Date: Fri, 18 Sep 1998 19:19:04 +0200 (METDST) From: Michael Class <michaelc@hpbbse.bbn.hp.com> To: current@FreeBSD.ORG Subject: ncr and CAM still dont work for me Message-ID: <Pine.HPP.3.94.980918191827.20736A-100000@hpbbse.bbn.hp.com>
next in thread | raw e-mail | index | archive | help
Hello,
I am still unable to get my system up and running with cam. Even with ncr.c
rev. 1.129 the system hangs with
probe0(ncr0:0:0:0) extaneous data discarded
probe0(ncr0:0:0:0) COMMAND FAILED (9 0) @f086f600
ncr0: timeout nccb = f086XXXX (skip)
(lots of these lines follow)
and after a couple of minutes:
da0:ncr0:0:0:0 READ CAPACITY CDB: 25 0 0 0 0 0 0 0 0 0
da0:ncr0:0:0:0 error code 51
and that's it. (I have the messages written on paper, so there might be
some typos)
The system is a P6, 200Mhz, 64MB Ram and a 810 and 875
SCSI-Controller. But even if I removed the 810 and all devices but the
Micropolis Disk, I am getting the same error.
Enclosed is the relevant output of a boot from a pre-cam kernel.
Any suggestions?
Michael
-------------------------------------------------------------------------
michael class, viktor-renner str. 39, 72074 tuebingen, frg
E-Mail: michael_class@hp.com
Phone: +49 7031 14-3707 (work) +49 7071 81950 (private)
-------------------------------------------------------------------------
ncr0: <ncr 53c875 fast20 wide scsi> rev 0x03 int a irq 12 on pci0.11.0
ncr0: minsync=12, maxsync=137, maxoffs=16, 128 dwords burst, large dma fifo
ncr0: single-ended, open drain IRQ driver, using on-chip SRAM
ncr0: restart (scsi reset).
ncr0 scanning for targets 0..6 and 8..15 (V2 pl24 96/12/14)
ncr0: waiting for scsi devices to settle
scbus0 at ncr0 bus 0
sd0 at scbus0 target 0 lun 0
sd0: <MICROP 3391WS X502> type 0 fixed SCSI 2
sd0: Direct-Access
sd0: NCR quirks=0x2
sd0: WIDE SCSI (16 bit) enabled
sd0: 40.0 MB/s (50 ns, offset 15)
sd0: M_DISCONNECT received, but datapointer not saved:
data=35e590 save=f88006b0 goal=f88006d4.
8681MB (17780058 512 byte sectors)
sd0: with 4811 cyls, 22 heads, and an average 167 sectors/track
sd1 at scbus0 target 1 lun 0
sd1: <Quantum XP34300W L915> type 0 fixed SCSI 2
sd1: Direct-Access
sd1: NCR quirks=0x2
sd1: WIDE SCSI (16 bit) enabled
sd1: 20.0 MB/s (100 ns, offset 15)
4101MB (8399520 512 byte sectors)
sd1: with 3907 cyls, 20 heads, and an average 107 sectors/track
st0 at scbus0 target 3 lun 0
st0: <HP C1533A A612> type 1 removable SCSI 2
st0: Sequential-Access
st0: NCR quirks=0x2
st0: 10.0 MB/s (100 ns, offset 16)
density code 0x24, drive empty
found-> vendor=0x1000, dev=0x0001, revid=0x01
class=00-00-00, hdrtype=0x00, mfdev=0
intpin=a, irq=11
map[0]: type 4, range 32, base 0000d400, size 8
map[1]: type 1, range 32, base f8000000, size 8
ncr1: <ncr 53c810 fast10 scsi> rev 0x01 int a irq 11 on pci0.12.0
ncr1: minsync=25, maxsync=206, maxoffs=8, 16 dwords burst, normal dma fifo
ncr1: single-ended, open drain IRQ driver
ncr1: restart (scsi reset).
ncr1 scanning for targets 0..6 (V2 pl24 96/12/14)
ncr1: waiting for scsi devices to settle
scbus1 at ncr1 bus 0
worm0 at scbus1 target 3 lun 0
worm0: <HP C4324/C4325 1.27> type 5 removable SCSI 2
worm0: Write-Once
uk0 at scbus1 target 4 lun 0
uk0: <UMAX Astra 1200S V2.9> type 6 fixed SCSI 2
uk0: Unknown
scbus1 target 4 lun 1: NCR quirks=0x2
uk1 at scbus1 target 4 lun 1
uk1: <UMAX Astra 1200S V2.9> type 6 fixed SCSI 2
uk1: Unknown
uk2 at scbus1 target 4 lun 2
uk2: <UMAX Astra 1200S V2.9> type 6 fixed SCSI 2
uk2: Unknown
uk3 at scbus1 target 4 lun 3
uk3: <UMAX Astra 1200S V2.9> type 6 fixed SCSI 2
uk3: Unknown
uk4 at scbus1 target 4 lun 4
uk4: <UMAX Astra 1200S V2.9> type 6 fixed SCSI 2
uk4: Unknown
uk5 at scbus1 target 4 lun 5
uk5: <UMAX Astra 1200S V2.9> type 6 fixed SCSI 2
uk5: Unknown
uk6 at scbus1 target 4 lun 6
uk6: <UMAX Astra 1200S V2.9> type 6 fixed SCSI 2
uk6: Unknown
uk7 at scbus1 target 4 lun 7
uk7: <UMAX Astra 1200S V2.9> type 6 fixed SCSI 2
uk7: Unknown
cd0 at scbus1 target 5 lun 0
cd0: <TOSHIBA CD-ROM XM-3701TA 3615> type 5 removable SCSI 2
cd0: CD-ROM
cd0: NCR quirks=0x2
cd0: 4.0 MB/s (250 ns, offset 8)
cd present [296150 x 2048 byte records]
___________________________________________________________________________
Michael Class E-Mail: michael_class@hp.com
E-Business Solutions Center Phone: +49 7031 14-3707
EBSO-SERC Fax: +49 7031 14-4196
___________________________________________________________________________
Hewlett-Packard GmbH, PO Box 1430, 71004 Boeblingen
Sitz der Gesellschaft: Böblingen, Amtsgericht Böblingen HRB 4081
Geschäftsführer: Jörg Menno Harms (Vorsitzender), Heribert Schmitz,
Rudi Speier, Fritz Schuller, Hans-Günter Hohmann
___________________________________________________________________________
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.HPP.3.94.980918191827.20736A-100000>