Date: Thu, 22 Mar 2001 20:35:21 +0100 From: Falco Krepel <krepel@fokus.gmd.de> To: "Justin T. Gibbs" <gibbs@scsiguy.com>, freebsd-current@FreeBSD.ORG Subject: Re: ahc driver: aic7892 no longer supported (conflict with ATA) Message-ID: <3ABA53F9.DB191FA3@fokus.gmd.de> References: <200103202342.f2KNfvs74802@aslan.scsiguy.com>
next in thread | previous in thread | raw e-mail | index | archive | help
I think I found the problem. The problem occur since 03/14/2001. The following files could be infvolved: P dev/ata/ata-all.c P dev/ata/ata-all.h P dev/ata/ata-disk.c P dev/ata/ata-disk.h P dev/ata/atapi-all.c P dev/ata/atapi-all.h P dev/ata/atapi-cd.c P dev/ata/atapi-cd.h P dev/ata/atapi-fd.c P dev/ata/atapi-fd.h P dev/ata/atapi-tape.c P dev/ata/atapi-tape.h It should be somthing in ata-all.c. Because since 03/14 the ata1 probe doesn't fail and uses irq 15 same as the ahc. But this shouldn't be a problem. I am right? => boot failed (since 03/14/2001) atapci0: <VIA 82C686 ATA100 controller> port 0xd000-0xd00f at device 7.1 on pci0 ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xd000 ata0: mask=03 status0=50 status1=00 ata0-master: ATAPI probe 14 eb ata0-slave: ATAPI probe 14 eb ata0: mask=03 status0=10 status1=00 ata0: devices=0c ata0: at 0x1f0 irq 14 on atapci0 ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xd008 ata1: at 0x170 irq 15 on atapci0 pci0: <bridge, PCI-unknown> at 7.4 (no driver attached) ahc0: <Adaptec 29160 Ultra160 SCSI adapter> port 0xdc00-0xdcff mem 0xdf000000-0xdf000fff irq 15 at device 9.0 on pci0 ahc0: Platform free device_probe_and_attach: ahc0 attach returned 12 => boot working (03/13/2001 and before) atapci0: <VIA 82C686 ATA100 controller> port 0xd000-0xd00f at device 7.1 on pci0 ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xd000 ata0: mask=03 status0=50 status1=00 ata0: mask=03 ostat0=50 ostat2=00 ata0-master: ATAPI probe a=14 b=eb ata0-slave: ATAPI probe a=14 b=eb ata0: mask=03 status0=10 status1=00 ata0: devices=0c ata0: at 0x1f0 irq 14 on atapci0 ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xd008 ata1: mask=00 status0=ff status1=ff ata1: probe allocation failed pci0: <bridge, PCI-unknown> at 7.4 (no driver attached) ahc0: <Adaptec 29160 Ultra160 SCSI adapter> port 0xdc00-0xdcff mem 0xdf000000-0xdf000fff irq 15 at device 9.0 on pci0 ahc0: Reading SEEPROM...done. ahc0: BIOS eeprom is present ahc0: Secondary High byte termination Enabled ahc0: Secondary Low byte termination Enabled ahc0: Primary Low Byte termination Enabled ahc0: Primary High Byte termination Enabled ahc0: Downloading Sequencer Program... 424 instructions downloaded aic7892: Wide Channel A, SCSI Id=7, 32/255 SCBs -- Falco Krepel Phone: +49-(0)30 - 34 63 - 7 276 GMD-FOKUS Fax: +49-(0)30 - 34 63 - 8 276 Kaiserin-Augusta-Allee 31 e-mail: krepel@fokus.gmd.de 10589 Berlin WWW: http://www.fokus.gmd.de/usr/krepel To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3ABA53F9.DB191FA3>