Date: Wed, 12 Aug 2009 14:14:04 +0200 From: Rick Wezenaar <rick@mitranet.nl> To: freebsd-multimedia@freebsd.org Subject: Re: acd0: setting up DMA failed Message-ID: <4A82B20C.6030703@mitranet.nl> In-Reply-To: <4A7EE1A2.6000208@mitranet.nl> References: <4A7EE1A2.6000208@mitranet.nl>
next in thread | previous in thread | raw e-mail | index | archive | help
*BUMP* Anyone ? Rick Wezenaar wrote: > Hello all, > > I am getting the following error on my DVDRW drive: > > Aug 9 10:07:18 phenomium kernel: acd0: FAILURE - READ_BIG MEDIUM ERROR > asc=0x02 ascq=0x00 > Aug 9 10:07:18 phenomium kernel: (cd0:ata2:0:0:0): READ(10). CDB: 28 0 > 0 5 77 e0 0 0 1 0 > Aug 9 10:07:18 phenomium kernel: (cd0:ata2:0:0:0): CAM Status: SCSI > Status Error > Aug 9 10:07:18 phenomium kernel: (cd0:ata2:0:0:0): SCSI Status: Check > Condition > Aug 9 10:07:18 phenomium kernel: (cd0:ata2:0:0:0): MEDIUM ERROR > info:577e0 asc:2,0 > Aug 9 10:07:18 phenomium kernel: (cd0:ata2:0:0:0): No seek complete > Aug 9 10:07:18 phenomium kernel: (cd0:ata2:0:0:0): Retrying Command > (per Sense Data) > Aug 9 10:07:18 phenomium kernel: ata3: FAILURE - zero length DMA > transfer attempted > Aug 9 10:07:18 phenomium kernel: acd0: setting up DMA failed > Aug 9 10:07:19 phenomium kernel: ata3: FAILURE - zero length DMA > transfer attempted > etc. > > Also, k3b and xcdroast seem to have problems detecting the drive. They > keep complaining that they can not find an optical device. (which should > be /dev/cd0). > > Information about my system: > > uname: > FreeBSD phenomium.mitranet.nl 7.2-RELEASE FreeBSD 7.2-RELEASE #0: Fri > Aug 7 01:22:21 CEST 2009 > root@phenomium.mitranet.nl:/usr/obj/usr/src/sys/PHENOMIUM02 amd64 > > kernel (excerpt): > cpu HAMMER > ident PHENOMIUM02 > options QUOTA > options IPFIREWALL > options IPFIREWALL_VERBOSE > options DUMMYNET > options HZ=1000 > device atapicam > device ata > device atadisk > device ataraid > device atapicd > device atapifd > device atapist > options ATA_STATIC_ID > device scbus > device ch > device da > device sa > device cd > device pass > > $ ls -la /dev/*cd* > crw-rw-rw- 1 root operator 0, 99 Aug 9 02:42 acd0 > crw-r----- 1 root operator 0, 126 Aug 9 02:42 acd0t01 > crw-rw-rw- 1 root operator 0, 118 Aug 9 02:42 cd0 > $ > > dmesg: > Copyright (c) 1992-2009 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 7.2-RELEASE #0: Fri Aug 7 01:22:21 CEST 2009 > root@phenomium.mitranet.nl:/usr/obj/usr/src/sys/PHENOMIUM02 > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: AMD Phenom(tm) 9850 Quad-Core Processor (2500.19-MHz K8-class CPU) > Origin = "AuthenticAMD" Id = 0x100f23 Stepping = 3 > > Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> > > Features2=0x802009<SSE3,MON,CX16,<b23>> > AMD > Features=0xee500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM,3DNow!+,3DNow!> > AMD > Features2=0x7ff<LAHF,CMP,SVM,ExtAPIC,CR8,<b5>,<b6>,<b7>,Prefetch,<b9>,<b10>> > > TSC: P-state invariant > Cores per package: 4 > usable memory = 4280946688 (4082 MB) > avail memory = 4108361728 (3918 MB) > ACPI APIC Table: <122407 APIC1648> > FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs > cpu0 (BSP): APIC ID: 0 > cpu1 (AP): APIC ID: 1 > cpu2 (AP): APIC ID: 2 > cpu3 (AP): APIC ID: 3 > ioapic0 <Version 2.1> irqs 0-23 on motherboard > kbd1 at kbdmux0 > acpi0: <122407 RSDT1648> on motherboard > acpi0: [ITHREAD] > acpi0: Power Button (fixed) > acpi0: reservation of ffb80000, 80000 (3) failed > acpi0: reservation of fff00000, 100000 (3) failed > acpi0: reservation of 0, a0000 (3) failed > acpi0: reservation of 100000, cff00000 (3) failed > ACPI HPET table warning: Sequence is non-zero (2) > Timecounter "ACPI-safe" frequency 3579545 Hz quality 850 > acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 > acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on > acpi0 > Timecounter "HPET" frequency 14318180 Hz quality 900 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0 > pci1: <ACPI PCI bus> on pcib1 > vgapci0: <VGA-compatible display> port 0xc000-0xc0ff mem > 0xd0000000-0xdfffffff,0xfe9f0000-0xfe9fffff irq 18 at device 0.0 on pci1 > hdac0: <ATI RV630 High Definition Audio Controller> mem > 0xfe9ec000-0xfe9effff irq 19 at device 0.1 on pci1 > hdac0: HDA Driver Revision: 20090329_0131 > hdac0: [ITHREAD] > pcib2: <ACPI PCI-PCI bridge> at device 6.0 on pci0 > pci2: <ACPI PCI bus> on pcib2 > re0: <RealTek 8168/8168B/8168C/8168CP/8168D/8111B/8111C/8111CP PCIe > Gigabit Ethernet> port 0xd800-0xd8ff mem 0xfeaff000-0xfeafffff irq 18 at > device 0.0 on pci2 > re0: Using 1 MSI messages > re0: Chip rev. 0x38000000 > re0: MAC rev. 0x00000000 > miibus0: <MII bus> on re0 > rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus0 > rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, > 1000baseT-FDX, auto > re0: Ethernet address: 00:1d:92:85:b3:ad > re0: [FILTER] > atapci0: <ATI IXP600 SATA300 controller> port > 0xb000-0xb007,0xa000-0xa003,0x9000-0x9007,0x8000-0x8003,0x7000-0x700f > mem 0xfe8ff800-0xfe8ffbff irq 22 at device 18.0 on pci0 > atapci0: [ITHREAD] > atapci0: AHCI Version 01.10 controller with 4 ports detected > ata2: <ATA channel 0> on atapci0 > ata2: [ITHREAD] > ata3: <ATA channel 1> on atapci0 > ata3: [ITHREAD] > ata4: <ATA channel 2> on atapci0 > ata4: [ITHREAD] > ata5: <ATA channel 3> on atapci0 > ata5: [ITHREAD] > ohci0: <OHCI (generic) USB controller> mem 0xfe8fe000-0xfe8fefff irq 16 > at device 19.0 on pci0 > ohci0: [GIANT-LOCKED] > ohci0: [ITHREAD] > usb0: OHCI version 1.0, legacy support > usb0: SMM does not respond, resetting > usb0: <OHCI (generic) USB controller> on ohci0 > usb0: USB revision 1.0 > uhub0: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0 > uhub0: 2 ports with 2 removable, self powered > ohci1: <OHCI (generic) USB controller> mem 0xfe8fd000-0xfe8fdfff irq 17 > at device 19.1 on pci0 > ohci1: [GIANT-LOCKED] > ohci1: [ITHREAD] > usb1: OHCI version 1.0, legacy support > usb1: SMM does not respond, resetting > usb1: <OHCI (generic) USB controller> on ohci1 > usb1: USB revision 1.0 > uhub1: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1 > uhub1: 2 ports with 2 removable, self powered > ohci2: <OHCI (generic) USB controller> mem 0xfe8fc000-0xfe8fcfff irq 18 > at device 19.2 on pci0 > ohci2: [GIANT-LOCKED] > ohci2: [ITHREAD] > usb2: OHCI version 1.0, legacy support > usb2: SMM does not respond, resetting > usb2: <OHCI (generic) USB controller> on ohci2 > usb2: USB revision 1.0 > uhub2: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2 > uhub2: 2 ports with 2 removable, self powered > ohci3: <OHCI (generic) USB controller> mem 0xfe8fb000-0xfe8fbfff irq 17 > at device 19.3 on pci0 > ohci3: [GIANT-LOCKED] > ohci3: [ITHREAD] > usb3: OHCI version 1.0, legacy support > usb3: SMM does not respond, resetting > usb3: <OHCI (generic) USB controller> on ohci3 > usb3: USB revision 1.0 > uhub3: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3 > uhub3: 2 ports with 2 removable, self powered > ohci4: <OHCI (generic) USB controller> mem 0xfe8fa000-0xfe8fafff irq 18 > at device 19.4 on pci0 > ohci4: [GIANT-LOCKED] > ohci4: [ITHREAD] > usb4: OHCI version 1.0, legacy support > usb4: SMM does not respond, resetting > usb4: <OHCI (generic) USB controller> on ohci4 > usb4: USB revision 1.0 > uhub4: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb4 > uhub4: 2 ports with 2 removable, self powered > ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfe8ff000-0xfe8ff0ff irq > 19 at device 19.5 on pci0 > ehci0: [GIANT-LOCKED] > ehci0: [ITHREAD] > usb5: EHCI version 1.0 > usb5: companion controllers, 2 ports each: usb0 usb1 usb2 usb3 usb4 > usb5: <EHCI (generic) USB 2.0 controller> on ehci0 > usb5: USB revision 2.0 > uhub5: <ATI EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb5 > uhub5: 10 ports with 10 removable, self powered > umass0: <Generic Mass Storage Device, class 0/0, rev 2.00/1.29, addr 2> > on uhub5 > pci0: <serial bus, SMBus> at device 20.0 (no driver attached) > atapci1: <ATI IXP600 UDMA133 controller> port > 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xff00-0xff0f at device 20.1 on pci0 > ata0: <ATA channel 0> on atapci1 > ata0: [ITHREAD] > hdac1: <ATI SB600 High Definition Audio Controller> mem > 0xfe8f4000-0xfe8f7fff irq 16 at device 20.2 on pci0 > hdac1: HDA Driver Revision: 20090329_0131 > hdac1: [ITHREAD] > isab0: <PCI-ISA bridge> at device 20.3 on pci0 > isa0: <ISA bus> on isab0 > pcib3: <ACPI PCI-PCI bridge> at device 20.4 on pci0 > pci3: <ACPI PCI bus> on pcib3 > pci3: <multimedia> at device 2.0 (no driver attached) > em0: <Intel(R) PRO/1000 Network Connection 6.9.6> port 0xe800-0xe83f mem > 0xfebc0000-0xfebdffff,0xfeba0000-0xfebbffff irq 21 at device 3.0 on pci3 > em0: [FILTER] > em0: Ethernet address: 00:1b:21:17:8f:61 > acpi_button0: <Power Button> on acpi0 > sio0: configured irq 4 not in bitmap of probed irqs 0 > sio0: port may not be enabled > sio0: configured irq 4 not in bitmap of probed irqs 0 > sio0: port may not be enabled > sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on > acpi0 > sio0: type 16550A > sio0: [FILTER] > cpu0: <ACPI CPU> on acpi0 > acpi_throttle0: <ACPI CPU Throttling> on cpu0 > acpi_throttle0: CLK_VAL field overlaps THT_EN bit > device_attach: acpi_throttle0 attach returned 6 > cpu1: <ACPI CPU> on acpi0 > cpu2: <ACPI CPU> on acpi0 > cpu3: <ACPI CPU> on acpi0 > orm0: <ISA Option ROMs> at iomem 0xc0000-0xcffff,0xd0000-0xd0fff on isa0 > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > kbd0 at atkbd0 > atkbd0: [GIANT-LOCKED] > atkbd0: [ITHREAD] > ppc0: cannot reserve I/O port range > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio1: configured irq 3 not in bitmap of probed irqs 0 > sio1: port may not be enabled > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > ukbd0: <Logitech USB Receiver, class 0/0, rev 1.10/38.10, addr 2> on uhub1 > kbd2 at ukbd0 > ums0: <Logitech USB Receiver, class 0/0, rev 1.10/38.10, addr 2> on uhub1 > ums0: 8 buttons and Z dir. > Timecounters tick every 1.000 msec > ipfw2 (+ipv6) initialized, divert loadable, nat loadable, rule-based > forwarding disabled, default to deny, logging unlimited > ad0: 38172MB <MAXTOR 6L040J2 A93.0500> at ata0-master UDMA133 > ad4: 715404MB <SAMSUNG HD753LJ 1AA01109> at ata2-master SATA300 > acd0: DVDR <Optiarc DVD RW AD-7203S/1.04> at ata3-master SATA150 > hdac0: HDA Codec #0: ATI R6xx HDMI > pcm0: <HDA ATI R6xx HDMI PCM #0 Digital> at cad 0 nid 1 on hdac0 > hdac1: HDA Codec #0: Realtek ALC888 > pcm1: <HDA Realtek ALC888 PCM #0 Analog> at cad 0 nid 1 on hdac1 > pcm2: <HDA Realtek ALC888 PCM #1 Analog> at cad 0 nid 1 on hdac1 > pcm3: <HDA Realtek ALC888 PCM #2 Digital> at cad 0 nid 1 on hdac1 > GEOM_LABEL: Label for provider ad0s1a is ufsid/4a76ae87acea749e. > GEOM_LABEL: Label for provider ad0s1d is ufsid/4a76ae9edced99b2. > GEOM_LABEL: Label for provider ad0s1e is ufsid/4a76ae9d2d7dce0a. > GEOM_LABEL: Label for provider ad0s1f is ufsid/4a76ae9d00089a00. > GEOM_LABEL: Label for provider ad4s1 is ntfs/XP_Pro_x64_UK. > GEOM_LABEL: Label for provider ad4s3 is ufsid/4a76ae871cba9765. > GEOM_LABEL: Label for provider ad4s5 is msdosfs/D0-P2. > (probe0:umass-sim0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 > (probe0:umass-sim0:0:0:0): CAM Status: SCSI Status Error > (probe0:umass-sim0:0:0:0): SCSI Status: Check Condition > (probe0:umass-sim0:0:0:0): NOT READY csi:0,aa,55,40 asc:3a,0 > (probe0:umass-sim0:0:0:0): Medium not present > (probe0:umass-sim0:0:0:0): Unretryable error > (probe1:ata2:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 > (probe1:ata2:0:0:0): CAM Status: SCSI Status Error > (probe1:ata2:0:0:0): SCSI Status: Check Condition > (probe1:ata2:0:0:0): NOT READY asc:3a,0 > (probe1:ata2:0:0:0): Medium not present > (probe1:ata2:0:0:0): Unretryable error > (probe0:umass-sim0:0:0:1): TEST UNIT READY. CDB: 0 20 0 0 0 0 > (probe0:umass-sim0:0:0:1): CAM Status: SCSI Status Error > (probe0:umass-sim0:0:0:1): SCSI Status: Check Condition > (probe0:umass-sim0:0:0:1): NOT READY csi:0,aa,55,40 asc:3a,0 > (probe0:umass-sim0:0:0:1): Medium not present > (probe0:umass-sim0:0:0:1): Unretryable error > (probe0:umass-sim0:0:0:2): TEST UNIT READY. CDB: 0 40 0 0 0 0 > (probe0:umass-sim0:0:0:2): CAM Status: SCSI Status Error > (probe0:umass-sim0:0:0:2): SCSI Status: Check Condition > (probe0:umass-sim0:0:0:2): NOT READY csi:0,aa,55,40 asc:3a,0 > (probe0:umass-sim0:0:0:2): Medium not present > (probe0:umass-sim0:0:0:2): Unretryable error > (probe0:umass-sim0:0:0:3): TEST UNIT READY. CDB: 0 60 0 0 0 0 > (probe0:umass-sim0:0:0:3): CAM Status: SCSI Status Error > (probe0:umass-sim0:0:0:3): SCSI Status: Check Condition > (probe0:umass-sim0:0:0:3): NOT READY csi:0,aa,55,40 asc:3a,0 > (probe0:umass-sim0:0:0:3): Medium not present > (probe0:umass-sim0:0:0:3): Unretryable error > SMP: AP CPU #1 Launched! > SMP: AP CPU #3 Launched! > SMP: AP CPU #2 Launched! > da0 at umass-sim0 bus 0 target 0 lun 0 > da0: <Generic USB SD Reader 1.00> Removable Direct Access SCSI-0 device > da0: 40.000MB/s transfers > da0: Attempt to query device size failed: NOT READY, Medium not present > cd0 at ata2 bus 0 target 0 lun 0 > cd0: <Optiarc DVD RW AD-7203S 1.04> Removable CD-ROM SCSI-0 device > cd0: 3.300MB/s transfers > cd0: Attempt to query device size failed: NOT READY, Medium not present > da1 at umass-sim0 bus 0 target 0 lun 1 > da1: <Generic USB CF Reader 1.01> Removable Direct Access SCSI-0 device > da1: 40.000MB/s transfers > da1: Attempt to query device size failed: NOT READY, Medium not present > da2 at umass-sim0 bus 0 target 0 lun 2 > da2: <Generic USB SM Reader 1.02> Removable Direct Access SCSI-0 device > da2: 40.000MB/s transfers > da2: Attempt to query device size failed: NOT READY, Medium not present > da3 at umass-sim0 bus 0 target 0 lun 3 > da3: <Generic USB MS Reader 1.03> Removable Direct Access SCSI-0 device > da3: 40.000MB/s transfers > da3: Attempt to query device size failed: NOT READY, Medium not present > Trying to mount root from ufs:/dev/ad0s1a > GEOM_LABEL: Label ufsid/4a76ae87acea749e removed. > GEOM_LABEL: Label for provider ad0s1a is ufsid/4a76ae87acea749e. > GEOM_LABEL: Label ufsid/4a76ae871cba9765 removed. > <11G8>/dev/ad4s3d: FILE SYSTEM CLEAN; SKIPPIENG CHECKS > OM_ > BEL: Label ufsid/4a76ae9d2d7dce0a removed. > GEOM_LABEL: Label for provider ad4s3 is ufsid/4a76ae871cba9765. > GEOM_LABEL: Label for provider ad0s1e is ufsid/4a76ae9d2d7dce0a. > GEOM_LABEL: Label ufsid/4a76ae9d00089a00 removed. > GEOM_LABEL: Label for provider ad0s1f is ufsid/4a76ae9d00089a00. > GEOM_LABEL: Label ufsid/4a76ae9edced99b2 removed. > GEOM_LABEL: Label for provider ad0s1d is ufsid/4a76ae9edced99b2. > GEOM_LABEL: Label ufsid/4a76ae87acea749e removed. > GEOM_LABEL: Label ufsid/4a76ae871cba9765 removed. > GEOM_LABEL: Label ufsid/4a76ae9d2d7dce0a removed. > GEOM_LABEL: Label ufsid/4a76ae9d00089a00 removed. > GEOM_LABEL: Label ufsid/4a76ae9edced99b2 removed. > netsmb_dev: loaded > drm0: <ATI Radeon HD 2600 Pro> on vgapci0 > vgapci0: child drm0 requested pci_enable_busmaster > info: [drm] Initialized radeon 1.29.0 20080528 > info: [drm] Setting GART location based on new memory map > info: [drm] Loading RV630 CP Microcode > info: [drm] Loading RV630 PFP Microcode > info: [drm] Resetting GPU > info: [drm] writeback test succeeded in 1 usecs > drm0: [ITHREAD] > > $ camcontrol devlist > <Generic USB SD Reader 1.00> at scbus0 target 0 lun 0 (pass0,da0) > <Generic USB CF Reader 1.01> at scbus0 target 0 lun 1 (pass1,da1) > <Generic USB SM Reader 1.02> at scbus0 target 0 lun 2 (pass2,da2) > <Generic USB MS Reader 1.03> at scbus0 target 0 lun 3 (pass3,da3) > <Optiarc DVD RW AD-7203S 1.04> at scbus3 target 0 lun 0 (pass4,cd0) > $ > > $ cat /etc/devfs.conf | grep perm > perm acd0 0666 > perm cd0 0666 > perm xpt0 0666 > perm pass0 0666 > perm pass1 0666 > perm pass2 0666 > perm pass4 0666 > $ > > $ cat /boot/loader.conf > snd_hda_load="YES" > sem_load="YES" > hw.ata.atapi_dma=1 > $ > > hal daemon and dbus daemon are both running. > > Does anyone have an idea what the problem might be, and if there is a > solution to it ? > > Thanks, > > Rick > _______________________________________________ > freebsd-multimedia@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-multimedia > To unsubscribe, send any mail to > "freebsd-multimedia-unsubscribe@freebsd.org"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?4A82B20C.6030703>