Date: Thu, 13 Dec 2007 12:53:45 +0900 From: Randy Bush <randy@psg.com> To: FreeBSD Net <freebsd-net@freebsd.org> Cc: "Bruce M. Simpson" <bms@FreeBSD.org> Subject: Re: ifconfig: BRDGADD vr1: Invalid argument Message-ID: <4760ACC9.70305@psg.com> In-Reply-To: <47602195.9050602@psg.com> References: <Pine.BSF.3.96.1071212163530.611D-100000@gaia.nimnet.asn.au> <475F744F.7030003@psg.com> <475FD764.8090402@FreeBSD.org> <47602195.9050602@psg.com>
next in thread | previous in thread | raw e-mail | index | archive | help
ok, i have bridging working (kernel/userland version skew likely culprit, thanks max),
except that ath0 does not seem to completely bridge. bms may have warned me in saying
> although you won't get the 802.11 frames bridged.
---
the problem:
o hosts on vr1, vr2, and vr3 get dhcp addresses and can see the world
o host on ath0 can not get dhcp address
- soekris sees dhcp request and responds
- response not seen by anyone on wireless
- tcpdump says dhcpd is sending the response (see below)
the plan:
Soekris 5501
.-----------------------.
| |
| b ---ath0|
| r | LAN
external | i --- vr1|
------------|vr0---NAT---- d | DHCP
WAN | g --- vr2|
| e | Clients
| 0 --- vr3|
| |
`-----------------------'
vr0 gets address via DHCP from external link
bridge0 is hard coded as 192.168.0.1/24
dhcpd runs on bridge0 for the range 192.168.0.100-199 to feed the LAN.
---
from /etc/rc.conf:
firewall_enable=YES # Set to YES to enable firewall functionality
firewall_type="/etc/ipfw.rules" # Firewall type (see /etc/rc.firewall)
firewall_quiet=YES # Set to YES to suppress rule display
firewall_logging=YES # Set to YES to enable events logging
ifconfig_vr0=DHCP
cloned_interfaces=bridge0
ifconfig_bridge0="192.168.0.1 addm vr1 addm vr2 addm vr3 up addm ath0"
ifconfig_vr1=up
ifconfig_vr2=up
ifconfig_vr3=up
ifconfig_ath0="channel 4 ssid rgnet-aden wep wepkey x mediaopt hostap up"
gateway_enable=YES
---
from /etc/sysctl.conf:
# nat
net.inet.ip.fw.one_pass=0
# bridging
#net.link.ether.ipfw=1 -- uncomment and connectivity on vr0 is lost
net.link.bridge.ipfw=1
net.link.bridge.ipfw_arp=1
# ath bridging
net.inet.ip.check_interface=0
---
# ifconfig -a
vr0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=b<RXCSUM,TXCSUM,VLAN_MTU>
ether 00:00:24:c8:b3:28
inet 666.42.86.171 netmask 0xffffffc0 broadcast 666.42.86.191
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
vr1: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=9<RXCSUM,VLAN_MTU>
ether 00:00:24:c8:b3:29
media: Ethernet autoselect (none)
status: no carrier
vr2: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=9<RXCSUM,VLAN_MTU>
ether 00:00:24:c8:b3:2a
media: Ethernet autoselect (none)
status: no carrier
vr3: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=9<RXCSUM,VLAN_MTU>
ether 00:00:24:c8:b3:2b
media: Ethernet autoselect (none)
status: no carrier
ath0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500
ether 00:0b:6b:83:59:25
media: IEEE 802.11 Wireless Ethernet autoselect <hostap> (autoselect <hostap>)
status: associated
ssid rgnet-aden channel 4 (2427 Mhz 11g) bssid 00:0b:6b:83:59:25
authmode OPEN privacy ON deftxkey UNDEF wepkey 1:104-bit txpower 31.5
scanvalid 60 bgscan bgscanintvl 300 bgscanidle 250 roam:rssi11g 7
roam:rate11g 5 protmode CTS burst dtimperiod 1
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x6
inet6 ::1 prefixlen 128
inet 127.0.0.1 netmask 0xff000000
bridge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
ether c6:75:12:20:d9:c2
inet 192.168.0.1 netmask 0xffffff00 broadcast 192.168.0.255
id 00:00:00:00:00:00 priority 32768 hellotime 2 fwddelay 15
maxage 20 holdcnt 6 proto rstp maxaddr 100 timeout 1200
root id 00:00:00:00:00:00 priority 32768 ifcost 0 port 0
member: ath0 flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP>
ifmaxaddr 0 port 5 priority 128 path cost 370370
member: vr3 flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP>
ifmaxaddr 0 port 4 priority 128 path cost 200000
member: vr2 flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP>
ifmaxaddr 0 port 3 priority 128 path cost 55
member: vr1 flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP>
ifmaxaddr 0 port 2 priority 128 path cost 55
---
the tcpdump -i ath0
03:48:29.717236 00:18:de:21:76:c9 (oui Unknown) > Broadcast Null Supervisory, Receiver not Ready, rcv seq 64, Flags [Poll], length 6
03:48:29.717244 00:18:de:21:76:c9 (oui Unknown) > Broadcast Null Supervisory, Receiver not Ready, rcv seq 64, Flags [Poll], length 6
03:48:30.192604 IP 0.0.0.0.bootpc > 255.255.255.255.bootps: BOOTP/DHCP, Request from 00:18:de:21:76:c9 (oui Unknown), length 300
03:48:30.192613 IP 0.0.0.0.bootpc > 255.255.255.255.bootps: BOOTP/DHCP, Request from 00:18:de:21:76:c9 (oui Unknown), length 300
03:48:30.193467 IP 192.168.0.1.bootps > test.psg.com.bootpc: BOOTP/DHCP, Reply, length 300
03:48:33.192787 IP 0.0.0.0.bootpc > 255.255.255.255.bootps: BOOTP/DHCP, Request from 00:18:de:21:76:c9 (oui Unknown), length 300
03:48:33.192799 IP 0.0.0.0.bootpc > 255.255.255.255.bootps: BOOTP/DHCP, Request from 00:18:de:21:76:c9 (oui Unknown), length 300
03:48:33.194067 IP 192.168.0.1.bootps > test.psg.com.bootpc: BOOTP/DHCP, Reply, length 300
---
randy
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?4760ACC9.70305>