4148MB (8496960 512 byte sectors: 255H 63S/T 528C) da6 at ahc2 bus 0 target 10 lun 0 da6: <SEAGATE ST34371W 0202> Fixed Direct Access SCSI2 device da6: 20.0MB/s transfers (10.0MHz, offset 8, 16bit), Tagged Queueing Enabled da6: 4148MB (8496960 512 byte sectors: 255H 63S/T 528C) " Regards, Karl To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?36287AC1.3F0C0D9C>