Date: Mon, 06 Jul 2009 17:07:40 -0600 From: ToyoRunner <toyorunner@gmail.com> To: Anton Shterenlikht <mexas@bristol.ac.uk> Cc: freebsd-ia64@freebsd.org Subject: Re: SOLVED: Re: cannot partition HP 73GB disks Message-ID: <4A5283BC.2000107@gmail.com> In-Reply-To: <20090706224435.GA23791@mech-cluster238.men.bris.ac.uk> References: <20090706201733.GA17827@mech-cluster238.men.bris.ac.uk> <20090706205125.GA18002@mech-cluster238.men.bris.ac.uk> <20090706222229.GA23689@mech-cluster238.men.bris.ac.uk> <20090706224435.GA23791@mech-cluster238.men.bris.ac.uk>
next in thread | previous in thread | raw e-mail | index | archive | help
Anton Shterenlikht wrote: > On Mon, Jul 06, 2009 at 11:22:29PM +0100, Anton Shterenlikht wrote: > >> On Mon, Jul 06, 2009 at 09:51:25PM +0100, Anton Shterenlikht wrote: >> >>> On Mon, Jul 06, 2009 at 09:17:33PM +0100, Anton Shterenlikht wrote: >>> >>>> Trying to install FBSD 8.0-snapshot 200906 on 73GB HP scsi disks: >>>> >>>> da0 at mpt0 bus 0 target 0 lun 0 >>>> da0: <HP 73.4G ST373454LC HPC2> Fixed Direct Access SCSI-3 device >>>> da0: 320.000MB/s transfers (160.000MHz, offset 63, 16bit) >>>> da0: Command Queueing Enabled >>>> da0: 70007MB (143374738 512 byte sectors: 255H 63S/T 8924C) >>>> da1 at mpt0 bus 0 target 1 lun 0 >>>> da1: <HP 73.4G ST373454LC HPC2> Fixed Direct Access SCSI-3 device >>>> da1: 320.000MB/s transfers (160.000MHz, offset 63, 16bit) >>>> da1: Command Queueing Enabled >>>> da1: 70007MB (143374738 512 byte sectors: 255H 63S/T 8924C) >>>> >>>> >>>> and partition name appears only as "X" in disklabel editor: >>>> >>>> >>>> FreeBSD Disklabel Editor >>>> >>>> Disk: da0 Free: 0 blocks (0MB) >>>> >>>> Part Mount Size Newfs Part Mount Size Newfs >>>> ---- ----- ---- ----- ---- ----- ---- ----- >>>> X /efi 100MB EFI Y >>>> X / 512MB UFS2 Y >>>> X swap 4055MB SWAP >>>> X /var 3051MB UFS2+S Y >>>> X /tmp 512MB UFS2+S Y >>>> X /usr 61776MB UFS2+S Y >>>> >>>> >>>> automatic or manual - doesn't matter, all partitions are named X, >>>> and the installation fails with "cannot create partition /dev/X" or >>>> similar. >>>> >>>> With some seagate 17GB disks works fine. >>>> >>>> Please advise >>>> >>> This thread mentiones a somewhat similar problem >>> - the installation program cannot "write data to >>> disk" in 5.2 and 6.1. It's on zx6000 itanium, >>> which is very similar to my rx2600, and again >>> 73GB scsi disks are used: >>> >>> http://lists.freebsd.org/pipermail/freebsd-ia64/2006-December/001191.html >>> >>> no solution was found then. >>> >> Using livefs cd I was able to gpart one disk. Then booting from the >> installation disk1 I can set: >> >> FreeBSD Disklabel Editor >> >> Disk: da0 Free: 0 blocks (0MB) >> >> Part Mount Size Newfs Part Mount Size Newfs >> ---- ----- ---- ----- ---- ----- ---- ----- >> da0p1 /efi 400MB EFI N >> da0p2 / 512MB UFS2 N >> da0p3 swap 2048MB SWAP >> da0p4 /var 1024MB UFS2+S N >> da0p5 /tmp 1024MB UFS2+S N >> da0p6 /usr 64999MB UFS2+S N >> >> >> However, when the installaiton starts I get several warnings, something >> about fsck returning error 8 on checking root partition, and then this >> error: >> >> Error mounting /dev/da0p2 on /mnt : Invalid argument >> > > In the partitioning part of the installation program I had to delete > all partitions and create them again. Somehow this time round partition > names were created fine, and the installation then proceeded ok. > > It seems all that was needed was > gpart create -s gpt da0 > > from the livefs, then the installation cd could be used. > > not sure why this happened with 73GB disks and didn't happen with 17GB disks. > > I have encountered the same problem. I don't know what causes it but basically if you want to make a partition change in the installer you have to remove all the existing partitions and re add them. The installer will not newfs the existing partitions. It fails the with "Invalid argument" error. BTW, did you have any luck with gmirror?
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?4A5283BC.2000107>