Date: Fri, 18 May 2001 09:52:19 -0500 From: "Jeffrey J. Mountin" <jeff-ml@mountin.net> To: Doug Hardie <bc979@lafn.org> Cc: freebsd-stable@FreeBSD.ORG Subject: Re: Hardware Problem Message-ID: <4.3.2.20010518093939.02d8aad0@207.227.119.2> In-Reply-To: <f04330145b72a0b01dd50@[10.0.1.100]> References: <4.3.2.20010517174928.02d75b00@207.227.119.2> <20010516014155.A19796@the-7.net> <20010516014155.A19796@the-7.net> <4.3.2.20010517174928.02d75b00@207.227.119.2>
next in thread | previous in thread | raw e-mail | index | archive | help
At 04:12 PM 5/17/01 -0700, Doug Hardie wrote: >I have several systems with basically the same hardware. The problem only >occurs on one of them. Here is the boot: By verbose I meant a 'boot -v'. Custom or GENERIC kernel here? >Copyright (c) 1992-2001 The FreeBSD Project. >Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. >FreeBSD 4.3-RELEASE #1: Fri May 11 16:39:12 PDT 2001 > doug@zool.lafn.org:/usr/obj/usr/src/sys/ZOOK >Timecounter "i8254" frequency 1193182 Hz >CPU: Pentium III/Pentium III Xeon/Celeron (551.25-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0x673 Stepping = 3 >Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> >real memory = 134201344 (131056K bytes) >avail memory = 126324736 (123364K bytes) >Preloaded elf kernel "kernel" at 0xc043f000. >Pentium Pro MTRR support enabled >md0: Malloc disk >npx0: <math processor> on motherboard >npx0: INT 16 interface >pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard >pci0: <PCI bus> on pcib0 >pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0 >pci1: <PCI bus> on pcib1 >isab0: <Intel 82371AB PCI to ISA bridge> at device 4.0 on pci0 >isa0: <ISA bus> on isab0 >atapci0: <Intel PIIX4 ATA33 controller> port 0xd800-0xd80f at device 4.1 >on pci0 > >2 minute delay here Hmmm... >uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xd400-0xd41f irq 9 >at device 4.2 on pci0 >usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0 >usb0: USB revision 1.0 >uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 >uhub0: 2 ports with 2 removable, self powered >chip1: <Intel 82371AB Power management controller> port 0xe800-0xe80f at >device 4.3 on pci0 >dc0: <82c169 PNIC 10/100BaseTX> port 0xd000-0xd0ff mem >0xe3000000-0xe30000ff irq 5 at device 10.0 on pci0 >dc0: Ethernet address: 00:a0:cc:3e:87:dc >miibus0: <MII bus> on dc0 >ukphy0: <Generic IEEE 802.3u media interface> on miibus0 >ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto >pci0: <Trident model 9660 VGA-compatible display device> at 11.0 irq 12 >ahc0: <Adaptec 2940 Ultra SCSI adapter> port 0xb800-0xb8ff mem >0xe1800000-0xe1800fff irq 11 at device 12.0 on pci0 >aic7880: Wide Channel A, SCSI Id=7, 16/255 SCBs >fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 >fdc0: FIFO enabled, 8 bytes threshold >fd0: <1440-KB 3.5" drive> on fdc0 drive 0 >atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 >atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 >kbd0 at atkbd0 >vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 >sc0: <System console> at flags 0x100 on isa0 >sc0: VGA <16 virtual consoles, flags=0x300> >sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 >sio0: type 16550A >sio1 at port 0x2f8-0x2ff irq 3 on isa0 >sio1: type 16550A >ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 >ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode >ppc0: FIFO with 16/16/9 bytes threshold >plip0: <PLIP network interface> on ppbus0 >lpt0: <Printer> on ppbus0 >lpt0: Interrupt-driven port A bit familar, a few others had problems with various hardware with the parallel port. Disabling it did eliminate the pause, but for some that wasn't a long term solution. You say this is a production server. Any IDE devices in use? If no, remove them from the kernel config. >ppi0: <Parallel I/O> on ppbus0 >ep0 at port 0x300 iomem 0xd8000 irq 10 on isa0 >ep0: Ethernet address 00:a0:24:7a:bf:e0 >isa_compat: didn't get irq for lnc >ep1: <3Com 3C509-BNC EtherLink III> at port 0x300-0x30f irq 5 on isa0 >ep1: No irq?! >ep1: ep_alloc() failed! (6) >device_probe_and_attach: ep1 attach returned 6 --snip-- Do you have 3 network cards? As is dc0 and ep1 are trying to use the same IRQ. It would help if you listed the hardware. Jeff Mountin - jeff@mountin.net Systems/Network Administrator FreeBSD - the power to serve To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?4.3.2.20010518093939.02d8aad0>