Date: Thu, 12 Apr 2001 00:59:46 -0700 From: Forrest <praxis@techpraxis.com> To: FreeBSD Questions <freebsd-questions@freebsd.org> Subject: Please help: -- sis0 : watchdog timeout? Message-ID: <B6FAAE82.722A%praxis@techpraxis.com>
next in thread | raw e-mail | index | archive | help
A Call for help from the excellence of this list:
My FreeBSD box is giving me TROUBLE.... If someone could detect what is
wrong, and if it is a bug, please tell me how to submit it to the kernel
people...
I have two ethernet interfaces, a 3Com 905C-TX that is flawless so far, it
uses the "xl" driver, and an onboard LAN port that was autodetected at
FreeBSD install and assigned the "sis" driver.
Description of problem: seconds after pluggin' my second ethernet interface
into my switch, (also occurs plugged into a Netgear 10BT hub), no matter
what cat-5 cable I use(I switched out cables furiously), I get this message
on the console:
Mymachine /kernel: sis0: watchdog timeout
Then ping yields:
Ping: sendto: Host is down
(repeats until Ctrl-C)
Description of freebsd system:
FreeBSD 4.3-BETA, running kernel compiled from sources.
Description of hardware:
Processor: Athlon 600 MHz
Motherboard: ECS K7ASA w/ AGP slot, two PCI Bus Master UDMA ports, 2 ATAPI
ea.
RAM: 256 MB PC 100 SDRAM, 3.3V unbuffered DIMMS.
---> Embedded Network interface:
Here is the results of /sbin/dmesg:
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 598839452 Hz
CPU: AMD Athlon(tm) Processor (598.84-MHz 686-class CPU)
Origin = "AuthenticAMD" Id = 0x621 Stepping = 1
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,
PAT,PSE36,MMX,FXSR>
AMD Features=0xc0400000<AMIE,DSP,3DNow!>
real memory = 134217728 (131072K bytes)
config> di sn0
config> di lnc0
config> di ie0
config> di fe0
config> di cs0
config> q
avail memory = 126726144 (123756K bytes)
Preloaded elf kernel "kernel" at 0xc03d5000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc03d509c.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <AMD-751 host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <AMD-751 PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <ATI Mach64-GB graphics accelerator> at 5.0 irq 11
isab0: <PCI to ISA bridge (vendor=1022 device=7408)> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <AMD 756 ATA66 controller> port 0xf000-0xf00f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
chip1: <PCI to Other bridge (vendor=1022 device=740b)> at device 7.3 on pci0
ohci0: <AMD-756 USB Controller> mem 0xefffe000-0xefffefff irq 9 at device
7.4 on pci0
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <AMD-756 USB Controller> on ohci0
usb0: USB revision 1.0
uhub0: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xd400-0xd47f mem
0xefffdf80-0xefffdfff irq 5 at device 10.0 on pci0
xl0: Ethernet address: 00:01:02:87:04:af
miibus0: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus0
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci0: <unknown card> (vendor=0x14f1, dev=0x1036) at 11.0 irq 9
ahc0: <Adaptec 2910/15/20/30C SCSI adapter> port 0xdc00-0xdcff mem
0xeffff000-0xefffffff irq 10 at device 12.0 on pci0
ahc0: Host Adapter Bios disabled. Using default SCSI device parameters
aic7850: Single Channel A, SCSI Id=7, 3/255 SCBs
sis0: <SiS 900 10/100BaseTX> port 0xcc00-0xccff mem 0xefffc000-0xefffcfff
irq 9
at device 14.0 on pci0
sis0: Ethernet address: 00:d0:09:53:6f:82
miibus1: <MII bus> on sis0
ukphy0: <Generic IEEE 802.3u media interface> on miibus1
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci0: <unknown card> (vendor=0x13f6, dev=0x0111) at 15.0 irq 10
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
IP Filter: v3.4.16 initialized. Default = pass all, Logging = enabled
ad0: 29314MB <IBM-DTLA-307030> [59560/16/63] at ata0-master UDMA66
acd0: CDROM <TOSHIBA CD-ROM XM-6102B> at ata1-master using PIO3
Waiting 5 seconds for SCSI devices to settle
Mounting root from ufs:/dev/ad0s2a
xl0: promiscuous mode enabled
sis0: watchdog timeout
sis0: watchdog timeout
and the result of ifconfig:
xl0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
inet <<ipaddress>> netmask 0xffffff00 broadcast 64.221.116.255
inet6 fe80::201:2ff:fe87:4af%xl0 prefixlen 64 scopeid 0x1
ether 00:01:02:87:04:af
media: autoselect (10baseT/UTP) status: active
supported media: autoselect 100baseTX <full-duplex> 100baseTX
10baseT/UTP <full-duplex> 10baseT/UTP 100baseTX <hw-loopback>
sis0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
inet 10.0.0.1 netmask 0xffffff00 broadcast 10.0.0.255
inet6 fe80::2d0:9ff:fe53:6f82%sis0 prefixlen 64 scopeid 0x2
ether 00:d0:09:53:6f:82
media: autoselect (100baseTX <full-duplex>) status: active
supported media: autoselect 100baseTX <full-duplex> 100baseTX
10baseT/UTP <full-duplex> 10baseT/UTP none
lp0: flags=8810<POINTOPOINT,SIMPLEX,MULTICAST> mtu 1500
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4
inet6 ::1 prefixlen 128
inet 127.0.0.1 netmask 0xff000000
ppp0: flags=8010<POINTOPOINT,MULTICAST> mtu 1500
faith0: flags=8000<MULTICAST> mtu 1500
gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
gif1: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
gif2: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
gif3: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
Any other details that help in troubleshooting can be provided on request.
Thank you,
Forrest H.
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?B6FAAE82.722A%praxis>