Date: Tue, 7 Mar 2000 18:09:15 +0100 (CET) From: jojo@buchonline.net To: FreeBSDMobile <freebsd-mobile@FreeBSD.ORG> Subject: D-LINK DFE-650TX and Toshiba XDVD 2650 doesn't work! Message-ID: <200003071709.SAA09109@server.intrabol.local>
next in thread | raw e-mail | index | archive | help
Hello List,
i'm seeking for a solutions. I have searched the archiv, used the
dejanews and i have tried different setting without success.
I use FreeBSD 3.4 and PAO! The LEDs "Ln/Act" and "10/100" is flashing
periodic (ca. 1.sec) and i get "ed0 device timeout". The FAQ tell me,
there are an irq conflict. But i am not able to fetch the right irq,
because i'm a newbie in FreeBSD and i am missing the step by step
manual. I have found a dumpcis of DFE-650 via dejanews and i noticed the
difference at Tuple #6. From the archiv, i see "length=38" and my
dumpcis tell me, the length is 40. Maybe this is the reason of my
horror trip? Maybe, i get failure with Autonegotiaton? I am seeking for
the right setting in rc.conf too (media 100BaseTX mediaopts
half-duplex?).
Any hints, helps and suggestions are very welcome!
Thanks!
Regards,
Joachim
-----------------snipp-------------------
This is my dumpcis:
Configuration data for card in slot 0
Tuple #1, code = 0x1 (Common memory descriptor), length = 3
000: d1 3a ff
Common memory device information:
Device number 1, type Function specific, WPS = OFF
Speed = 250nS, Memory block size = 8Kb, 8 units
Tuple #2, code = 0x1c (Other conditions for common memory), length = 4
000: 01 d1 3a ff
(MWAIT)
Tuple #3, code = 0x17 (Attribute memory descriptor), length = 3
000: 41 00 ff
Attribute memory device information:
Device number 1, type EEPROM, WPS = OFF
Speed = 250nS, Memory block size = 512b, 1 units
Tuple #4, code = 0x20 (Manufacturer ID), length = 4
000: 49 01 30 02
PCMCIA ID = 0x149, OEM ID = 0x230
Tuple #5, code = 0x21 (Functional ID), length = 2
000: 06 01
Network/LAN adapter - POST initialize
Tuple #6, code = 0x15 (Version 1 info), length = 40
000: 04 01 44 2d 4c 69 6e 6b 00 44 46 45 2d 36 35 30
010: 00 46 61 73 74 20 45 74 68 65 72 6e 65 74 00 52
020: 65 76 2e 20 44 31 00 ff
Version = 4.1, Manuf = [D-Link], card vers = [DFE-650]
Addit. info = [Fast Ethernet],[Rev. D1]
Tuple #7, code = 0x1a (Configuration map), length = 5
000: 01 20 00 04 0b
Reg len = 2, config register addr = 0x400, last config = 0x20
Registers: XX-X----
Tuple #8, code = 0x1b (Configuration entry), length = 7
000: e0 81 18 45 30 fc be
Config index = 0x20(default)
Interface byte = 0x81 (I/O) wait signal supported
Card decodes 5 address lines, limited 8/16 Bit I/O
IRQ modes: Level
IRQs: 2 3 4 5 6 7 9 10 11 12 13 15
Tuple #9, code = 0x14 (No link), length = 0
Tuple #10, code = 0xff (Terminator), length = 0
2 slots found
-----------------snipp-------------------
This is my dmesg:
Copyright (c) 1992-1999 FreeBSD Inc.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 3.4-RELEASE #0: Tue Mar 7 17:18:51 CET 2000
root@freebsd.intrabol.local:/big/usr/src/sys/compile/Mobile_Kernel
Timecounter "i8254" frequency 1193152 Hz
CPU: Celeron (463.54-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x66a Stepping = 10
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,F
real memory = 67108864 (65536K bytes)
avail memory = 62156800 (60700K bytes)
Preloaded elf kernel "kernel" at 0xc02e6000.
Pentium Pro MTRR support enabled
Probing for devices on PCI bus 0:
chip0: <Intel 82443BX host to PCI bridge> rev 0x03 on pci0.0.0
chip1: <Intel 82443BX host to AGP bridge> rev 0x03 on pci0.1.0
chip2: <Intel 82371AB PCI to ISA bridge> rev 0x02 on pci0.5.0
ide_pci0: <Intel PIIX4 Bus-master IDE controller> rev 0x01 on pci0.5.1
uhci0: <Intel 82371AB/EB USB Host Controller> rev 0x01 int d irq 11 on pci0.5.2
chip3: <Intel 82371AB Power management controller> rev 0x03 on pci0.5.3
chip4: <PCI to CardBus bridge (vendor=1179 device=0617)> rev 0x20 int a irq 255 on pci0.11.0
chip5: <PCI to CardBus bridge (vendor=1179 device=0617)> rev 0x20 int b irq 255 on pci0.11.1
Probing for devices on PCI bus 1:
vga0: <Trident model 9525 VGA-compatible display device> rev 0x49 int a irq 11 on pci1.0.0
Probing for devices on PCI bus 2:
Probing for devices on PCI bus 3:
Probing for devices on PCI bus 4:
Probing for devices on PCI bus 5:
Probing for devices on PCI bus 6:
Probing for devices on PCI bus 7:
Probing for devices on PCI bus 8:
Probing for devices on PCI bus 9:
Probing for devices on PCI bus 10:
Probing for devices on PCI bus 11:
Probing for devices on PCI bus 12:
Probing for devices on PCI bus 13:
Probing for devices on PCI bus 14:
Probing for devices on PCI bus 15:
Probing for devices on PCI bus 16:
Probing for devices on PCI bus 17:
Probing for devices on PCI bus 18:
Probing for devices on PCI bus 19:
Probing for devices on PCI bus 20:
Probing for devices on PCI bus 21:
Probing for PnP devices:
Probing for devices on the ISA bus:
sc0 on isa
sc0: VGA color <16 virtual consoles, flags=0x0>
ed0 not found at 0x300
atkbdc0 at 0x60-0x6f on motherboard
atkbd0 irq 1 on isa
psm0 irq 12 on isa
psm0: model IntelliMouse, device ID 3
sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa
sio0: type 16550A
pca0 on motherboard
pca0: PC speaker audio driver
fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
fd0: 1.44MB 3.5in
wdc0 at 0x1f0-0x1f7 irq 14 on isa
wdc0: unit 0 (wd0): <IBM-DARA-206000>
wd0: 5729MB (11733120 sectors), 12416 cyls, 15 heads, 63 S/T, 512 B/S
ppc0 at 0x378 irq 7 flags 0x40 on isa
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
lpt0: <generic printer> on ppbus 0
lpt0: Interrupt-driven port
ppi0: <generic parallel i/o> on ppbus 0
plip0: <PLIP network interface> on ppbus 0
pcic0 at 0x3e0-0x3e1 irq 15 on isa
PC-Card ctlr(0) Intel 82365A/B (5 mem & 2 I/O windows)
pcic0: slot 0 controller I/O address 0x3e0
pcic0: slot 1 controller I/O address 0x3e0
vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa
npx0 on motherboard
npx0: INT 16 interface
apm0 on isa
apm: found APM BIOS version 1.2
usb0: <Intel 82371AB/EB USB Host Controller>
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
Initializing PC-card drivers: ed ep xe sio wdc
changing root device to wd0s2a
Card inserted, slot 0
sio0: 1 more silo overflow (total 1)
card0: assign ed0 iobase 0x240 irq 3 flags 0x10
ed0: address 01:d1:ff:04:d1:ff, type NE2000 (16 bit)
ed0: unload
Return IRQ=3
Card removed, slot 0
Card inserted, slot 0
card0: assign ed0 iobase 0x240 irq 3 flags 0x10
ed0: address 01:d1:ff:04:d1:ff, type NE2000 (16 bit)
-----------------snipp-------------------
and this is my kernelconfig
controller pci0
# PCCARD (PCMCIA) support - do not remove.
pseudo-device card 1
#controller card0
# You must use "flags 0x1" when you don't hear any negotiation noise(?)
# if you use modem card, or pccardd doesn't read cis tuple, tell you
# 'No card in database for"(null)"("(null)")' in case of Cirrus Logic's
# pcic is your PC.
#device pcic0 at card?
#device pcic0 at isa? port 0x3e0 irq 5
#device pcic0 at isa? port 0x400
device pcic0 at isa? port 0x3e0 irq 5
#device ed0 at isa? port 0x280 net irq 10 iomem 0xd8000
#device ed0 at isa? port 0x300 net irq 15 flags 0x14 iomem 0xd8000
device ed0
device ep0
device xe0
--
Hans-Joachim Leidinger
buch online jojo@buchonline.net
Munscheidstr. 14 FAX: +49 209 1971449
45886 Gelsenkirchen FAX: 0209 1671449
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200003071709.SAA09109>