Date: Sun, 07 Nov 1999 16:01:55 +0100 From: "D. Rock" <rock@dead-end.net> To: hm@hcs.de Cc: Charlie ROOT <root@neland.dk>, freebsd-current@FreeBSD.ORG Subject: Re: Dr Neuhaus niccy go not recognized Message-ID: <38259463.FDEA7F45@dead-end.net> References: <19991107130146.2B72E38E2@hcswork.hcs.de>
next in thread | previous in thread | raw e-mail | index | archive | help
Hellmuth Michaelis wrote:
>
> >From the keyboard of Charlie ROOT:
>
> > During make of kernel:
> >
> > cc -c -O -Wall -Wredundant-decls -Wnested-externs -Wstrict-prototypes
> > -Wmissing-prototypes -Wpointer-arith -Winline -Wcast-qual
> > -fformat-extensions -ansi -nostdinc -I- -I. -I../.. -I../../../include
> > -DKERNEL -include opt_global.h -elf ../../i4b/layer1/i4b_isic_pnp.c
> > ../../i4b/layer1/i4b_isic_pnp.c:53: warning: #warning "Fix i4b pnp!"
> >
> > Is this a "simple" matter of the right options to config, or does it
> > involve changes to the code?
>
> PnP support for i4b in -current was disabled during the conversion of
> -current to the new-bus/new-pnp architecture; as a result all PnP ISDN
> cards i4b supports do no longer work.
Any hints when i4b will be converted to new-bus? The code is in stale
condition for almost 3 months now.
To the original poster:
I also have an ISDN PnP card (SedlBauer WinSpeed). In order to get it
run on -current, I did the following:
- disable "controller pnp0" in your kernel config file (If you need it
for some other device, bad luck)
- note which resources your PnP card were assigned.
- use good old style in your config [my config]
device isic0 at isa? port 0x108 irq 10 flags 9
(take a look at /sys/i4b/layer1/i4b_l1.h for your flag number).
- patch some files in the i4b tree (hope it is as simple for
your device). The example below is from my configuration:
Index: i4b_isic_isa.c
===================================================================
RCS file: /data/cvs/src/sys/i4b/layer1/i4b_isic_isa.c,v
retrieving revision 1.6
diff -u -r1.6 i4b_isic_isa.c
--- i4b_isic_isa.c 1999/08/28 00:45:40 1.6
+++ i4b_isic_isa.c 1999/09/26 18:15:40
@@ -204,6 +204,12 @@
break;
#endif
+#ifdef SEDLBAUER
+ case FLAG_SWS:
+ ret = isic_probe_sws(dev);
+ break;
+#endif
+
default:
break;
}
Index: i4b_sws.c
===================================================================
RCS file: /data/cvs/src/sys/i4b/layer1/i4b_sws.c,v
retrieving revision 1.5
diff -u -r1.5 i4b_sws.c
--- i4b_sws.c 1999/08/28 00:45:41 1.5
+++ i4b_sws.c 1999/09/26 19:44:50
@@ -283,6 +283,11 @@
/* attach callback routine */
+int isic_probe_sws(struct isa_device *dev)
+{
+ return(1);
+}
+
int
isic_attach_sws(struct isa_device *dev)
{
Index: isa_isic.c
===================================================================
RCS file: /data/cvs/src/sys/i4b/layer1/isa_isic.c,v
retrieving revision 1.5
diff -u -r1.5 isa_isic.c
--- isa_isic.c 1999/08/28 00:45:43 1.5
+++ isa_isic.c 1999/09/26 18:11:33
@@ -196,6 +196,12 @@
break;
#endif
+#ifdef SEDLBAUER
+ case FLAG_SWS:
+ ret = isic_probe_sws(&args);
+ break;
+#endif
+
default:
/* No card type given, try to figure ... */
if (ia->ia_iobase == IOBASEUNK) {
[all files are relative to /sys/i4b/layer1]
One note: The device doesn't get reset properly during reboot. I don't know
if this a general problem with the driver or just a result from my hacks.
If I reboot I have to manually turn off/on the machine.
Besides from this error, I hadn't had any problems so far.
Daniel
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?38259463.FDEA7F45>