Date: Sat, 02 Mar 2013 09:54:02 -0600 From: Krzysztof Parzyszek <kristof@swissmail.org> To: freebsd-usb@FreeBSD.org Subject: Re: Failed to read CSW: USB_ERR_STALLED Message-ID: <5132209A.3020401@swissmail.org> In-Reply-To: <51321D3E.2040600@swissmail.org> References: <51321D3E.2040600@swissmail.org>
next in thread | previous in thread | raw e-mail | index | archive | help
Here's the beginning of dmesg:
Copyright (c) 1992-2013 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 9.1-STABLE #6 r247608: Fri Mar 1 21:27:49 CST 2013
root@apple5:/usr/obj/usr/src/sys/APPLE5 powerpc
cpu0: IBM PowerPC 970MP revision 1.1, 2500.32 MHz
cpu0: Features dc000000<PPC32,PPC64,ALTIVEC,FPU,MMU>
cpu0: HID0 1511081<DEEPNAP,NAP,DPM,NHR,TBEN,ENATTN>
real memory = 17159626752 (16364 MB)
avail memory = 16319057920 (15563 MB)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
cpu0: dev=ff89d680 (BSP)
cpu1: dev=ff89eb70
cpu2: dev=ff89f248
cpu3: dev=ff89f920
kbd0 at kbdmux0
nexus0: <Open Firmware Nexus device>
cpulist0: <Open Firmware CPU Group> on nexus0
cpu0: <Open Firmware CPU> on cpulist0
pcr0: <PPC 970 Power Control Register> on cpu0
cpu1: <Open Firmware CPU> on cpulist0
pcr1: <PPC 970 Power Control Register> on cpu1
cpu2: <Open Firmware CPU> on cpulist0
pcr2: <PPC 970 Power Control Register> on cpu2
cpu3: <Open Firmware CPU> on cpulist0
pcr3: <PPC 970 Power Control Register> on cpu3
powermac_nvram0: <Apple NVRAM> on nexus0
powermac_nvram0: bank0 generation 736, bank1 generation 737
unin0: <Apple UniNorth System Controller> on nexus0
unin0: Version 66
iichb0: <Keywest I2C controller> mem 0xf8001000-0xf8001fff irq 0 on unin0
iicbus0: <OFW I2C bus> on iichb0
iicbus0: <unknown card> at addr 0x94
iicbus0: <unknown card> at addr 0x96
iicbus0: <unknown card> at addr 0x98
iicbus0: <unknown card> at addr 0x9c
htpic0: <OpenPIC Interrupt Controller> mem 0xf8040000-0xf807ffff on unin0
pcib0: <IBM CPC945 PCI Express Root> on nexus0
pci0: <OFW PCI bus> on pcib0
pcib1: <IBM CPC9X5 HyperTransport Tunnel> on nexus0
pcib1: 86 HT IRQs on device 7.0
pci1: <OFW PCI bus> on pcib1
pcib1: Enabling MSI window for HyperTransport slave at pci1:0:1:0
pcib2: <OFW PCI-PCI bridge> at device 1.0 on pci1
pci2: <OFW PCI bus> on pcib2
pcib3: <OFW PCI-PCI bridge> at device 2.0 on pci1
pci3: <OFW PCI bus> on pcib3
bge0: <Broadcom BCM5714 B3, ASIC rev. 0x008003> mem
0xfa530000-0xfa53ffff,0xfa520000-0xfa52ffff irq 66 at device 4.0 on pci3
bge0: CHIP ID 0x00008003; ASIC REV 0x08; CHIP REV 0x80; PCI-X 33 MHz
miibus0: <MII bus> on bge0
brgphy0: <BCM5780 1000BASE-T media interface> PHY 1 on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bge0: Ethernet address: 00:16:cb:37:e2:e0
bge1: <Broadcom BCM5714 B3, ASIC rev. 0x008003> mem
0xfa510000-0xfa51ffff,0xfa500000-0xfa50ffff irq 67 at device 4.1 on pci3
bge1: CHIP ID 0x00008003; ASIC REV 0x08; CHIP REV 0x80; PCI-X 33 MHz
miibus1: <MII bus> on bge1
brgphy1: <BCM5780 1000BASE-T media interface> PHY 1 on miibus1
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bge1: Ethernet address: 00:16:cb:37:e2:e1
pcib4: <OFW PCI-PCI bridge> at device 3.0 on pci1
pci4: <OFW PCI bus> on pcib4
pcib5: <OFW PCI-PCI bridge> at device 4.0 on pci1
pci5: <OFW PCI bus> on pcib5
pcib6: <OFW PCI-PCI bridge> at device 5.0 on pci1
pci6: <OFW PCI bus> on pcib6
vgapci0: <VGA-compatible display> mem
0x82000000-0x82ffffff,0x88000000-0x8fffffff,0x81000000-0x81ffffff irq 63
at device 0.0 on pci6
pcib7: <OFW PCI-PCI bridge> at device 6.0 on pci1
pci7: <OFW PCI bus> on pcib7
pcib8: <OFW PCI-PCI bridge> at device 7.0 on pci1
pci8: <OFW PCI bus> on pcib8
gem0: <Apple Shasta GMAC Ethernet> mem 0xfa200000-0xfa3fffff at device
15.0 on pci8
gem0: failed to allocate resources
device_attach: gem0 attach returned 6
pcib9: <OFW PCI-PCI bridge> at device 8.0 on pci1
pci9: <OFW PCI bus> on pcib9
macio0: <Shasta I/O Controller> mem 0x80000000-0x8007ffff at device 7.0
on pci9
macgpio0: <MacIO GPIO Controller> mem 0x50-0x8a on macio0
scc0: <Zilog Z8530 dual channel SCC> mem
0x13000-0x13fff,0x8400-0x84ff,0x8500-0x85ff,0x8600-0x86ff,0x8700-0x87ff
irq 23,17,18,24,19,20 on macio0
uart0: <z8530, channel A> on scc0
uart1: <z8530, channel B> on scc0
iichb1: <Keywest I2C controller> mem 0x18000-0x18fff irq 27 on macio0
iicbus1: <OFW I2C bus> on iichb1
iicbus1: <unknown card> at addr 0x8c
iicbus1: <unknown card> at addr 0x24
ohci0: <NEC uPD 9210 USB controller> mem 0x80082000-0x80082fff irq 70 at
device 11.0 on pci9
usbus0 on ohci0
ohci1: <NEC uPD 9210 USB controller> mem 0x80081000-0x80081fff irq 70 at
device 11.1 on pci9
usbus1 on ohci1
ehci0: <NEC uPD 720100 USB 2.0 controller> mem 0x80080000-0x800800ff irq
70 at device 11.2 on pci9
usbus2: EHCI version 1.0
usbus2 on ehci0
pcib10: <OFW PCI-PCI bridge> at device 9.0 on pci1
pci10: <OFW PCI bus> on pcib10
atapci0: <ServerWorks K2 SATA150 controller> mem 0xfa402000-0xfa403fff
irq 10 at device 12.0 on pci10
pcib1: failed to reserve resource for pcib10
atapci0: 0x10 bytes of rid 0x20 res 4 failed (0, 0xffffffffffffffff).
ata2: <ATA channel> at channel 0 on atapci0
ata3: <ATA channel> at channel 1 on atapci0
ata4: <ATA channel> at channel 2 on atapci0
ata5: <ATA channel> at channel 3 on atapci0
ata0: <Shasta Kauai ATA Controller> mem 0xfa404000-0xfa407fff irq 38 at
device 13.0 on pci10
pci10: <serial bus, FireWire> at device 14.0 (no driver attached)
smu0: <Apple System Management Unit> on nexus0
iichb2: <SMU I2C controller> on smu0
iicbus2: <OFW I2C bus> on iichb2
smusat0: <SMU Satellite Sensors> at addr 0xb0 on iicbus2
smusat1: <SMU Satellite Sensors> at addr 0xb2 on iicbus2
iicbus2: <unknown card> at addr 0xd4
iichb3: <SMU I2C controller> on smu0
iicbus3: <OFW I2C bus> on iichb3
sc0: <System console> on nexus0
sc0: Unknown <16 virtual consoles, flags=0x300>
Timecounter "timebase" frequency 33333333 Hz quality 0
Event timer "decrementer" frequency 33333333 Hz quality 1000
Timecounters tick every 1.000 msec
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
ugen0.1: <NEC> at usbus0
uhub0: <NEC OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <NEC> at usbus1
uhub1: <NEC OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
usbus2: 480Mbps High Speed USB v2.0
ugen2.1: <NEC> at usbus2
uhub2: <NEC EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
uhub1: 2 ports with 2 removable, self powered
uhub0: 3 ports with 3 removable, self powered
uhub2: 5 ports with 5 removable, self powered
ada0 at ata2 bus 0 scbus0 target 0 lun 0
ada0: <ST3250620NS 3.AEG> ATA-7 SATA 1.x device
ada0: 150.000MB/s transfers (SATA 1.x, UDMA5, PIO 8192bytes)
ada0: 238475MB (488397168 512 byte sectors: 16H 63S/T 16383C)
ada0: Previously was known as ad0cd0 at ata0 bus 0 scbus4 target 0 lun 0
cd0: <HL-DT-ST DVD-RW GWA-4165B C006> Removable CD-ROM SCSI-0 device
cd0: 66.700MB/s transfers (UDMA4, ATAPI 12bytes, PIO 65534bytes)
cd0: Attempt to query device size failed: NOT READY, Medium not present
SMP: AP CPU #3 launched
SMP: AP CPU #1 launched
SMP: AP CPU #2 launched
Swap zone entries reduced from 1995943 to 1330628.
Root mount waiting for: usbus2
Trying to mount root from ufs:/dev/ada0s3 [rw]...
ugen0.2: <Chicony> at usbus0
interruptskbd1 at ukbd0
ethernet point_to_pointuhid0: <Chicony Wireless Device, class 0/0, rev
2.00/1.31, addr 2> on usbus0
ums0: <Chicony Wireless Device, class 0/0, rev 2.00/1.31, addr 2> on usbus0
ums0: 3 buttons and [XYZ] coordinates ID=0
kickstart.
ugen2.2: <JMicron> at usbus2
umass0: <MSC Bulk-Only Transfer> on usbus2
umass0: SCSI over Bulk-Only; quirks = 0x0000
umass0:umass_cam_action: 5:-1:-1:XPT_PATH_INQ:.
umuamsass0s:05::u0m:a-s1s:_ cAatmt_aacchteido nt:o 5s:c-b1u:s-51:X
PuTm_aPsAsT0H:_uImNaQs:s._at
taucmha:s sA0t:tuamcahs sf_icnaims_haectdio
n: 5:0:0:XPT_PATH_INQ:.
umass0:umass_cam_action: 5:0:0:XPT_PATH_INQ:.
umass0:umass_cam_action: 5:0:0:XPT_GET_TRAN_SETTINGS:.
umass0:umass_cam_action: 5:0:0:XPT_SET_TRAN_SETTINGS:.
umass0:umass_cam_action: 5:0:0:XPT_PATH_INQ:.
umass0:umass_cam_action: 5:0:0:XPT_PATH_INQ:.
umass0:umass_cam_action: 5:0:0:XPT_SCSI_IO: cmd: 0x12, flags: 0x40, 6b
cmd/36b data/18b sense
umass0:umass_bbb_dump_cbw: CBW 1: cmd = 6b (0x120000002400), data = 36b,
lun = 0, dir = in
umass0:umass_transfer_start: transfer index = 4
umass0:umass_t_bbb_data_read_callback: max_bulk=131072, data_rem=36
umass0:umass_t_bbb_data_read_callback: max_bulk=131072, data_rem=0
umass0:umass_transfer_start: transfer index = 8
umass0:umass_bbb_dump_csw: CSW 1: sig = 0x53425355 (valid), tag =
0x00000001, res = 0, status = 0x00 (good)
umass0:umass_cam_action: 5:0:0:XPT_PATH_INQ:.
umass0:umass_cam_action: 5:0:0:XPT_PATH_INQ:.
umass0:umass_cam_action: 5:0:0:XPT_GET_TRAN_SETTINGS:.
umass0:umass_cam_action: 5:0:0:XPT_SET_TRAN_SETTINGS:.
umass0:umass_cam_action: 5:0:0:XPT_SCSI_IO: cmd: 0x12, flags: 0x40, 6b
cmd/255b data/18b sense
umass0:umass_bbb_dump_cbw: CBW 2: cmd = 6b (0x12010000ff00), data =
255b, lun = 0, dir = in
umass0:umass_transfer_start: transfer index = 4
umass0:umass_t_bbb_data_read_callback: max_bulk=131072, data_rem=255
umass0:umass_t_bbb_data_read_callback: max_bulk=131072, data_rem=0
umass0:umass_transfer_start: transfer index = 8
umass0:umass_t_bbb_status_callback: Failed to read CSW: USB_ERR_STALLED,
try 0
umass0:umass_transfer_start: transfer index = 5
umass0:umass_transfer_start: transfer index = 8
umass0:umass_bbb_dump_csw: CSW 2: sig = 0x53425355 (valid), tag =
0x00000002, res = 215, status = 0x00 (good)
[...]
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?5132209A.3020401>