Date: Mon, 05 Jun 2006 17:32:50 -0400 From: srwadleigh <srw@udor.net> To: freebsd-stable@freebsd.org Subject: 6.1-RELEASE: WARNING - WRITE_DMA soft error Message-ID: <4484A302.8050107@udor.net>
next in thread | raw e-mail | index | archive | help
This is a multi-part message in MIME format. --------------010300000005080707060406 Content-Type: text/plain; charset=ISO-8859-1; format=flowed Content-Transfer-Encoding: 7bit I have 6.1-RELEASE installed on a Supermicro SuperServer 6014P-TR with Supermicro motherboard: Super X6DHP-TG http://supermicro.com/products/motherboard/Xeon800/E7520/X6DHP-TG.cfm I have four SATA drives attached to the internal backplane which uses the following controller, I am Not using the onboard RAID features: Marvell 88SX6081 4-port SATA Controller with 3rd-Party Adaptec AIC-8110(4x drive), RAID 0, 1, JBOD support The problem I am seeing occurs with the fourth drive, ad10, and appears on all read/write operations: ad10: WARNING - WRITE_DMA48 soft error (ECC corrected) LBA=293046767 kernel:ad10: WARNING - WRITE_DMA soft error (ECC corrected) LBA=12393823 kernel:ad10: WARNING - READ_DMA soft error (ECC corrected) LBA=12480567 This same warning message appears on 6.0-RELEASE and 6.1-STABLE I have tried swapping drives around, and tried fewer than four drives to see if I could tie the warning message to either a specific drive or the number of drives attached to the controller but the message only appears for the fourth drive port. Beyond the warning message the drive seems to read and write data correctly. Currently ad8 and ad10 are joined as providers in a gmirror configuration, both drives seem to behave fine, but rebuilding the mirror makes ad10 go crazy with it's ECC warning messages. Gmirror does not degrade status of the array or anything else related to the warnings. Also the warning shows up in dmesg before gmirror providers are initialized, and before I initially setup gmirror on the system. Hardware issue with the port? Or a controller-driver issue perhaps? How dangerous is a soft error? Any help on tracking down the cause, implications, or a solution would be greatly appreciated, as it stands I am a little nervous trusting this system under any kind of load. I have attached a verbose dmesg output. I posted this to the GEOM list but later realized it might be appropriate for -STABLE since I see a few other -RELEASE related posts here, at any rate sorry for the cross posting. Thank You wadleigh --------------010300000005080707060406 Content-Type: text/plain; name="dmesg_boot.txt" Content-Transfer-Encoding: 7bit Content-Disposition: inline; filename="dmesg_boot.txt" MADT: Interrupt override: source 9, irq 9 ioapic0: intpin 9 trigger: level ioapic0: intpin 9 polarity: high lapic0: Routing NMI -> LINT1 lapic0: LINT1 trigger: edge lapic0: LINT1 polarity: high ioapic0 <Version 2.0> irqs 0-23 on motherboard ioapic1 <Version 2.0> irqs 24-47 on motherboard ioapic2 <Version 2.0> irqs 48-71 on motherboard cpu0 BSP: ID: 0x00000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff timer: 0x000100ef therm: 0x00000200 err: 0x00010000 pcm: 0x00010000 io: <I/O> kbd: new array size 4 kbd1 at kbdmux0 nfslock: pseudo-device mem: <memory> Pentium Pro MTRR support enabled null: <null device, zero device> random: <entropy source, Software, Yarrow> npx0: INT 16 interface acpi0: <PTLTD RSDT> on motherboard ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48 acpi0: [MPSAFE] pci_open(1): mode 1 addr port (0x0cf8) is 0x80000058 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=35908086) pcibios: BIOS version 2.10 Found $PIR table, 18 entries at 0xc00fdea0 PCI-Only Interrupts: none Location Bus Device Pin Link IRQs embedded 0 1 A 0x60 3 4 5 6 7 9 10 11 12 embedded 0 2 A 0x60 3 4 5 6 7 9 10 11 12 slot 2 2 1 A 0x60 3 4 5 6 7 9 10 11 12 slot 2 2 1 B 0x61 3 4 5 6 7 9 10 11 12 slot 2 2 1 C 0x60 3 4 5 6 7 9 10 11 12 slot 2 2 1 D 0x61 3 4 5 6 7 9 10 11 12 slot 5 2 2 A 0x60 3 4 5 6 7 9 10 11 12 slot 5 2 2 B 0x61 3 4 5 6 7 9 10 11 12 slot 1 3 1 A 0x60 3 4 5 6 7 9 10 11 12 slot 1 3 1 B 0x61 3 4 5 6 7 9 10 11 12 slot 1 3 1 C 0x62 3 4 5 6 7 9 10 11 12 slot 1 3 1 D 0x63 3 4 5 6 7 9 10 11 12 slot 6 3 2 A 0x62 3 4 5 6 7 9 10 11 12 slot 6 3 2 B 0x63 3 4 5 6 7 9 10 11 12 embedded 0 4 A 0x60 3 4 5 6 7 9 10 11 12 slot 4 4 0 A 0x60 3 4 5 6 7 9 10 11 12 slot 4 4 0 B 0x61 3 4 5 6 7 9 10 11 12 slot 4 4 0 C 0x62 3 4 5 6 7 9 10 11 12 slot 4 4 0 D 0x63 3 4 5 6 7 9 10 11 12 embedded 0 6 A 0x60 3 4 5 6 7 9 10 11 12 slot 3 5 0 A 0x60 3 4 5 6 7 9 10 11 12 slot 3 5 0 B 0x61 3 4 5 6 7 9 10 11 12 slot 3 5 0 C 0x62 3 4 5 6 7 9 10 11 12 slot 3 5 0 D 0x63 3 4 5 6 7 9 10 11 12 embedded 6 1 A 0x61 3 4 5 6 7 9 10 11 12 embedded 6 2 A 0x60 3 4 5 6 7 9 10 11 12 embedded 6 2 B 0x61 3 4 5 6 7 9 10 11 12 embedded 0 31 A 0x62 3 4 5 6 7 9 10 11 12 embedded 0 31 B 0x61 3 4 5 6 7 9 10 11 12 embedded 0 29 A 0x60 3 4 5 6 7 9 10 11 12 embedded 0 29 B 0x63 3 4 5 6 7 9 10 11 12 embedded 0 29 C 0x62 3 4 5 6 7 9 10 11 12 embedded 0 29 D 0x6b 3 4 5 6 7 9 10 11 12 Setting up PCIe mappings for BAR 0xe0000000 AcpiOsDerivePciId: bus 0 dev 31 func 0 AcpiOsDerivePciId: bus 0 dev 31 func 0 AcpiOsDerivePciId: bus 0 dev 31 func 0 acpi0: Power Button (fixed) AcpiOsDerivePciId: bus 0 dev 0 func 0 AcpiOsDerivePciId: bus 0 dev 31 func 0 pci_link0: Links after initial probe: Index IRQ Rtd Ref IRQs 0 5 N 0 3 4 5 6 7 10 11 14 15 pci_link0: Links after initial validation: Index IRQ Rtd Ref IRQs 0 5 N 0 3 4 5 6 7 10 11 14 15 pci_link0: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 10 11 14 15 pci_link1: Links after initial probe: Index IRQ Rtd Ref IRQs 0 10 N 0 3 4 5 6 7 10 11 14 15 pci_link1: Links after initial validation: Index IRQ Rtd Ref IRQs 0 10 N 0 3 4 5 6 7 10 11 14 15 pci_link1: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 10 11 14 15 pci_link2: Links after initial probe: Index IRQ Rtd Ref IRQs 0 7 N 0 3 4 5 6 7 10 11 14 15 pci_link2: Links after initial validation: Index IRQ Rtd Ref IRQs 0 7 N 0 3 4 5 6 7 10 11 14 15 pci_link2: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 10 11 14 15 pci_link3: Links after initial probe: Index IRQ Rtd Ref IRQs 0 11 N 0 3 4 5 6 7 10 11 14 15 pci_link3: Links after initial validation: Index IRQ Rtd Ref IRQs 0 11 N 0 3 4 5 6 7 10 11 14 15 pci_link3: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 10 11 14 15 pci_link4: Links after initial probe: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 10 11 14 15 pci_link4: Links after initial validation: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 10 11 14 15 pci_link4: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 10 11 14 15 pci_link5: Links after initial probe: Index IRQ Rtd Ref IRQs 0 255 N 0 4 5 6 7 10 11 14 15 pci_link5: Links after initial validation: Index IRQ Rtd Ref IRQs 0 255 N 0 4 5 6 7 10 11 14 15 pci_link5: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 4 5 6 7 10 11 14 15 pci_link6: Links after initial probe: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 10 11 14 15 pci_link6: Links after initial validation: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 10 11 14 15 pci_link6: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 10 11 14 15 pci_link7: Links after initial probe: Index IRQ Rtd Ref IRQs 0 10 N 0 4 5 6 7 10 11 14 15 pci_link7: Links after initial validation: Index IRQ Rtd Ref IRQs 0 10 N 0 4 5 6 7 10 11 14 15 pci_link7: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 4 5 6 7 10 11 14 15 ACPI timer: 1/0 1/0 1/0 1/0 1/0 1/0 1/0 1/0 1/0 1/0 -> 10 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 cpu0: <ACPI CPU> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pci0: physical bus=0 found-> vendor=0x8086, dev=0x3590, revid=0x0c bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0106, statreg=0x0090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x3591, revid=0x0c bus=0, slot=0, func=1 class=ff-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0100, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x3594, revid=0x0c bus=0, slot=1, func=0 class=08-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0102, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=5 MSI supports 2 messages map[10]: type 1, range 32, base dd000000, size 12, enabled pcib0: matched entry for 0.1.INTA pcib0: slot 1 INTA hardwired to IRQ 16 found-> vendor=0x8086, dev=0x3595, revid=0x0c bus=0, slot=2, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x0010, cachelnsz=8 (dwords) lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) intpin=a, irq=5 pcib0: matched entry for 0.2.INTA pcib0: slot 2 INTA hardwired to IRQ 16 found-> vendor=0x8086, dev=0x3597, revid=0x0c bus=0, slot=4, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x4018, cachelnsz=8 (dwords) lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) intpin=a, irq=5 pcib0: matched entry for 0.4.INTA pcib0: slot 4 INTA hardwired to IRQ 16 found-> vendor=0x8086, dev=0x3599, revid=0x0c bus=0, slot=6, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x4018, cachelnsz=8 (dwords) lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) intpin=a, irq=5 pcib0: matched entry for 0.6.INTA pcib0: slot 6 INTA hardwired to IRQ 16 found-> vendor=0x8086, dev=0x24d2, revid=0x02 bus=0, slot=29, func=0 class=0c-03-00, hdrtype=0x00, mfdev=1 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=5 map[20]: type 4, range 32, base 00001400, size 5, enabled pcib0: matched entry for 0.29.INTA pcib0: slot 29 INTA hardwired to IRQ 16 found-> vendor=0x8086, dev=0x24d4, revid=0x02 bus=0, slot=29, func=1 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=11 map[20]: type 4, range 32, base 00001420, size 5, enabled pcib0: matched entry for 0.29.INTB pcib0: slot 29 INTB hardwired to IRQ 19 found-> vendor=0x8086, dev=0x24d7, revid=0x02 bus=0, slot=29, func=2 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=c, irq=7 map[20]: type 4, range 32, base 00001440, size 5, enabled pcib0: matched entry for 0.29.INTC pcib0: slot 29 INTC hardwired to IRQ 18 found-> vendor=0x8086, dev=0x24de, revid=0x02 bus=0, slot=29, func=3 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=5 map[20]: type 4, range 32, base 00001460, size 5, enabled pcib0: matched entry for 0.29.INTA pcib0: slot 29 INTA hardwired to IRQ 16 found-> vendor=0x8086, dev=0x24dd, revid=0x02 bus=0, slot=29, func=7 class=0c-03-20, hdrtype=0x00, mfdev=0 cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=d, irq=10 powerspec 2 supports D0 D3 current D0 map[10]: type 1, range 32, base dd001000, size 10, enabled pcib0: matched entry for 0.29.INTD pcib0: slot 29 INTD hardwired to IRQ 23 found-> vendor=0x8086, dev=0x244e, revid=0xc2 bus=0, slot=30, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x0080, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x0c (3000 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x24d0, revid=0x02 bus=0, slot=31, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x010f, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x24db, revid=0x02 bus=0, slot=31, func=1 class=01-01-8a, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0288, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 map[20]: type 4, range 32, base 000014a0, size 4, enabled map[24]: type 1, range 32, base 00000000, size 10, enabled found-> vendor=0x8086, dev=0x24d3, revid=0x02 bus=0, slot=31, func=3 class=0c-05-00, hdrtype=0x00, mfdev=0 cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=10 map[20]: type 4, range 32, base 00001100, size 5, enabled pcib0: matched entry for 0.31.INTB pcib0: slot 31 INTB hardwired to IRQ 17 pci0: <unknown> at device 0.1 (no driver attached) pci0: <base peripheral> at device 1.0 (no driver attached) pcib1: <ACPI PCI-PCI bridge> irq 16 at device 2.0 on pci0 pcib1: secondary bus 1 pcib1: subordinate bus 3 pcib1: I/O decode 0x2000-0x3fff pcib1: memory decode 0xdd100000-0xdd3fffff pcib1: prefetched decode 0xfff00000-0xfffff pcib1: could not get PCI interrupt routing table for \\_SB_.PCI0.PEX0 - AE_NOT_FOUND pci1: <ACPI PCI bus> on pcib1 pci1: physical bus=1 found-> vendor=0x8086, dev=0x0329, revid=0x09 bus=1, slot=0, func=0 class=06-04-00, hdrtype=0x01, mfdev=1 cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x0326, revid=0x09 bus=1, slot=0, func=1 class=08-00-20, hdrtype=0x00, mfdev=1 cmdreg=0x0106, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) powerspec 2 supports D0 D3 current D0 map[10]: type 1, range 32, base dd100000, size 12, enabled pcib1: (null) requested memory range 0xdd100000-0xdd100fff: good found-> vendor=0x8086, dev=0x032a, revid=0x09 bus=1, slot=0, func=2 class=06-04-00, hdrtype=0x01, mfdev=1 cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x0327, revid=0x09 bus=1, slot=0, func=3 class=08-00-20, hdrtype=0x00, mfdev=1 cmdreg=0x0106, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) powerspec 2 supports D0 D3 current D0 map[10]: type 1, range 32, base dd101000, size 12, enabled pcib1: (null) requested memory range 0xdd101000-0xdd101fff: good pcib2: <ACPI PCI-PCI bridge> at device 0.0 on pci1 pcib2: secondary bus 2 pcib2: subordinate bus 2 pcib2: I/O decode 0x2000-0x2fff pcib2: memory decode 0xdd200000-0xdd2fffff pcib2: prefetched decode 0xfff00000-0xfffff pci2: <ACPI PCI bus> on pcib2 pci2: physical bus=2 found-> vendor=0x11ab, dev=0x6041, revid=0x03 bus=2, slot=2, func=0 class=01-04-00, hdrtype=0x00, mfdev=0 cmdreg=0x0317, statreg=0x02b0, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=5 powerspec 2 supports D0 D3 current D0 MSI supports 1 message, 64 bit map[10]: type 1, range 64, base dd200000, size 20, enabled pcib2: (null) requested memory range 0xdd200000-0xdd2fffff: good pcib1: (null) requested memory range 0xdd200000-0xdd2fffff: good map[18]: type 4, range 32, base 00002000, size 8, enabled pcib2: (null) requested I/O range 0x2000-0x20ff: in range pcib1: (null) requested I/O range 0x2000-0x20ff: in range pcib2: matched entry for 2.2.INTA pcib2: slot 2 INTA hardwired to IRQ 32 atapci0: <Marvell 88SX6041 SATA300 controller> port 0x2000-0x20ff mem 0xdd200000-0xdd2fffff irq 32 at device 2.0 on pci2 ioapic1: routing intpin 8 (PCI IRQ 32) to vector 49 atapci0: [MPSAFE] atapci0: Reserved 0x100000 bytes for rid 0x10 type 3 at 0xdd200000 ata2: <ATA channel 0> on atapci0 ata2: SATA connect ready time=0ms ata2: sata_connect devices=0x1<ATA_MASTER> ata2: [MPSAFE] ata3: <ATA channel 1> on atapci0 ata3: SATA connect ready time=0ms ata3: sata_connect devices=0x1<ATA_MASTER> ata3: [MPSAFE] ata4: <ATA channel 2> on atapci0 ata4: SATA connect ready time=0ms ata4: sata_connect devices=0x1<ATA_MASTER> ata4: [MPSAFE] ata5: <ATA channel 3> on atapci0 ata5: SATA connect ready time=0ms ata5: sata_connect devices=0x1<ATA_MASTER> ata5: [MPSAFE] pci1: <base peripheral, interrupt controller> at device 0.1 (no driver attached) pcib3: <ACPI PCI-PCI bridge> at device 0.2 on pci1 pcib3: secondary bus 3 pcib3: subordinate bus 3 pcib3: I/O decode 0x3000-0x3fff pcib3: memory decode 0xdd300000-0xdd3fffff pcib3: prefetched decode 0xfff00000-0xfffff pci3: <ACPI PCI bus> on pcib3 pci3: physical bus=3 found-> vendor=0x8086, dev=0x1079, revid=0x03 bus=3, slot=2, func=0 class=02-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0117, statreg=0x0230, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns) intpin=a, irq=7 powerspec 2 supports D0 D3 current D0 MSI supports 1 message, 64 bit map[10]: type 1, range 64, base dd300000, size 17, enabled pcib3: (null) requested memory range 0xdd300000-0xdd31ffff: good pcib1: (null) requested memory range 0xdd300000-0xdd31ffff: good map[20]: type 4, range 32, base 00003000, size 6, enabled pcib3: (null) requested I/O range 0x3000-0x303f: in range pcib1: (null) requested I/O range 0x3000-0x303f: in range pcib3: matched entry for 3.2.INTA pcib3: slot 2 INTA hardwired to IRQ 54 found-> vendor=0x8086, dev=0x1079, revid=0x03 bus=3, slot=2, func=1 class=02-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0117, statreg=0x0230, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns) intpin=b, irq=11 powerspec 2 supports D0 D3 current D0 MSI supports 1 message, 64 bit map[10]: type 1, range 64, base dd320000, size 17, enabled pcib3: (null) requested memory range 0xdd320000-0xdd33ffff: good pcib1: (null) requested memory range 0xdd320000-0xdd33ffff: good map[20]: type 4, range 32, base 00003040, size 6, enabled pcib3: (null) requested I/O range 0x3040-0x307f: in range pcib1: (null) requested I/O range 0x3040-0x307f: in range pcib3: matched entry for 3.2.INTB pcib3: slot 2 INTB hardwired to IRQ 55 em0: <Intel(R) PRO/1000 Network Connection Version - 3.2.18> port 0x3000-0x303f mem 0xdd300000-0xdd31ffff irq 54 at device 2.0 on pci3 em0: Reserved 0x20000 bytes for rid 0x10 type 3 at 0xdd300000 em0: Reserved 0x40 bytes for rid 0x20 type 4 at 0x3000 ioapic2: routing intpin 6 (PCI IRQ 54) to vector 50 em0: [MPSAFE] em0: bpf attached em0: Ethernet address: 00:00:00:00:00:00 em0: Speed:N/A Duplex:N/A em1: <Intel(R) PRO/1000 Network Connection Version - 3.2.18> port 0x3040-0x307f mem 0xdd320000-0xdd33ffff irq 55 at device 2.1 on pci3 em1: Reserved 0x20000 bytes for rid 0x10 type 3 at 0xdd320000 em1: Reserved 0x40 bytes for rid 0x20 type 4 at 0x3040 ioapic2: routing intpin 7 (PCI IRQ 55) to vector 51 em1: [MPSAFE] em1: bpf attached em1: Ethernet address: 00:00:00:00:00:00 em1: Speed:N/A Duplex:N/A pci1: <base peripheral, interrupt controller> at device 0.3 (no driver attached) pcib4: <ACPI PCI-PCI bridge> irq 16 at device 4.0 on pci0 pcib4: secondary bus 4 pcib4: subordinate bus 4 pcib4: I/O decode 0xf000-0xfff pcib4: memory decode 0xfff00000-0xfffff pcib4: prefetched decode 0xfff00000-0xfffff pci4: <ACPI PCI bus> on pcib4 pci4: physical bus=4 pcib5: <ACPI PCI-PCI bridge> irq 16 at device 6.0 on pci0 pcib5: secondary bus 5 pcib5: subordinate bus 5 pcib5: I/O decode 0xf000-0xfff pcib5: memory decode 0xfff00000-0xfffff pcib5: prefetched decode 0xfff00000-0xfffff pci5: <ACPI PCI bus> on pcib5 pci5: physical bus=5 uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0x1400-0x141f irq 16 at device 29.0 on pci0 uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1400 ioapic0: routing intpin 16 (PCI IRQ 16) to vector 52 uhci0: [GIANT-LOCKED] usb0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0x1420-0x143f irq 19 at device 29.1 on pci0 uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1420 ioapic0: routing intpin 19 (PCI IRQ 19) to vector 53 uhci1: [GIANT-LOCKED] usb1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0x1440-0x145f irq 18 at device 29.2 on pci0 uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1440 ioapic0: routing intpin 18 (PCI IRQ 18) to vector 54 uhci2: [GIANT-LOCKED] usb2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2 usb2: USB revision 1.0 uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port 0x1460-0x147f irq 16 at device 29.3 on pci0 uhci3: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1460 uhci3: [GIANT-LOCKED] usb3: <Intel 82801EB (ICH5) USB controller USB-D> on uhci3 usb3: USB revision 1.0 uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub3: 2 ports with 2 removable, self powered ehci0: <Intel 82801EB/R (ICH5) USB 2.0 controller> mem 0xdd001000-0xdd0013ff irq 23 at device 29.7 on pci0 ehci0: Reserved 0x400 bytes for rid 0x10 type 3 at 0xdd001000 ioapic0: routing intpin 23 (PCI IRQ 23) to vector 55 ehci0: [GIANT-LOCKED] usb4: EHCI version 1.0 usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3 usb4: <Intel 82801EB/R (ICH5) USB 2.0 controller> on ehci0 usb4: USB revision 2.0 uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 uhub4: 8 ports with 8 removable, self powered pcib6: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pcib6: secondary bus 6 pcib6: subordinate bus 6 pcib6: I/O decode 0x4000-0x4fff pcib6: memory decode 0xdd400000-0xdeffffff pcib6: prefetched decode 0xfff00000-0xfffff pcib6: Subtractively decoded bridge. pci6: <ACPI PCI bus> on pcib6 pci6: physical bus=6 found-> vendor=0x1002, dev=0x4752, revid=0x27 bus=6, slot=1, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0087, statreg=0x0290, cachelnsz=8 (dwords) lattimer=0x42 (1980 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base de000000, size 24, enabled pcib6: (null) requested memory range 0xde000000-0xdeffffff: good map[14]: type 4, range 32, base 00004000, size 8, enabled pcib6: (null) requested I/O range 0x4000-0x40ff: in range map[18]: type 1, range 32, base dd400000, size 12, enabled pcib6: (null) requested memory range 0xdd400000-0xdd400fff: good pcib6: matched entry for 6.1.INTA pcib6: slot 1 INTA hardwired to IRQ 17 pci6: <display, VGA> at device 1.0 (no driver attached) isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci1: <Intel ICH5 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x14a0-0x14af at device 31.1 on pci0 atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0x14a0 ata0: <ATA channel 0> on atapci1 atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0 atapci1: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6 ata0: reset tp1 mask=03 ostat0=00 ostat1=00 ata0: stat0=0x01 err=0x01 lsb=0x01 msb=0x01 ata0: stat1=0x01 err=0x01 lsb=0x01 msb=0x01 ata0: reset tp2 stat0=01 stat1=01 devices=0x0 ioapic0: routing intpin 14 (ISA IRQ 14) to vector 56 ata0: [MPSAFE] ata1: <ATA channel 1> on atapci1 atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170 atapci1: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376 ata1: reset tp1 mask=03 ostat0=00 ostat1=50 ata1: stat0=0x01 err=0x01 lsb=0x01 msb=0x01 ata1: stat1=0x00 err=0x01 lsb=0x14 msb=0xeb ata1: reset tp2 stat0=01 stat1=00 devices=0x8<ATAPI_SLAVE> ioapic0: routing intpin 15 (ISA IRQ 15) to vector 57 ata1: [MPSAFE] pci0: <serial bus, SMBus> at device 31.3 (no driver attached) acpi_button0: <Power Button> on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0047 atkbd: keyboard ID 0x41ab (2) kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 ioapic0: routing intpin 1 (ISA IRQ 1) to vector 58 atkbd0: [GIANT-LOCKED] psm0: unable to allocate IRQ psmcpnp0: <PS/2 mouse port> irq 12 on acpi0 psm0: current command byte:0047 psm0: failed to reset the aux device. sio0: irq maps: 0x8ca1 0x8cb1 0x8ca1 0x8ca1 sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 sio0: type 16550A ioapic0: routing intpin 4 (ISA IRQ 4) to vector 59 sio1: irq maps: 0x8ca1 0x8ca9 0x8ca1 0x8ca1 sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0 sio1: type 16550A ioapic0: routing intpin 3 (ISA IRQ 3) to vector 60 fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 fdc0: ic_type 90 part_id 73 ioapic0: routing intpin 6 (ISA IRQ 6) to vector 61 fdc0: [MPSAFE] fdc0: [FAST] fd0: <1440-KB 3.5" drive> on fdc0 drive 0 ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it atkbdc: atkbdc0 already exists; skipping it fdc: fdc0 already exists; skipping it sc: sc0 already exists; skipping it sio: sio0 already exists; skipping it sio: sio1 already exists; skipping it vga: vga0 already exists; skipping it pnp_identify: Trying Read_Port at 203 pnp_identify: Trying Read_Port at 243 pnp_identify: Trying Read_Port at 283 pnp_identify: Trying Read_Port at 2c3 pnp_identify: Trying Read_Port at 303 pnp_identify: Trying Read_Port at 343 pnp_identify: Trying Read_Port at 383 pnp_identify: Trying Read_Port at 3c3 PNP Identify complete isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices pmtimer0 on isa0 orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc8fff,0xc9000-0xcd7ff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sc0: fb0, kbd1, terminal emulator: sc (syscons terminal) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 adv0: not probed (disabled) aha0: not probed (disabled) aic0: not probed (disabled) bt0: not probed (disabled) cs0: not probed (disabled) ed0: not probed (disabled) fe0: not probed (disabled) ie0: not probed (disabled) lnc0: not probed (disabled) ppc0 failed to probe at irq 7 on isa0 sio2: not probed (disabled) sio3: not probed (disabled) sn0: not probed (disabled) vt0: not probed (disabled) isa_probe_children: probing PnP devices Device configuration finished. Reducing kern.maxvnodes 134590 -> 100000 procfs registered lapic: Divisor 2, Frequency 100003698 hz Timecounter "TSC" frequency 3219347072 Hz quality 800 Timecounters tick every 1.000 msec lo0: bpf attached ata1-slave: pio=PIO4 wdma=WDMA2 udma=UDMA66 cable=40 wire acd0: setting PIO4 on ICH5 chip acd0: DMA limited to UDMA33, controller found non-ATA66 cable acd0: setting UDMA33 on ICH5 chip acd0: <MATSHITADVD-ROM SR-8178/PZ16> DVDROM drive at ata1 as slave acd0: read 4125KB/s (4125KB/s), 256KB buffer, UDMA33 acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet acd0: Writes: acd0: Audio: play, 255 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: CD-ROM 120mm data disc ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire ad4: 143089MB <WDC WD1500ADFD-00NLR1 20.07P20> at ata2-master SATA150 ad4: 293046768 sectors [290721C/16H/63S] 16 sectors/interrupt 1 depth queue ad4: Adaptec check1 failed ad4: LSI (v3) check1 failed ad4: LSI (v2) check1 failed ad4: FreeBSD check1 failed ata3-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire ad6: 143089MB <WDC WD1500ADFD-00NLR1 20.07P20> at ata3-master SATA150 ad6: 293046768 sectors [290721C/16H/63S] 16 sectors/interrupt 1 depth queue ad6: Adaptec check1 failed ad6: LSI (v3) check1 failed ad6: LSI (v2) check1 failed ad6: FreeBSD check1 failed ata4-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire ad8: 143089MB <WDC WD1500ADFD-00NLR1 20.07P20> at ata4-master SATA150 ad8: 293046768 sectors [290721C/16H/63S] 16 sectors/interrupt 1 depth queue ad8: Adaptec check1 failed ad8: LSI (v3) check1 failed ad8: LSI (v2) check1 failed ad8: FreeBSD check1 failed ata5-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire ad10: 143089MB <WDC WD1500ADFD-00NLR1 20.07P20> at ata5-master SATA150 ad10: 293046768 sectors [290721C/16H/63S] 16 sectors/interrupt 1 depth queue ad10: Adaptec check1 failed ad10: LSI (v3) check1 failed ad10: LSI (v2) check1 failed ad10: FreeBSD check1 failed ATA PseudoRAID loaded GEOM: new disk ad4 GEOM: new disk ad6 GEOM: new disk ad8 GEOM: new disk ad10 GEOM_MIRROR: Device gm0 created (id=4151717145). GEOM_MIRROR: Device gm0: provider ad4 detected. GEOM_MIRROR: Device gm0: provider ad6 detected. GEOM_MIRROR: Device gm0: provider ad6 activated. GEOM_MIRROR: Device gm0: provider ad4 activated. GEOM_MIRROR: Device gm0: provider mirror/gm0 launched. GEOM_MIRROR: Device gm1 created (id=429699985). GEOM_MIRROR: Device gm1: provider ad8 detected. ad10: WARNING - READ_DMA48 soft error (ECC corrected) LBA=293046767 GEOM_MIRROR: Device gm1: provider ad10 detected. GEOM_MIRROR: Device gm1: provider ad10 activated. GEOM_MIRROR: Device gm1: provider ad8 activated. GEOM_MIRROR: Device gm1: provider mirror/gm1 launched. ad10: WARNING - READ_DMA soft error (ECC corrected) LBA=225443903 Trying to mount root from ufs:/dev/mirror/gm0s1a start_init: trying /sbin/init ad10: WARNING - READ_DMA soft error (ECC corrected) LBA=64 ad10: WARNING - READ_DMA soft error (ECC corrected) LBA=12409711 --------------010300000005080707060406--
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?4484A302.8050107>