Date: Fri, 01 Dec 2000 16:51:55 -0800 From: Philippe Le Berre <philippe@le-berre.com> To: hardware@freebsd.org Subject: Trouble with IBM UltraStar 18GB Message-ID: <5.0.1.4.0.20001201163731.0191feb0@puccini.grenoble.hp.com>
next in thread | raw e-mail | index | archive | help
Hi, I have a brand new system, the mother board is a Tyan Thunder LE S2510 with 1 GB of RAM and a 18 GB UltraStar (IBM DDYS-T18350N S93E). I have no trouble installing FreeBSD 4.1.1 release on it, but once I have cvsupped stable and try to run make buildworld it quickly fails with a 'error in wait: -1' at different points. If I set all the volumes with the sync option, then the buildworld goes close to the end but fails also with either a 'gcc execute error' or 'error in wait: -1'. Thinking of a bad luck with a firmware I have switched the 18GB with another one (exact same kind) and change the cables, but that doesn't help ... I am stucked! Is there known issues with those drives? The mother board is certified by Tyan with FreeBSD 4.1, so I would not think of issues with it, am I wrong? I need to try with the UDMA66 drive I have plugged (Maxtor) into as soon as possible, but all advices, experiences and opinions are welcomed. I would really like to be able to use those UltraStars & SCSI-3! thanks, -philippe ------------->> dmesg -------->>>------------------- Copyright (c) 1992-2000 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.1.1-RELEASE #0: Tue Sep 26 00:46:59 GMT 2000 jkh@narf.osd.bsdi.com:/usr/src/sys/compile/GENERIC Timecounter "i8254" frequency 1193182 Hz CPU: Pentium III/Pentium III Xeon/Celeron (797.48-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x686 Stepping = 6 Features=0x387fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,PN,MMX,FXSR ,XMM> real memory = 1073741824 (1048576K bytes) avail memory = 1041694720 (1017280K bytes) Preloaded elf kernel "kernel" at 0xc0416000. Pentium Pro MTRR support enabled md0: Malloc disk npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <RCC LE host to PCI bridge> on motherboard pci0: <PCI bus> on pcib0 pci0: <ATI Mach64-GR graphics accelerator> at 1.0 irq 11 fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xd400-0xd43f mem 0xfe900000-0xfe9fffff,0xfeafe000-0xfeafef ff irq 9 at device 4.0 on pci0 fxp0: Ethernet address 00:e0:81:01:3f:51 fxp1: <Intel Pro 10/100B/100+ Ethernet> port 0xd000-0xd03f mem 0xfe700000-0xfe7fffff,0xfeafd000-0xfeafdf ff irq 5 at device 5.0 on pci0 fxp1: Ethernet address 00:e0:81:01:3f:52 isab0: <PCI to ISA bridge (vendor=1166 device=0200)> at device 15.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Generic PCI ATA controller> port 0xffa0-0xffaf at device 15.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 ohci0: <OHCI (generic) USB controller> mem 0xfeafc000-0xfeafcfff irq 10 at device 15.2 on pci0 usb0: OHCI version 1.0, legacy support usb0: <OHCI (generic) USB controller> on ohci0 usb0: USB revision 1.0 uhub0: (unknown) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 4 ports with 4 removable, self powered pcib1: <RCC LE host to PCI bridge> on motherboard pci1: <PCI bus> on pcib1 sym0: <1010-33> port 0xe400-0xe4ff mem 0xfebd8000-0xfebd9fff,0xfebe0000-0xfebe03ff irq 7 at device 6.0 o n pci1 sym0: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking sym0: open drain IRQ line driver, using on-chip SRAM sym0: using LOAD/STORE-based firmware. sym0: handling phase mismatch from SCRIPTS. sym1: <1010-33> port 0xe800-0xe8ff mem 0xfebf0000-0xfebf1fff,0xfebf8000-0xfebf83ff irq 10 at device 6.1 on pci1 sym1: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking sym1: open drain IRQ line driver, using on-chip SRAM sym1: using LOAD/STORE-based firmware. sym1: handling phase mismatch from SCRIPTS. fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model IntelliMouse, device ID 3 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A ppc0: parallel port not found. ad0: 14655MB <Maxtor 51536H2> [29777/16/63] at ata0-master using BIOSDMA acd0: CDROM <MATSHITA CR-175> at ata1-slave using PIO4 Waiting 15 seconds for SCSI devices to settle (noperiph:sym0:0:-1:-1): SCSI BUS reset delivered. (noperiph:sym1:0:-1:-1): SCSI BUS reset delivered. Mounting root from ufs:/dev/da0s1a da0 at sym0 bus 0 target 1 lun 0 da0: <IBM DDYS-T18350N S93E> Fixed Direct Access SCSI-3 device da0: 160.000MB/s transfers (80.000MHz, offset 62, 16bit), Tagged Queueing Enabled da0: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C) To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-hardware" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?5.0.1.4.0.20001201163731.0191feb0>