Date: Sat, 7 Nov 2009 16:57:59 +0100 From: Sven Hazejager <sven@hazejager.nl> To: freebsd-embedded@freebsd.org Subject: Re: Problem booting nanoBSD 7.2-p4 on Alix Message-ID: <8ffccde70911070757y73b0b6f8m883394672199b5bc@mail.gmail.com> In-Reply-To: <20091107124411.GA5551@webgroup.ch> References: <8ffccde70911061200t6788ca9bo67a094122f18b6ab@mail.gmail.com> <20091107124411.GA5551@webgroup.ch>
next in thread | previous in thread | raw e-mail | index | archive | help
On Fri, Nov 06, 2009 at 09:00:08PM +0100, Sven Hazejager wrote:
> I'm having some challenging issues booting nanoBSD 7.2-p4 on CF on an
> Alix serial-only system.
Thanks Mike and Adrian for their suggestions, but no luck yet. I do
not have atkbd or atkbdc in my kernel. Remember: this kernel boots
fine over PXE :-/
This is the output that I see after going into the loader and typing
"lsdev", "show" and finally "boot". The jibberish halfway is boot0
that runs at 9600 baud. I also see a "bad bsdlabel" for the cfg slice
when I run this image in a VM; it doesn't seem to be a problem there.
Any suggestions? I will keep trying all the "-o nopacket" vs. CHS/LBA
in tinybios vs. 16/63 or 32/63 heads/sectors set in nanoBSD
combinations... But the kernel loads fine!!
PC Engines ALIX.2 v0.99h
640 KB Base Memory
261120 KB Extended Memory
01F0 Master 848A SAMSUNG CF/ATA
Phys C/H/S 2025/16/63 Log C/H/S 1012/32/63
Intel UNDI, PXE-2.0 (build 082)
Copyright (C) 1997,1998,1999 Intel Corporation
VIA Rhine III Management Adapter v2.43 (2005/12/15)
PXE-E61: Media test failure, check cable
PXE-M0F: Exiting Intel PXE ROM.
=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=
=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=E0=
=E0=E0=E0=E0=E0=E0=E8I=D6=EB=B9=BD=B9=A5
BIOS
drive C: is disk0
BIOS 640kB/261120kB available memory
FreeBSD/i386 bootstrap loader, Revision 1.1
(root@aldebaran.chain.loc, Sat Nov 7 16:58:22 CET 2009)
> \
\: unknown command
-
/boot/kernel/kernel text=3D0x3824a0 data=3D0x42760+0x2a29c
syms=3D[0x4+0x42700+0x4+0x567d4]
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel] in 5 seconds...
Type '?' for a list of commands, 'help' for more detailed help.
OK lsdev
cd devices:
disk devices:
disk0: BIOS drive C:
disk0s1a: FFS
disk0s3: FFS bad disklabel
pxe devices:
OK show
LINES=3D24
boot_serial=3DYES
comconsole_speed=3D57600
console=3Dcomconsole
currdev=3Ddisk0s1a:
interpret=3DOK
kernelname=3D/boot/kernel/kernel
loaddev=3Ddisk0s1a:
prompt=3D${interpret}
OK boot
\ <-- STUCK!
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?8ffccde70911070757y73b0b6f8m883394672199b5bc>