Date: Thu, 25 Jul 2019 14:17:14 +0000 From: Mariappan N <nmarijoe@outlook.com> To: "freebsd-usb@freebsd.org" <freebsd-usb@freebsd.org> Subject: Problem attaching USB Garmin device Message-ID: <MAXPR01MB2944036F77333AE51E8EE717C5C10@MAXPR01MB2944.INDPRD01.PROD.OUTLOOK.COM>
index | next in thread | raw e-mail
[-- Attachment #1 --]
Hi Team,
I have Garmin GPSMAP device which can connect via USB. Installed FreeBSD 11.3 and tried to connect Garmin via USB 3.0 port however device not get detected/enumerated. When going through dmesg following error shows. When the device connect to windows/Linux machine, it's works fine but fails with FreeBSD. I am new to FreeBSD. Any suggestion to be appreciated 🙂.
dmesg log:
$ dmesg
usb_alloc_device: set address 2 failed (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_IOERROR
usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_IOERROR
usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_IOERROR
usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_IOERROR
usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_IOERROR
ugen0.2: <Unknown > at usbus0 (disconnected)
uhub_reattach_port: could not allocate new device
usbconfig list:
ugen2.1: <AMD EHCI root HUB> at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA)
ugen1.1: <AMD EHCI root HUB> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA)
ugen0.1: <0x1022 XHCI root HUB> at usbus0, cfg=0 md=HOST spd=SUPER (5.0Gbps) pwr=SAVE (0mA)
ugen1.2: <vendor 0x0438 product 0x7900> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (100mA)
ugen2.2: <vendor 0x0438 product 0x7900> at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (100mA)
ugen2.3: <PixArt Dell MS116 USB Optical Mouse> at usbus2, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON (100mA)
ugen1.3: <DELL Dell USB Entry Keyboard> at usbus1, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON (100mA)
I even tried with tunable USB timings using sysctl command but nothing works as expected. Also attached complete dmesg as a file. Please look into it.
Thanks
Mari
[-- Attachment #2 --]
mptable_probe: MP Config Table has bad signature: ~\^B\M-p
Copyright (c) 1992-2019 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.3-RELEASE #0 r349754: Fri Jul 5 04:31:33 UTC 2019
root@releng2.nyi.freebsd.org:/usr/obj/usr/src/sys/GENERIC i386
FreeBSD clang version 8.0.0 (tags/RELEASE_800/final 356365) (based on LLVM 8.0.0)
VT(vga): resolution 640x480
CPU: AMD GX-424CC SOC with Radeon(TM) R5E Graphics (2395.56-MHz 686-class CPU)
Origin="AuthenticAMD" Id=0x730f01 Family=0x16 Model=0x30 Stepping=1
Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
Features2=0x7ed8220b<SSE3,PCLMULQDQ,MON,SSSE3,CX16,SSE4.1,SSE4.2,MOVBE,POPCNT,AESNI,XSAVE,OSXSAVE,AVX,F16C,RDRAND>
AMD Features=0x2e500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM>
AMD Features2=0x1d4037ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS,SKINIT,WDT,Topology,PNXC,DBE,PTSC,PL2I>
Structured Extended Features=0x8<BMI1>
XSAVE Features=0x1<XSAVEOPT>
SVM: NP,NRIP,AFlush,DAssist,NAsids=8
TSC: P-state invariant, performance statistics
real memory = 8589934592 (8192 MB)
avail memory = 2549714944 (2431 MB)
Event timer "LAPIC" quality 600
ACPI APIC Table: <WYSE WYSEACPI>
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 1 package(s) x 4 core(s)
ioapic0: Changing APIC ID to 4
ioapic1: Changing APIC ID to 5
ioapic0 <Version 2.1> irqs 0-23 on motherboard
ioapic1 <Version 2.1> irqs 24-55 on motherboard
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #2 Launched!
random: entropy device external interface
kbd1 at kbdmux0
module_register_init: MOD_LOAD (vesa, 0xc1022f50, 0) error 19
random: registering fast source Intel Secure Key RNG
random: fast provider: "Intel Secure Key RNG"
nexus0
vtvga0: <VT VGA driver> on motherboard
cryptosoft0: <software crypto> on motherboard
acpi0: <WYSE> on motherboard
acpi0: Power Button (fixed)
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x71 on acpi0
atrtc0: registered as a time-of-day clock, resolution 1.000000s
Event timer "RTC" frequency 32768 Hz quality 0
attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff irq 0,8 on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pcib0: _OSC returned error 0x10
pci0: <ACPI PCI bus> on pcib0
vgapci0: <VGA-compatible display> port 0x3000-0x30ff mem 0xe0000000-0xefffffff,0xf0000000-0xf07fffff,0xf0d00000-0xf0d3ffff irq 44 at device 1.0 on pci0
vgapci0: Boot video device
hdac0: <ATI (0x9840) HDA Controller> mem 0xf0d60000-0xf0d63fff irq 45 at device 1.1 on pci0
pcib1: <ACPI PCI-PCI bridge> irq 48 at device 2.1 on pci0
pcib1: [GIANT-LOCKED]
pcib2: <ACPI PCI-PCI bridge> irq 49 at device 2.2 on pci0
pcib2: [GIANT-LOCKED]
pcib3: <ACPI PCI-PCI bridge> irq 50 at device 2.3 on pci0
pcib3: [GIANT-LOCKED]
pci1: <ACPI PCI bus> on pcib3
re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port 0x1000-0x10ff mem 0xf0b04000-0xf0b04fff,0xf0b00000-0xf0b03fff irq 32 at device 0.0 on pci1
re0: Using 1 MSI-X message
re0: Chip rev. 0x54000000
re0: MAC rev. 0x00100000
miibus0: <MII bus> on re0
rgephy0: <RTL8251 1000BASE-T media interface> PHY 1 on miibus0
rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
re0: Using defaults for TSO: 65518/35/2048
re0: Ethernet address: 00:80:64:ff:db:7c
pcib4: <ACPI PCI-PCI bridge> irq 51 at device 2.4 on pci0
pcib4: [GIANT-LOCKED]
pcib5: <ACPI PCI-PCI bridge> irq 48 at device 2.5 on pci0
pcib5: [GIANT-LOCKED]
pci0: <encrypt/decrypt> at device 8.0 (no driver attached)
xhci0: <AMD FCH USB 3.0 controller> mem 0xf0d68000-0xf0d69fff irq 18 at device 16.0 on pci0
xhci0: 32 bytes context size, 64-bit DMA
xhci0: Unable to map MSI-X table
usbus0 on xhci0
usbus0: 5.0Gbps Super Speed USB v3.0
ahci0: <AMD Hudson-2 AHCI SATA controller> port 0x3118-0x311f,0x3124-0x3127,0x3110-0x3117,0x3120-0x3123,0x3100-0x310f mem 0xf0d6d000-0xf0d6d3ff irq 19 at device 17.0 on pci0
ahci0: AHCI v1.30 with 1 6Gbps ports, Port Multiplier supported with FBS
ahcich0: <AHCI channel> at channel 0 on ahci0
ehci0: <AMD FCH USB 2.0 controller> mem 0xf0d6d500-0xf0d6d5ff irq 18 at device 18.0 on pci0
usbus1: EHCI version 1.0
usbus1 on ehci0
usbus1: 480Mbps High Speed USB v2.0
ehci1: <AMD FCH USB 2.0 controller> mem 0xf0d6d400-0xf0d6d4ff irq 18 at device 19.0 on pci0
usbus2: EHCI version 1.0
usbus2 on ehci1
usbus2: 480Mbps High Speed USB v2.0
hdac1: <AMD Hudson-2 HDA Controller> mem 0xf0d64000-0xf0d67fff irq 16 at device 20.2 on pci0
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
acpi_syscontainer0: <System Container> on acpi0
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xc0000-0xce7ff pnpid ORM0000 on isa0
ata0: <ATA channel> at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata1: <ATA channel> at port 0x170-0x177,0x376 irq 15 on isa0
ppc0: parallel port not found.
hwpstate0: <Cool`n'Quiet 2.0> on cpu0
Timecounters tick every 1.000 msec
hdacc0: <ATI R6xx HDA CODEC> at cad 0 on hdac0
hdaa0: <ATI R6xx Audio Function Group> at nid 1 on hdacc0
pcm0: <ATI R6xx (HDMI)> at nid 3 on hdaa0
pcm1: <ATI R6xx (HDMI)> at nid 5 on hdaa0
hdacc1: <Realtek ALC221 HDA CODEC> at cad 0 on hdac1
hdaa1: <Realtek ALC221 Audio Function Group> at nid 1 on hdacc1
pcm2: <Realtek ALC221 (Analog)> at nid 23 and 24 on hdaa1
pcm3: <Realtek ALC221 (Front Analog Headphones)> at nid 33 on hdaa1
ugen2.1: <AMD EHCI root HUB> at usbus2
ugen1.1: <AMD EHCI root HUB> at usbus1
ugen0.1: <0x1022 XHCI root HUB> at usbus0
uhub0: <AMD EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
uhub1: <AMD EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
uhub2: <0x1022 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
ada0 at ahcich0 bus 0 scbus0 target 0 lun 0
ada0: <64GB SATA Flash Drive SFPS921D> ACS-3 ATA SATA 3.x device
ada0: Serial Number C2280765156000001720
ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 61057MB (125045424 512 byte sectors)
Trying to mount root from ufs:/dev/ada0s1a [rw]...
random: unblocking device.
uhub2: 4 ports with 4 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub0: 2 ports with 2 removable, self powered
lo0: link state changed to UP
re0: link state changed to DOWN
ugen1.2: <vendor 0x0438 product 0x7900> at usbus1
uhub3 on uhub1
uhub3: <vendor 0x0438 product 0x7900, class 9/0, rev 2.00/0.18, addr 2> on usbus1
ugen2.2: <vendor 0x0438 product 0x7900> at usbus2
uhub4 on uhub0
uhub4: <vendor 0x0438 product 0x7900, class 9/0, rev 2.00/0.18, addr 2> on usbus2
uhub4: 4 ports with 4 removable, self powered
uhub3: 4 ports with 4 removable, self powered
re0: link state changed to UP
ugen2.3: <PixArt Dell MS116 USB Optical Mouse> at usbus2
ums0 on uhub4
ums0: <PixArt Dell MS116 USB Optical Mouse, class 0/0, rev 2.00/1.00, addr 3> on usbus2
ums0: 3 buttons and [XYZ] coordinates ID=0
ugen1.3: <DELL Dell USB Entry Keyboard> at usbus1
ukbd0 on uhub3
ukbd0: <DELL Dell USB Entry Keyboard, class 0/0, rev 2.00/1.04, addr 3> on usbus1
kbd2 at ukbd0
usb_alloc_device: set address 2 failed (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_IOERROR
usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_IOERROR
usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_IOERROR
usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_IOERROR
usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_IOERROR
ugen0.2: <Unknown > at usbus0 (disconnected)
uhub_reattach_port: could not allocate new device
ugen0.2: <vendor 0x091e product 0x0003> at usbus0
ugen0.2: <vendor 0x091e product 0x0003> at usbus0 (disconnected)
help
Want to link to this message? Use this
URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?MAXPR01MB2944036F77333AE51E8EE717C5C10>