Date: 23 May 2001 18:02:52 +0200 From: Juan Jose Garcia Ripoll <jjgarcia@ind-cr.uclm.es> To: freebsd-stable@FreeBSD.ORG Subject: SMP lockups with 4.3 Message-ID: <87k838njdf.fsf@mobile-ripoll.arrakis.es>
next in thread | raw e-mail | index | archive | help
--Multipart_Wed_May_23_18:02:52_2001-1 Content-Type: text/plain; charset=US-ASCII Hi, I have upgraded two machines from 4.2 to 4.3 using cvsup. The first one is the laptop I am writing on, and it works ok; the second one is a dual PIII/700 with a MS motherbard. It is this second machine the one which experiences lockups with a 4.3 SMP kernel as cvsuped last week. Booting with a single processor 4.2 kernel solves the problem. The machine is almost bare bones, with apache and qpopper, and since everything works with 4.2 I suspect the problem is related to a change in the SMP kernel. As a side note, the same machine worked ok with Debian using a SMP linux kernel. I just replaced it with FreeBSD because I find the latter easier to maintain. The output of dmesg with the 4.2 is below, together with one of the 4.3 kernels I have tried. What do you think I should do now? TIA Juanjo --Multipart_Wed_May_23_18:02:52_2001-1 Content-Type: text/plain; charset=US-ASCII Content-Disposition: inline; filename="DMESG.TXT" Content-Transfer-Encoding: quoted-printable Copyright (c) 1992-2000 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.2-RELEASE #0: Mon Nov 20 13:02:55 GMT 2000 jkh@bento.FreeBSD.org:/usr/src/sys/compile/GENERIC Timecounter "i8254" frequency 1193182 Hz CPU: Pentium III/Pentium III Xeon/Celeron (735.00-MHz 686-class CPU) Origin =3D "GenuineIntel" Id =3D 0x686 Stepping =3D 6 Features=3D0x387fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE= ,MCA,CMOV,PAT,PSE36,PN,MMX,FXSR,SSE> real memory =3D 134152192 (131008K bytes) avail memory =3D 126328832 (123368K bytes) Preloaded elf kernel "kernel.old" at 0xc0436000. Pentium Pro MTRR support enabled md0: Malloc disk npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <Host to PCI bridge> on motherboard pci0: <PCI bus> on pcib0 pcib2: <VIA 82C598MVP (Apollo MVP3) PCI-PCI (AGP) bridge> at device 1.0 on = pci0 pci1: <PCI bus> on pcib2 pci1: <S3 Savage 4 graphics accelerator> at 0.0 irq 12 isab0: <VIA 82C686 PCI-ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <VIA 82C686 ATA66 controller> port 0x9000-0x900f at device 7.1 on = pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 uhci0: <VIA 83C572 USB controller> port 0x9400-0x941f irq 9 at device 7.2 o= n pci0 usb0: <VIA 83C572 USB controller> on uhci0 usb0: USB revision 1.0 uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: <VIA 83C572 USB controller> port 0x9800-0x981f irq 9 at device 7.3 o= n pci0 usb1: <VIA 83C572 USB controller> on uhci1 usb1: USB revision 1.0 uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered chip2: <VIA 82C686 AC97 Audio> port 0xa400-0xa403,0xa000-0xa003,0x9c00-0x9c= ff irq 11 at device 7.5 on pci0 atapci1: <Promise ATA100 controller> port 0xbc00-0xbc3f,0xb800-0xb803,0xb40= 0-0xb407,0xb000-0xb003,0xac00-0xac07 mem 0xdf100000-0xdf11ffff irq 11 at de= vice 12.0 on pci0 ata2: at 0xac00 on atapci1 ata3: at 0xb400 on atapci1 fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xc000-0xc03f mem 0xdf000000-0= xdf0fffff,0xdf120000-0xdf120fff irq 10 at device 18.0 on pci0 fxp0: Ethernet address 00:d0:b7:c8:68:07 pcib1: <Host to PCI bridge> on motherboard pci2: <PCI bus> on pcib1 fdc0: direction bit not set fdc0: cmd 3 failed at out byte 1 of 3 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=3D0x300> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A ppc0: <Parallel port> at port 0x278-0x27f irq 7 on isa0 ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 ad0: 6204MB <ST36531A> [13446/15/63] at ata0-master UDMA33 ata1-master: DMA limited to UDMA33, non-ATA66 compliant cable ad2: 8223MB <ST38410A> [16708/16/63] at ata1-master UDMA33 afd0: 239MB <IOMEGA ZIP 250 ATAPI> [239/64/32] at ata0-slave using PIO3 acd0: CD-RW <10X8X32> at ata1-slave using PIO4 Mounting root from ufs:/dev/ad0s1a WARNING: / was not properly dismounted --Multipart_Wed_May_23_18:02:52_2001-1 Content-Type: application/octet-stream Content-Disposition: attachment; filename="KERNEL.CFG" Content-Transfer-Encoding: quoted-printable # # GENERIC -- Generic kernel configuration file for FreeBSD/i386 # # For more information on this file, please read the handbook section on # Kernel Configuration Files: # # http://www.FreeBSD.org/handbook/kernelconfig-config.html # # The handbook is also available locally in /usr/share/doc/handbook # if you've installed the doc distribution, otherwise always see the # FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the # latest information. # # An exhaustive list of options and more detailed explanations of the # device lines is also present in the ./LINT configuration file. If you are # in doubt as to the purpose or necessity of a line, check first in LINT. # # $FreeBSD: src/sys/i386/conf/GENERIC,v 1.246.2.25 2001/05/13 03:50:01 jlem= on Exp $ machine i386 #cpu I386_CPU #cpu I486_CPU #cpu I586_CPU cpu I686_CPU ident GENERIC maxusers 32 #makeoptions DEBUG=3D-g #Build kernel with gdb(1) debug symbols #options MATH_EMULATE #Support for x87 emulation options INET #InterNETworking options INET6 #IPv6 communications protocols options FFS #Berkeley Fast Filesystem options FFS_ROOT #FFS usable as root device [keep this!] options SOFTUPDATES #Enable FFS soft updates support #options MFS #Memory Filesystem #options MD_ROOT #MD is a potential root device options NFS #Network Filesystem #options NFS_ROOT #NFS usable as root device, NFS required options MSDOSFS #MSDOS Filesystem options CD9660 #ISO 9660 Filesystem #options CD9660_ROOT #CD-ROM usable as root, CD9660 required options PROCFS #Process filesystem options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!] options SCSI_DELAY=3D15000 #Delay (in ms) before probing SCSI options UCONSOLE #Allow users to grab the console options USERCONFIG #boot -c editor #options VISUAL_USERCONFIG #visual boot -c editor options KTRACE #ktrace(1) support options SYSVSHM #SYSV-style shared memory options SYSVMSG #SYSV-style message queues options SYSVSEM #SYSV-style semaphores options P1003_1B #Posix P1003_1B real-time extensions options _KPOSIX_PRIORITY_SCHEDULING options ICMP_BANDLIM #Rate limit bad replies options KBD_INSTALL_CDEV # install a CDEV entry in /dev # To make an SMP kernel, the next two are needed options SMP # Symmetric MultiProcessor Kernel options APIC_IO # Symmetric (APIC) I/O device isa #device eisa device pci # Floppy drives device fdc0 at isa? port IO_FD1 irq 6 drq 2 device fd0 at fdc0 drive 0 device fd1 at fdc0 drive 1 # ATA and ATAPI devices device ata0 at isa? port IO_WD1 irq 14 device ata1 at isa? port IO_WD2 irq 15 device ata device atadisk # ATA disk drives device atapicd # ATAPI CDROM drives device atapifd # ATAPI floppy drives #device atapist # ATAPI tape drives options ATA_STATIC_ID #Static device numbering # SCSI Controllers #device ahb # EISA AHA1742 family #device ahc # AHA2940 and onboard AIC7xxx devices #device amd # AMD 53C974 (Tekram DC-390(T)) #device isp # Qlogic family #device ncr # NCR/Symbios Logic #device sym # NCR/Symbios Logic (newer chipsets) #options SYM_SETUP_LP_PROBE_MAP=3D0x40 # Allow ncr to attach legacy NCR devices when=20 # both sym and ncr are configured #device adv0 at isa? #device adw #device bt0 at isa? #device aha0 at isa? #device aic0 at isa? #device ncv # NCR 53C500 #device nsp # Workbit Ninja SCSI-3 #device stg # TMC 18C30/18C50 # SCSI peripherals device scbus # SCSI bus (required) device da # Direct Access (disks) device sa # Sequential Access (tape etc) device cd # CD device pass # Passthrough device (direct SCSI access) # RAID controllers interfaced to the SCSI subsystem #device asr # DPT SmartRAID V, VI and Adaptec SCSI RAID #device dpt # DPT Smartcache - See LINT for options! #device mly # Mylex AcceleRAID/eXtremeRAID # RAID controllers #device aac # Adaptec FSA RAID, Dell PERC2/PERC3 #device ida # Compaq Smart RAID #device amr # AMI MegaRAID #device mlx # Mylex DAC960 family #device twe # 3ware Escalade # atkbdc0 controls both the keyboard and the PS/2 mouse device atkbdc0 at isa? port IO_KBD device atkbd0 at atkbdc? irq 1 flags 0x1 device psm0 at atkbdc? irq 12 device vga0 at isa? # splash screen/screen saver pseudo-device splash # syscons is the default console driver, resembling an SCO console device sc0 at isa? flags 0x100 # Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver #device vt0 at isa? #options XSERVER # support for X server on a vt console #options FAT_CURSOR # start with block cursor # If you have a ThinkPAD, uncomment this along with the rest of the PCVT li= nes #options PCVT_SCANSET=3D2 # IBM keyboards are non-std # Floating point support - do not disable. device npx0 at nexus? port IO_NPX irq 13 # Power management support (see LINT for more options) device apm0 at nexus? disable flags 0x20 # Advanced Power Management # PCCARD (PCMCIA) support #device card #device pcic0 at isa? irq 0 port 0x3e0 iomem 0xd0000 #device pcic1 at isa? irq 0 port 0x3e2 iomem 0xd4000 disable # Serial (COM) ports device sio0 at isa? port IO_COM1 flags 0x10 irq 4 device sio1 at isa? port IO_COM2 irq 3 device sio2 at isa? disable port IO_COM3 irq 5 device sio3 at isa? disable port IO_COM4 irq 9 # Parallel port device ppc0 at isa? irq 7 device ppbus # Parallel port bus (required) device lpt # Printer device plip # TCP/IP over parallel #device ppi # Parallel port interface device #device vpo # Requires scbus and da # PCI Ethernet NICs. device de # DEC/Intel DC21x4x (``Tulip'') device tx # SMC 9432TX (83c170 ``EPIC'') device vx # 3Com 3c590, 3c595 (``Vortex'') device wx # Intel Gigabit Ethernet Card (``Wiseman'') # PCI Ethernet NICs that use the common MII bus controller code. # NOTE: Be sure to keep the 'device miibus' line in order to use these NICs! device miibus # MII bus support device dc # DEC/Intel 21143 and various workalikes device fxp # Intel EtherExpress PRO/100B (82557, 82558) device pcn # AMD Am79C79x PCI 10/100 NICs device rl # RealTek 8129/8139 device sf # Adaptec AIC-6915 (``Starfire'') device sis # Silicon Integrated Systems SiS 900/SiS 7016 device ste # Sundance ST201 (D-Link DFE-550TX) device tl # Texas Instruments ThunderLAN device vr # VIA Rhine, Rhine II device wb # Winbond W89C840F device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'') # ISA Ethernet NICs. device ed0 at isa? port 0x280 irq 10 iomem 0xd8000 device ex device ep device fe0 at isa? port 0x300 # Xircom Ethernet device xe # PRISM I IEEE 802.11b wireless NIC. device awi # WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really # exists only as a PCMCIA device, so there is no ISA attachment needed # and resources will always be dynamically assigned by the pccard code. device wi # Aironet 4500/4800 802.11 wireless NICs. Note: the declaration below will # work for PCMCIA and PCI cards, as well as ISA cards set to ISA PnP # mode (the factory default). If you set the switches on your ISA # card for a manually chosen I/O address and IRQ, you must specify # those parameters here. device an # The probe order of these is presently determined by i386/isa/isa_compat.c. device ie0 at isa? port 0x300 irq 10 iomem 0xd0000 #device le0 at isa? port 0x300 irq 5 iomem 0xd0000 device lnc0 at isa? port 0x280 irq 10 drq 0 device cs0 at isa? port 0x300 device sn0 at isa? port 0x300 irq 10 # Pseudo devices - the number indicates how many units to allocate. pseudo-device loop # Network loopback pseudo-device ether # Ethernet support #pseudo-device sl 1 # Kernel SLIP pseudo-device ppp 1 # Kernel PPP pseudo-device tun # Packet tunnel. pseudo-device pty # Pseudo-ttys (telnet etc) #pseudo-device md # Memory "disks" pseudo-device gif 4 # IPv6 and IPv4 tunneling pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation) # The `bpf' pseudo-device enables the Berkeley Packet Filter. # Be aware of the administrative consequences of enabling this! #pseudo-device bpf #Berkeley packet filter # USB support #device uhci # UHCI PCI->USB interface #device ohci # OHCI PCI->USB interface #device usb # USB Bus (required) #device ugen # Generic #device uhid # "Human Interface Devices" #device ukbd # Keyboard #device ulpt # Printer #device umass # Disks/Mass storage - Requires scbus and da #device ums # Mouse #device uscanner # Scanners # USB Ethernet, requires mii #device aue # ADMtek USB ethernet #device cue # CATC USB ethernet #device kue # Kawasaki LSI USB ethernet --Multipart_Wed_May_23_18:02:52_2001-1-- To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?87k838njdf.fsf>