Date: Thu, 31 Mar 2016 09:36:37 +0300 From: Daniel Braniss <danny@cs.huji.ac.il> To: Erik Moe <e.moe@rcn.com> Cc: freebsd-arm <freeBSD-arm@freebsd.org> Subject: Re: Odroidc1+ stuck booting Message-ID: <CCC86C18-EE51-4A24-A9A1-4FDCBB28B198@cs.huji.ac.il> In-Reply-To: <EEAFAE63-3550-4862-924C-B8E7B68FC62E@cs.huji.ac.il> References: <687E2129-BE66-4CC9-9B30-D8DFB7A2FEF6@cs.huji.ac.il> <982FE02C-7BEC-4CA0-BCAE-FE6CC5C9CFB4@rcn.com> <B39CD871-7BE5-44EA-816A-42A80E34D8A7@rcn.com> <EEAFAE63-3550-4862-924C-B8E7B68FC62E@cs.huji.ac.il>
next in thread | previous in thread | raw e-mail | index | archive | help
oh, and if you feel generous your ODROIDC1.conf =E2=80=A6 thanks, danny > On 31 Mar 2016, at 09:31, Daniel Braniss <danny@cs.huji.ac.il> wrote: >=20 > hi Erik, > can you send me your > uboot > boot.ini > *.dtb > I=E2=80=99m pretty sure the issue is somewhere there then. > thanks, > danny >=20 >> On 31 Mar 2016, at 09:11, Erik Moe <e.moe@rcn.com> wrote: >>=20 >> I built a new image for my odriod-c1 for ssd from the latest sources = and had no issues and didn=E2=80=99t need to tweet anything. I don=E2=80=99= t have and odriod-c1+, but my understanding is there isn=E2=80=99t much = difference between the two. I am using the serial console. >>=20 >> = QA5:A;SVN:B72;POC:17F;STS:0;BOOT:0;INIT:10;BOOT:1;INIT:0;READ:0;CHECK:0;PA= SS:1; >> = ----------------------------------------------------------------------- >> * Welcome to Hardkernel's ODROID-C... (Built at 19:33:00 Dec 8 2014) = * >> = ----------------------------------------------------------------------- >> CPU : AMLogic S805 >> MEM : 1024MB (DDR3@792MHz) >> BID : HKC13C0001 >> S/N : HKC1CC037EBE4620 >> 0x0000009f >> check SD_boot_type:0x1 card_type:0x1 >> Loading U-boot...success. >>=20 >>=20 >> U-boot(odroidc@) (Jun 12 2015 - 17:31:14) >>=20 >> DRAM: 1 GiB >> relocation Offset is: 2ff1c000 >> MMC: SDCARD: 0, eMMC: 1 >> IR init is done! >> vpu clk_level =3D 3 >> set vpu clk: 182150000Hz, readback: 182150000Hz(0x701) >> mode =3D 6 vic =3D 4 >> set HDMI vic: 4 >> mode is: 6 >> viu chan =3D 1 >> config HPLL >> config HPLL done >> reconfig packet setting done >> MMC read: dev # 0, block # 33984, count 12288 ... 12288 blocks read: = OK >> There is no valid bmp file at the given address >> =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D >> Vendor: Man 035344 Snr 29cfee4e Rev: 8.0 Prod: SL08G >> Type: Removable Hard Disk >> Capacity: 7580.0 MB =3D 7.4 GB (15523840 x 512) >> ------------------------------------------------------------ >> Partition Start Sector Num Sectors Type >> 1 1134 131040 6 >> 2 132174 15391666 a5 >> =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D >> Net: Meson_Ethernet >> init suspend firmware done. (ret:0) >> Hit Enter key to stop autoboot -- : 0 >> exit abortboot: 0 >> reading boot.ini >>=20 >> 98 bytes read >> Loading boot.ini from mmc0:1 (vfat) >> Executing the script... >> setenv bootcmd "fatload mmc 0 0x100000 kernel.bin; go 0x100000" >> run bootcmd >> reading kernel.bin >>=20 >> 6055396 bytes read >> ## Starting application at 0x00100000 ... >> ARM Debug Architecture v7 >> 2 watchpoints and 3 breakpoints supported >> KDB: debugger backends: ddb >> KDB: current backend: ddb >> Copyright (c) 1992-2016 The FreeBSD Project. >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, = 1994 >> The Regents of the University of California. All rights = reserved. >> FreeBSD is a registered trademark of The FreeBSD Foundation. >> FreeBSD 11.0-CURRENT #4 43026a8(master)-dirty: Thu Mar 31 04:14:32 = CDT 2016 >> = root@dora:/usr/home/emoe/Projects/ARM/odroid-c1/obj/arm.armv6hf/usr/home/e= moe/Projects/ARM/src/sys/ODROIDC1 arm >> FreeBSD clang version 3.8.0 (tags/RELEASE_380/final 262564) (based on = LLVM 3.8.0) >> WARNING: WITNESS option enabled, expect reduced performance. >> VT: init without driver. >> Preloaded elf kernel "kernel" at 0xc07c5d6c. >> CPU: Cortex A5 rev 1 (Cortex-A core) >> Supported features: ARM_ISA THUMB2 JAZELLE THUMBEE ARMv4 Security_Ext >> WB enabled LABT branch prediction disabled >> LoUU:2 LoC:2 LoUIS:2 >> Cache level 1: >> 32KB/32B 4-way data cache WB Read-Alloc Write-Alloc >> 32KB/32B 2-way instruction cache Read-Alloc >> real memory =3D 1073737728 (1023 MB) >> avail memory =3D 1038233600 (990 MB) >> Physical memory chunk(s): >> 0x00001000 - 0x3fffffff, 1023 MB ( 262143 pages) >> Excluded memory regions: >> 0x00100000 - 0x00853fff, 7 MB ( 1876 pages) NoAlloc >> Static device mappings: >> 0xc1100000 - 0xc12fffff mapped at VA 0xffd00000 >> 0xc4200000 - 0xc42fffff mapped at VA 0xffc00000 >> 0xc4300000 - 0xc43fffff mapped at VA 0xffb00000 >> 0xc8000000 - 0xc80fffff mapped at VA 0xffa00000 >> 0xc8100000 - 0xc81fffff mapped at VA 0xff900000 >> 0xc9000000 - 0xc97fffff mapped at VA 0xff100000 >> 0xd9000000 - 0xd90fffff mapped at VA 0xff000000 >> 0xda000000 - 0xda0fffff mapped at VA 0xfef00000 >> Amlogic aml8726-m8b SoC >> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs >> ULE: setup cpu 0 >> ULE: setup cpu 1 >> ULE: setup cpu 2 >> ULE: setup cpu 3 >> random: entropy device external interface >> null: <full device, null device, zero device> >> openfirm: <Open Firmware control device> >> mem: <memory> >> nfslock: pseudo-device >> crypto: <crypto core> >> random: harvesting attach, 8 bytes (4 bits) from nexus0 >> ofwbus0: <Open Firmware Device Tree> >> simplebus0: <Flattened device tree simple bus> on ofwbus0 >> random: harvesting attach, 8 bytes (4 bits) from simplebus0 >> random: harvesting attach, 8 bytes (4 bits) from ofwbus0 >> clkmsr0: <Amlogic aml8726 clkmsr> mem 0xc1108758-0xc1108767 on = simplebus0 >> clkmsr0: bus clock 159 MHz >> random: harvesting attach, 8 bytes (4 bits) from clkmsr0 >> l2cache0: <PL310 L2 cache controller> mem 0xc4200000-0xc4200fff irq 0 = on ofwbus0 >> l2cache0: Part number: 0x3, release: 0x9 >> l2cache0: L2 Cache enabled: 512KB/32B 8 ways >> l2cache0: Early BRESP response: disabled >> l2cache0: Instruction prefetch: disabled >> l2cache0: Data prefetch: enabled >> l2cache0: Non-secure interrupt control: disabled >> l2cache0: Non-secure lockdown: disabled >> l2cache0: Share override: disabled >> l2cache0: Double linefill: disabled >> l2cache0: Instruction prefetch: disabled >> l2cache0: Data prefetch: enabled >> l2cache0: Double linefill on WRAP request: disabled >> l2cache0: Prefetch drop: disabled >> l2cache0: Incr double Linefill: disabled >> l2cache0: Not same ID on exclusive sequence: disabled >> l2cache0: Prefetch offset: 0 >> random: harvesting attach, 8 bytes (4 bits) from l2cache0 >> scu0: <ARM Snoop Control Unit> mem 0xc4300000-0xc4300fff on = simplebus0 >> random: harvesting attach, 8 bytes (4 bits) from scu0 >> cpuconfig0: <Amlogic CPU Config> mem 0xd901ff80-0xd901ff8f on = simplebus0 >> random: harvesting attach, 8 bytes (4 bits) from cpuconfig0 >> ccm0: <Amlogic aml8726 ccm> mem 0xc1104140-0xc1104153 on simplebus0 >> random: harvesting attach, 8 bytes (4 bits) from ccm0 >> pinctrl0: <Amlogic aml8726 pinctrl> mem = 0xc11080b0-0xc11080d7,0xc11080e8-0xc11080ff,0xc1108120-0xc1108137,0xc81000= 14-0xc8100017,0xc810002c-0xc810002f,0xc810002c-0xc810002f on simplebus0 >> Processing 3 pin-config node(s) in pinctrl-0 for pinctrl@c11080b0 >> Processing 1 pin-config node(s) in pinctrl-0 for mmc@c1108c20 >> Processing 1 pin-config node(s) in pinctrl-0 for sdxc@c1108e00 >> random: harvesting attach, 8 bytes (4 bits) from pinctrl0 >> gic0: <ARM Generic Interrupt Controller> mem = 0xc4301000-0xc4301fff,0xc4300100-0xc43001ff on ofwbus0 >> ofwbus0: no default resources for rid =3D 0, type =3D 1 >> gic0: pn 0x390, arch 0x1, rev 0x1, implementer 0x43b irqs 256 >> random: harvesting attach, 8 bytes (4 bits) from gic0 >> wdt0: <Amlogic aml8726 WDT> mem 0xc1109900-0xc1109907 irq 2 on = simplebus0 >> random: harvesting attach, 8 bytes (4 bits) from wdt0 >> timer0: <Amlogic aml8726 timer> mem 0xc1109940-0xc1109957 irq 1 on = ofwbus0 >> Event timer "aml8726 timer A" frequency 1000000 Hz quality 1000 >> Timecounter "aml8726 timer E" frequency 1000000 Hz quality 1000 >> random: harvesting attach, 8 bytes (4 bits) from timer0 >> uart0: <Amlogic aml8726 UART> mem 0xc81004c0-0xc81004d7 irq 3 on = simplebus0 >> uart0: RTS iflow, CTS oflow >> uart0: console (115200,n,8,1) >> uart0: fast interrupt >> uart0: PPS capture mode: DCDinvalid >> random: harvesting attach, 8 bytes (4 bits) from uart0 >> uart1: <Amlogic aml8726 UART> mem 0xc11084c0-0xc11084d7 irq 4 on = simplebus0 >> uart1: RTS iflow, CTS oflow >> uart1: fast interrupt >> uart1: PPS capture mode: DCDinvalid >> random: harvesting attach, 8 bytes (4 bits) from uart1 >> uart2: <Amlogic aml8726 UART> mem 0xc11084dc-0xc11084f3 irq 5 on = simplebus0 >> uart2: RTS iflow, CTS oflow >> uart2: fast interrupt >> uart2: PPS capture mode: DCDinvalid >> random: harvesting attach, 8 bytes (4 bits) from uart2 >> uart3: <Amlogic aml8726 UART> mem 0xc1108700-0xc1108717 irq 6 on = simplebus0 >> uart3: RTS iflow, CTS oflow >> uart3: fast interrupt >> uart3: PPS capture mode: DCDinvalid >> random: harvesting attach, 8 bytes (4 bits) from uart3 >> simplebus0: <i2c@c8100500> mem 0xc8100500-0xc810051f irq 7 disabled = compat amlogic,meson6-i2c (no driver attached) >> aml8726_iic0: <Amlogic aml8726 I2C> mem 0xc1108500-0xc110851f irq 8 = on simplebus0 >> iicbb0: <I2C bit-banging driver> on aml8726_iic0 >> iicbus0: <Philips I2C bus> on iicbb0 master-only >> iic0: <I2C generic I/O> on iicbus0 >> random: harvesting attach, 8 bytes (4 bits) from iic0 >> random: harvesting attach, 8 bytes (4 bits) from iicbus0 >> random: harvesting attach, 8 bytes (4 bits) from iicbb0 >> random: harvesting attach, 8 bytes (4 bits) from aml8726_iic0 >> aml8726_iic1: <Amlogic aml8726 I2C> mem 0xc11087c0-0xc11087df irq 9 = on simplebus0 >> iicbb1: <I2C bit-banging driver> on aml8726_iic1 >> iicbus1: <Philips I2C bus> on iicbb1 master-only >> iic1: <I2C generic I/O> on iicbus1 >> random: harvesting attach, 8 bytes (4 bits) from iic1 >> random: harvesting attach, 8 bytes (4 bits) from iicbus1 >> random: harvesting attach, 8 bytes (4 bits) from iicbb1 >> random: harvesting attach, 8 bytes (4 bits) from aml8726_iic1 >> simplebus0: <ir-receiver@c8100480> mem 0xc8100480-0xc810049f irq 10 = disabled compat amlogic,meson6-ir (no driver attached) >> simplebus0: <spi@c1108c80> mem 0xc1108c80-0xc1108cff disabled compat = amlogic,meson6-spifc (no driver attached) >> simplebus0: <ethernet@c9410000> mem = 0xc9410000-0xc941ffff,0xc1108108-0xc110810b irq 11 disabled compat = amlogic,meson6-dwmac (no driver attached) >> rtc0: <Amlogic aml8726 RTC> mem 0xc8100740-0xc8100753 irq 12 on = simplebus0 >> rtc0: crystal oscillator check failed >> device_attach: rtc0 attach returned 6 >> gpio0: <Amlogic aml8726 GPIO> mem = 0xc8100024-0xc8100027,0xc8100024-0xc8100027,0xc8100028-0xc810002b on = simplebus0 >> gpiobus0: <OFW GPIO bus> on gpio0 >> gpioled0: <GPIO led> at pin 13 on gpiobus0 >> random: harvesting attach, 8 bytes (4 bits) from gpioled0 >> random: harvesting attach, 8 bytes (4 bits) from gpiobus0 >> gpioc0: <GPIO controller> on gpio0 >> random: harvesting attach, 8 bytes (4 bits) from gpioc0 >> random: harvesting attach, 8 bytes (4 bits) from gpio0 >> gpio1: <Amlogic aml8726 GPIO> mem = 0xc1108054-0xc1108057,0xc1108058-0xc110805b,0xc110805c-0xc110805f on = simplebus0 >> gpiobus1: <OFW GPIO bus> on gpio1 >> random: harvesting attach, 8 bytes (4 bits) from gpiobus1 >> gpioc1: <GPIO controller> on gpio1 >> random: harvesting attach, 8 bytes (4 bits) from gpioc1 >> random: harvesting attach, 8 bytes (4 bits) from gpio1 >> gpio2: <Amlogic aml8726 GPIO> mem = 0xc110806c-0xc110806f,0xc1108070-0xc1108073,0xc1108074-0xc1108077 on = simplebus0 >> gpiobus2: <OFW GPIO bus> on gpio2 >> random: harvesting attach, 8 bytes (4 bits) from gpiobus2 >> gpioc2: <GPIO controller> on gpio2 >> random: harvesting attach, 8 bytes (4 bits) from gpioc2 >> random: harvesting attach, 8 bytes (4 bits) from gpio2 >> aml8726_mmc0: <Amlogic aml8726 MMC> mem 0xc1108c20-0xc1108c3f irq 13 = on simplebus0 >> mmc0: <MMC/SD bus> on aml8726_mmc0 >> random: harvesting attach, 8 bytes (4 bits) from mmc0 >> random: harvesting attach, 8 bytes (4 bits) from aml8726_mmc0 >> aml8726_sdxc0: <Amlogic aml8726-m8 SDXC> mem 0xc1108e00-0xc1108e3b = irq 14 on simplebus0 >> mmc1: <MMC/SD bus> on aml8726_sdxc0 >> random: harvesting attach, 8 bytes (4 bits) from mmc1 >> random: harvesting attach, 8 bytes (4 bits) from aml8726_sdxc0 >> simplebus0: <rng@c1108100> mem 0xc1108100-0xc1108107 compat = amlogic,aml8726-rng (no driver attached) >> usbphy0: <Amlogic aml8726-m8 USB PHY> mem 0xc1108800-0xc110881f on = simplebus0 >> random: harvesting attach, 8 bytes (4 bits) from usbphy0 >> usbphy1: <Amlogic aml8726-m8 USB PHY> mem 0xc1108820-0xc110883f on = simplebus0 >> random: harvesting attach, 8 bytes (4 bits) from usbphy1 >> dwcotg0: <DWC OTG 2.0 integrated USB controller> mem = 0xc9040000-0xc907ffff irq 15 on simplebus0 >> usbus0 on dwcotg0 >> dwcotg0: usbpf: Attached >> random: harvesting attach, 8 bytes (4 bits) from usbus0 >> random: harvesting attach, 8 bytes (4 bits) from dwcotg0 >> dwcotg1: <DWC OTG 2.0 integrated USB controller> mem = 0xc90c0000-0xc90fffff irq 16 on simplebus0 >> usbus1 on dwcotg1 >> dwcotg1: usbpf: Attached >> random: harvesting attach, 8 bytes (4 bits) from usbus1 >> random: harvesting attach, 8 bytes (4 bits) from dwcotg1 >> dwc0: <Amlogic Meson Gigabit Ethernet Controller> mem = 0xc9410000-0xc9411fff irq 11 on simplebus0 >> miibus0: <MII bus> on dwc0 >> rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 0 on = miibus0 >> rgephy0: OUI 0x00e04c, model 0x0011, rev. 6 >> rgephy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, = 1000baseT-FDX, 1000baseT-FDX-master, auto >> random: harvesting attach, 8 bytes (4 bits) from rgephy0 >> rgephy1: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on = miibus0 >> rgephy1: OUI 0x00e04c, model 0x0011, rev. 6 >> rgephy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, = 1000baseT-FDX, 1000baseT-FDX-master, auto >> random: harvesting attach, 8 bytes (4 bits) from rgephy1 >> random: harvesting attach, 8 bytes (4 bits) from miibus0 >> dwc0: bpf attached >> dwc0: Ethernet address: 62:73:64:5d:6a:ec >> random: harvesting attach, 8 bytes (4 bits) from dwc0 >> fb0: <Amlogic aml8726 FB> mem = 0xc8006048-0xc8006053,0xc1106800-0xc1106bff,0xc1107400-0xc11077ff irq = 17,18,19,20 on simplebus0 >> fbd0 on fb0 >> VT: initialize with new VT driver "fb". >> random: harvesting attach, 8 bytes (4 bits) from fbd0 >> random: harvesting attach, 8 bytes (4 bits) from fb0 >> cpulist0: <Open Firmware CPU Group> on ofwbus0 >> cpu0: <Open Firmware CPU> on cpulist0 >> cpu0: missing 'clock-frequency' property >> random: harvesting attach, 8 bytes (4 bits) from cpu0 >> cpu1: <Open Firmware CPU> on cpulist0 >> cpu1: missing 'clock-frequency' property >> random: harvesting attach, 8 bytes (4 bits) from cpu1 >> cpu2: <Open Firmware CPU> on cpulist0 >> cpu2: missing 'clock-frequency' property >> random: harvesting attach, 8 bytes (4 bits) from cpu2 >> cpu3: <Open Firmware CPU> on cpulist0 >> cpu3: missing 'clock-frequency' property >> random: harvesting attach, 8 bytes (4 bits) from cpu3 >> random: harvesting attach, 8 bytes (4 bits) from cpulist0 >> ofwbus0: <clk@0> compat fixed-clock (no driver attached) >> ofwbus0: <leds> compat gpio-leds (no driver attached) >> cryptosoft0: <software crypto> >> crypto: assign cryptosoft0 driver id 0, flags 100663296 >> crypto: cryptosoft0 registers alg 1 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 2 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 3 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 4 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 5 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 16 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 6 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 7 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 18 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 19 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 20 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 8 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 15 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 9 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 10 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 13 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 14 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 11 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 22 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 23 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 25 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 24 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 26 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 27 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 28 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 21 flags 0 maxoplen 0 >> crypto: cryptosoft0 registers alg 17 flags 0 maxoplen 0 >> random: harvesting attach, 8 bytes (4 bits) from cryptosoft0 >> procfs registered >> Timecounters tick every 10.000 msec >> tcp_init: net.inet.tcp.tcbhashsize auto tuned to 8192 >> usbus0: 480Mbps High Speed USB v2.0 >> IPsec: Initialized Security Association Processing. >> lo0: bpf attached >> mmc0: Probing bus >> usbus1: 480Mbps High Speed USB v2.0 >> mmc0: SD 2.0 interface conditions: OK >> mmc0: SD probe: OK (OCR: 0x40ff8000) >> mmc0: Current OCR: 0x00ff8000 >> ugen1.1: <DWCOTG> at usbus1 >> uhub0: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on = usbus1 >> ugen0.1: <DWCOTG> at usbus0 >> uhub1: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on = usbus0 >> mmc0: Probing cards >> mmc0: New card detected (CID 035344534c3038478029cfee4e00f900) >> mmc0: New card detected (CSD 400e00325b5900003b377f800a404000) >> mmc0: Card at relative address 0xaaaa added: >> mmc0: card: SDHC SL08G 8.0 SN 29CFEE4E MFG 09/2015 by 3 SD >> mmc0: bus: 4bit, 50MHz, high speed timing >> mmc0: memory: 15523840 blocks, erase sector 8192 blocks >> mmc0: setting transfer rate to 39.750MHz (high speed timing) >> mmcsd0: 8GB <SDHC SL08G 8.0 SN 29CFEE4E MFG 09/2015 by 3 SD> at mmc0 = 39.7MHz/4bit/8-block >> random: harvesting attach, 8 bytes (4 bits) from mmcsd0 >> mmc1: Probing bus >> GEOM: new disk mmcsd0 >> mmc0: setting bus width to 4 bits >> GEOM_PART: partition 1 on (mmcsd0, MBR) is not aligned on 4194304 = bytes >> GEOM_PART: partition 2 on (mmcsd0, MBR) is not aligned on 4194304 = bytes >> mmc1: SD probe: failed >> mmc1: MMC probe: failed >> mmc1: Current OCR: 0x00000000 >> mmc1: No compatible cards found on bus >> Release APs >> WARNING: WITNESS option enabled, expect reduced performance. >> Trying to mount root from ufs:mmcsd0s2 []... >> GEOM_PART: partition 1 on (mmcsd0s2, BSD) is not aligned on 4194304 = bytes >> GEOM_PART: partition 1 on (diskid/DISK-29CFEE4E, MBR) is not aligned = on 4194304 bytes >> GEOM_PART: partition 2 on (diskid/DISK-29CFEE4E, MBR) is not aligned = on 4194304 bytes >> GEOM_PART: partition 1 on (diskid/DISK-29CFEE4Es2, BSD) is not = aligned on 4194304 bytes >> warning: no time-of-day clock registered, system time will not be set = accurately >> start_init: trying /sbin/init >> uhub0: 1 port with 1 removable, self powered >> random: harvesting attach, 8 bytes (4 bits) from uhub0 >> uhub1: 1 port with 1 removable, self powered >> random: harvesting attach, 8 bytes (4 bits) from uhub1 >> ugen1.2: <vendor 0x05e3> at usbus1 >> uhub2: <vendor 0x05e3 USB2.0 Hub, class 9/0, rev 2.00/32.98, addr 2> = on usbus1 >> uhub2: MTT enabled >> Growing root partition to fill device >> GEOM_PART: partition 1 on (diskid/DISK-29CFEE4E, MBR) is not aligned = on 4194304 bytes >> GEOM_PART: partition 2 on (diskid/DISK-29CFEE4E, MBR) is not aligned = on 4194304 bytes >> GEOM_PART: partition 1 on (diskid/DISK-29CFEE4Es2, BSD) is not = aligned on 4194304 bytes >> mmcsd0s2 resized >> growfs: superblock not recognized >> /etc/rc: WARNING: hostid: unable to figure out a UUID from DMI data, = generating a new one >> uhub2: 4 ports with 4 removable, self powered >> random: harvesting attach, 8 bytes (4 bits) from uhub2 >> Setting hostuuid: 214610b1-f72e-11e5-8203-df073412266c. >> Setting hostid: 0x373425ad. >> No suitable dump device was found. >> Starting file system checks: >> /dev/mmcsd0s2: FILE SYSTEM CLEAN; SKIPPING CHECKS >> /dev/mmcsd0s2: clean, 36687 free (103 frags, 4573 blocks, 0.0% = fragmentation) >> GEOM_PART: partition 1 on (mmcsd0s2, BSD) is not aligned on 4194304 = bytes >> GEOM_PART: partition 1 on (diskid/DISK-29CFEE4E, MBR) is not aligned = on 4194304 bytes >> GEOM_PART: partition 2 on (diskid/DISK-29CFEE4E, MBR) is not aligned = on 4194304 bytes >> GEOM_PART: partition 1 on (diskid/DISK-29CFEE4Es2, BSD) is not = aligned on 4194304 bytes >> Mounting local file systems:. >> Setting hostname: freebsd. >> Setting up = harvesting:[UMA],[FS_ATIME],SWI,INTERRUPT,NET_NG,NET_ETHER,NET_TUN,MOUSE,K= EYBOARD,ATTACH,CACHED >> Feeding entropy:random: unblocking device. >> . >> dwc0: link state changed to DOWN >> Starting Network: lo0 dwc0. >> lo0: flags=3D8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 >> options=3D600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6> >> inet6 ::1 prefixlen 128 >> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2 >> inet 127.0.0.1 netmask 0xff000000 >> groups: lo >> nd6 options=3D21<PERFORMNUD,AUTO_LINKLOCAL> >> dwc0: flags=3D8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 = mtu 1500 >> options=3D80008<VLAN_MTU,LINKSTATE> >> ether 62:73:64:5d:6a:ec >> media: Ethernet autoselect (none) >> status: no carrier >> nd6 options=3D29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> >> ELF ldconfig path: /lib /usr/lib /usr/lib/compat >> Starting devd. >> add net fe80::: gateway ::1 >> add net ff02::: gateway ::1 >> add net ::ffff:0.0.0.0: gateway ::1 >> add net ::0.0.0.0: gateway ::1 >> Generating host.conf. >> Waiting 30s for the default route interface: .....(no carrier) >> Creating and/or trimming log files. >> Starting syslogd. >> Clearing /tmp (X related). >> Updating motd:. >> Mounting late file systems:. >> Configuring vt: blanktime. >> Generating RSA host key. >> 2048 SHA256:efid4fCpKZlmdi69b18qj+SNx2mSPQNr6ourB/w9tPw root@freebsd = (RSA) >> Generating ECDSA host key. >> 256 SHA256:bpBVM0B9a3xDhmy3bvoC4OuELAJ4fvJd+p3tNwgia6k root@freebsd = (ECDSA) >> Generating ED25519 host key. >> 256 SHA256:VHMKoDA1Zv50CmxiLJwTIvg58S2DuBg6zj2VFXDGq/M root@freebsd = (ED25519) >> Performing sanity check on sshd configuration. >> Could not load host key: /etc/ssh/ssh_host_dsa_key >> Starting sshd. >> Could not load host key: /etc/ssh/ssh_host_dsa_key >> Starting cron. >> Starting background file system checks in 60 seconds. >> lock order reversal: >> 1st 0xc4499814 ufs (ufs) @ = /usr/home/emoe/Projects/ARM/src/sys/kern/vfs_subr.c:2498 >> 2nd 0xd90169a0 bufwait (bufwait) @ = /usr/home/emoe/Projects/ARM/src/sys/ufs/ffs/ffs_vnops.c:263 >> 3rd 0xc45c15d4 ufs (ufs) @ = /usr/home/emoe/Projects/ARM/src/sys/kern/vfs_subr.c:2498 >> stack backtrace: >> mount: /dev/mmcsd0s2: Device busy >>=20 >> Thu Mar 31 10:49:29 UTC 2016 >>=20 >> FreeBSD/arm (freebsd) (ttyu0) >>=20 >> login: >>=20 >>> On Mar 30, 2016, at 7:47 PM, Erik Moe <e.moe@rcn.com> wrote: >>>=20 >>> I was able to build a working odroid-c1 image not too long ago. Let = me pull the latest sources and see if something has changed. >>>=20 >>> Erik=20 >>>=20 >>>> On Mar 30, 2016, at 2:24 AM, Daniel Braniss <danny@cs.huji.ac.il> = wrote: >>>>=20 >>>> Hi, >>>> Managed to make a bootable SD, cross compile world/kernel, >>>> but the kernel startup gets stuck, I can=E2=80=99t even get into = the debugger. >>>> any help/hints most welcome :-) >>>> btw, I can also boot via the network, cutting down the debug cycle = considerably. >>>> thanks, >>>> danny >>>> PS: here is the console output >>>> <s1> >>>> _______________________________________________ >>>> freebsd-arm@freebsd.org mailing list >>>> https://lists.freebsd.org/mailman/listinfo/freebsd-arm >>>> To unsubscribe, send any mail to = "freebsd-arm-unsubscribe@freebsd.org" >>> _______________________________________________ >>> freebsd-arm@freebsd.org mailing list >>> https://lists.freebsd.org/mailman/listinfo/freebsd-arm >>> To unsubscribe, send any mail to = "freebsd-arm-unsubscribe@freebsd.org" >>=20 >=20 > _______________________________________________ > freebsd-arm@freebsd.org mailing list > https://lists.freebsd.org/mailman/listinfo/freebsd-arm > To unsubscribe, send any mail to "freebsd-arm-unsubscribe@freebsd.org"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?CCC86C18-EE51-4A24-A9A1-4FDCBB28B198>