Date: Fri, 16 Jul 2004 19:16:00 +0100 From: Feargal Reilly <feargal@chrysalink.net> To: freebsd-hardware@freebsd.org Subject: SATA RAID with Intel 300ESB chipset Message-ID: <20040716191600.282c3dc9@beaker.chrysalink.net>
next in thread | raw e-mail | index | archive | help
--Signature=_Fri__16_Jul_2004_19_16_00_+0100_HTskwW.lMrmAf9fy Content-Type: multipart/mixed; boundary="Multipart=_Fri__16_Jul_2004_19_16_00_+0100_0ALERQe1tlRtbN5Z" --Multipart=_Fri__16_Jul_2004_19_16_00_+0100_0ALERQe1tlRtbN5Z Content-Type: text/plain; charset=US-ASCII Content-Disposition: inline Content-Transfer-Encoding: 7bit Hi, I've been trying to install either FreeBSD 4.10 or 5.2.1 from CD onto a machine with the Intel SE7210TP motherboard. This has two 80G disks connected to an onboard RAID controller which, according to the documentation, is the Intel 300ESB I/O Controller Hub. If, in the BIOS, I map PATA and SATA to Legacy ATA, both 4.10 and 5.2.1 CDs boot and install fine. Obviously though that's downgrading my shiny new SATA disks. If I map PATA to Legacy ATA and enable SATA, then 5.2.1 boots and installs fine, but 4.10 hangs after kernel configuration, tail of log is: isa_probe_children: probing PnP devices BIOS Geometries: 0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors 1:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors 0 accounted for Device configuration finished. bpf: lo0 attached bpf: sl0 attached Full output is attached as 4.10-PATA+SATA.log Finally, if I enable SATA RAID and map PATA to Legacy ATA, both 4.10 and 5.2.1 boot from the CD, but neither recognises the RAID array; when I try to install, sysinstall tells me "No disks found!" and suggests my disk controller is not being properly probed. This happens whether I set up RAID-0, RAID-1, or no RAID array at all. I've tried pre-loading various modules in the hope that they would recognise the array, but to no avail. I'd seen Doug Ambrisko's patch from March which led me to believe that this controller was supported, but a quick look at the sources on other machines suggests that it wasn't committed. What's the best way forward for me? Ideal situation would be to get the RAID controller working on 4.10, but I'm not seeing any success with SATA at all so I'm guessing my best chance would be on 5.2.1. I would rather get the hardware working than go down the vinum route. This server doesn't have to be in action for a week or two, so I can forget about vinum until then. Here's the full output from the 5.2.1. SATA RAID attempt with a single RAID1 array, (the 4.10 attempt is attached): Serial Redir 2.0.5 [VT-100+] BIOS LAN Console 4.0 Copyright (C) 1997-2002 Intel Corporation AMIBIOS(C)2003 American Megatrends, Inc. BIOS Date: 12/25/03 13:42:43 Ver: 08.00.10 SE7210TP10 Production BIOS Version 01.00, Build 0023 CPU : Intel(R) Pentium(R) 4 CPU 3.20GHz Speed : 3.20 GHz Press <F2> to run Setup Press <F12> for Network Boot Press <ESC> for BBS POPUP DDR Frequency 400 Mhz, Dual-Channel Checking NVRAM.. Initializing USB Controllers .. Done. Testing system memory, memory size=1024MB 1024MB Extended Memory Passed (C)AmericanMegatrends,Inc. 64-0100-000023-00101111-122503-CANTWOOD-STP1A023-Y2KC System Event Log Full Auto-Detecting Pri Master..ATAPI CDROM Auto-Detecting 3rd Master..IDE Hard Disk Auto-Detecting 4th Master..IDE Hard Disk Pri Master: CREATIVEDVD1240E 3X14 Ultra DMA Mode-2 3rd Master: ST380013AS 3.18 Ultra DMA Mode-5, S.M.A.R.T. Capable and Status OK 4th Master: ST380013AS 3.18 Ultra DMA Mode-5, S.M.A.R.T. Capable and Status OK Auto-detecting USB Mass Storage Devices .. 00 USB mass storage devices found and configured. Adaptec Embedded SATA HostRAID BIOS V1.0-0 1024 (c) 1998-2003 Adaptec, Inc. All Rights Reserved. ... Press <Ctrl><A> for Adaptec RAID Configuration Utility! ... Controller #00: Adaptec HostRAID at PCI Bus:00, Dev:1F, Func:02 Waiting for Controller to Start....Controller started Port#00 ST380013AS 3.18 74.53 GB Healthy Port#01 ST380013AS 3.18 74.53 GB Healthy Array #0 - RAID-1 RAID1 74.53 GB Optimal 1 Logical Device(s) Found. +=============================================================== ============+| System Configuration, AMIBIOS Version 08.00.10 |+============================================================== =============+| Main Processor(s): Intel(R) Pentium(R) 4 CPU 3.20GHz |+============================================================== =============+| Math Processor : Built-In Base Memory Size : 640KB || Floppy Drive A: : 1.44 MB 3@" Extd Memory Size : 1023MB || Serial Port(s) : 3F8,2F8 Display Type : VGA/EGA || BIOS Build Date : 12/25/03 PS/2 Mouse : None || ACPI 1.0 Support : Enabled |+============================================================== =============+| ATA(PI) Device(s) Type Size LBA Block SMART 32Bit DMA PIO || Mode Mode Info Mode Mode Mode|| Primary Master : ATAPI CDROM UDMA2 4 |+============================================================== =============+| PCI Devices: || PCI Onboard PCI Bridge PCI Onboard PCI Bridge || PCI Onboard USB Controller,IRQ9 PCI Onboard System Device || PCI Onboard System Device PCI Onboard USB Controller,IRQ5 || PCI Onboard USB Controller,IRQ7 PCI Onboard PCI Bridge || PCI Onboard SerialBus Cntlr,IRQ5 PCI Onboard RAID,IRQ9 || PCI Onboard IDE PCI Bridge Ethernet,IRQ9 || PCI Bridge VGA,IRQ11 PCI Bridge Ethernet,IRQ5 |+============================================================== =============+ Press <ESC> to boot....1 CD Loader 1.01 Building the boot loader arguments Looking up /BOOT/LOADER... Found Relocating the loader and the BTX Starting the BTX loader BTX loader 1.00 BTX version is 1.01 Console: internal video/keyboard BIOS CD is cd0 BIOS drive A: is disk0 BIOS drive C: is disk1 BIOS 631kB/1047488kB available memory FreeBSD/i386 bootstrap loader, Revision 1.1 (root@wv1u.btc.adaptec.com, Mon Feb 23 18:35:51 GMT 2004) Loading /boot/defaults/loader.conf /boot/kernel/kernel text=0x45d64c data=0x7948c+0x47a10 syms=[0x4+0x57ee0+0x4+0x6 a2f2] / +-----------------------------------------+ | | | | , , | | /( )` | Welcome to FreeBSD! | \ \___ / | | | /- _ `-/ ' | | (/\/ \ \ /\ | 1. Boot FreeBSD [default] | / / | ` \ | 2. Boot FreeBSD with ACPI disabled | O O ) / | | 3. Boot FreeBSD in Safe Mode | `-^--'`< ' | 4. Boot FreeBSD in single user mode | (_.) _ ) / | 5. Boot FreeBSD with verbose logging | `.___/` / | 6. Escape to loader prompt | `-----' / | 7. Reboot | <----. __ / __ \ | | <----|====O)))==) \) /==== | | <----' `--' `.__,' \ | | | | | | \ / /\ | Select option, [Enter] for default | ______( (_ / \______/ | or [Space] to pause timer 9 | ,' ,-----' | +-----------------------------------------+ `--{__________) Type '?' for a list of commands, 'help' for more detailed help. OK boot -Dh -v /boot/kernel/acpi.ko text=0x3f088 data=0x1744+0x114c syms=[0x4+0x6b20+0x4+0x866e] -SMAP type=01 base=0000000000000000 len=000000000009dc00 SMAP type=02 base=000000000009dc00 len=0000000000002400 SMAP type=02 base=00000000000e0000 len=0000000000020000 SMAP type=01 base=0000000000100000 len=000000003fef0000 SMAP type=03 base=000000003fff0000 len=000000000000f000 SMAP type=04 base=000000003ffff000 len=0000000000001000 SMAP type=02 base=00000000ffb00000 len=0000000000500000 Copyright (c) 1992-2004 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.2.1-RELEASE #0: Mon Feb 23 20:45:55 GMT 2004 root@wv1u.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC Preloaded elf kernel "/boot/kernel/kernel" at 0xc0e6d000. Preloaded mfs_root "/boot/mfsroot" at 0xc0e6d204. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0e6d248. Table 'FACP' at 0x3fff0200 Table 'APIC' at 0x3fff0390 MADT: Found table at 0x3fff0390 MP Configuration Table version 1.4 found at 0xc00fbab0 APIC: Using the MADT enumerator. MADT: Found CPU APIC ID 0 ACPI ID 1: enabled SMP: Added CPU 0 (AP) MADT: Found CPU APIC ID 1 ACPI ID 2: enabled SMP: Added CPU 1 (AP) ACPI APIC Table: <A M I OEMAPIC > Calibrating clock(s) ... i8254 clock: 1193114 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 Calibrating TSC clock ... TSC clock: 3192008572 Hz CPU: Intel(R) Pentium(R) 4 CPU 3.20GHz (3192.01-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf29 Stepping = 9 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP, MTRR,PGE,MCA,CMO V,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Hyperthreading: 2 logical CPUs real memory = 1073676288 (1023 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009cfff, 638976 bytes (156 pages) 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages) 0x0000000001029000 - 0x000000003edc9fff, 1037701120 bytes (253345 pages) avail memory = 1029316608 (981 MB) APIC ID: physical 0, logical 0:0 APIC ID: physical 1, logical 0:1 FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 pnpbios: Found PnP BIOS data at 0xc00f4f30 pnpbios: Entry = f0000:5c34 Rev = 1.0 Other BIOS signatures found: APIC: CPU 0 has ACPI ID 1 APIC: CPU 1 has ACPI ID 2 MADT: Found IO APIC ID 2, Vector 0 at 0xfec00000 ioapic0: intpin 0 -> ExtINT (edge, activehi) ioapic0: intpin 1 -> irq 1 (edge, activehi) ioapic0: intpin 2 -> irq 2 (edge, activehi) ioapic0: intpin 3 -> irq 3 (edge, activehi) ioapic0: intpin 4 -> irq 4 (edge, activehi) ioapic0: intpin 5 -> irq 5 (edge, activehi) ioapic0: intpin 6 -> irq 6 (edge, activehi) ioapic0: intpin 7 -> irq 7 (edge, activehi) ioapic0: intpin 8 -> irq 8 (edge, activehi) ioapic0: intpin 9 -> irq 9 (edge, activehi) ioapic0: intpin 10 -> irq 10 (edge, activehi) ioapic0: intpin 11 -> irq 11 (edge, activehi) ioapic0: intpin 12 -> irq 12 (edge, activehi) ioapic0: intpin 13 -> irq 13 (edge, activehi) ioapic0: intpin 14 -> irq 14 (edge, activehi) ioapic0: intpin 15 -> irq 15 (edge, activehi) ioapic0: intpin 16 -> irq 16 (level, activelo) ioapic0: intpin 17 -> irq 17 (level, activelo) ioapic0: intpin 18 -> irq 18 (level, activelo) ioapic0: intpin 19 -> irq 19 (level, activelo) ioapic0: intpin 20 -> irq 20 (level, activelo) ioapic0: intpin 21 -> irq 21 (level, activelo) ioapic0: intpin 22 -> irq 22 (level, activelo) ioapic0: intpin 23 -> irq 23 (level, activelo) MADT: Found IO APIC ID 3, Vector 24 at 0xfec10000 ioapic1: intpin 0 -> irq 24 (level, activelo) ioapic1: intpin 1 -> irq 25 (level, activelo) ioapic1: intpin 2 -> irq 26 (level, activelo) ioapic1: intpin 3 -> irq 27 (level, activelo) ioapic1: intpin 4 -> irq 28 (level, activelo) ioapic1: intpin 5 -> irq 29 (level, activelo) ioapic1: intpin 6 -> irq 30 (level, activelo) ioapic1: intpin 7 -> irq 31 (level, activelo) ioapic1: intpin 8 -> irq 32 (level, activelo) ioapic1: intpin 9 -> irq 33 (level, activelo) ioapic1: intpin 10 -> irq 34 (level, activelo) ioapic1: intpin 11 -> irq 35 (level, activelo) ioapic1: intpin 12 -> irq 36 (level, activelo) ioapic1: intpin 13 -> irq 37 (level, activelo) ioapic1: intpin 14 -> irq 38 (level, activelo) ioapic1: intpin 15 -> irq 39 (level, activelo) ioapic1: intpin 16 -> irq 40 (level, activelo) ioapic1: intpin 17 -> irq 41 (level, activelo) ioapic1: intpin 18 -> irq 42 (level, activelo) ioapic1: intpin 19 -> irq 43 (level, activelo) ioapic1: intpin 20 -> irq 44 (level, activelo) ioapic1: intpin 21 -> irq 45 (level, activelo) ioapic1: intpin 22 -> irq 46 (level, activelo) ioapic1: intpin 23 -> irq 47 (level, activelo) MADT: intr override: source 0, irq 2 ioapic0: Routing IRQ 0 -> intpin 2 ioapic0: intpin 2 trigger: edge ioapic0: intpin 2 polarity: active-hi MADT: intr override: source 10, irq 10 ioapic0: intpin 10 trigger: level ioapic0: intpin 10 polarity: active-hi lapic0: Routing NMI -> LINT1 lapic1: Routing NMI -> LINT1 ioapic0 <Version 2.0> irqs 0-23 on motherboard ioapic1 <Version 2.0> irqs 24-47 on motherboard cpu0 BSP: ID: 0x00000000 VER: 0x00050014 LDR: 0x01000000 DFR: 0x0fffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff wlan: <802.11 Link Layer> null: <null device, zero device> random: <entropy source> mem: <memory & I/O> Pentium Pro MTRR support enabled npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <A M I OEMRSDT > on motherboard pci_open(1): mode 1 addr port (0x0cf8) is 0x80000090 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=25788086) pcibios: No call entry point pcibios: No call entry point AcpiOsDerivePciId: bus 0 dev 31 func 0 acpi0: Power Button (fixed) ACPI timer looks GOOD min = 3, max = 3, width = 0 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 3, width = 0 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 acpi_cpu0: <CPU> on acpi0 acpi_cpu1: <CPU> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 ---- initial configuration ------------------------ ---- before setting priority for links ------------ ---- before fixup boot-disabled links ------------- ---- after fixup boot-disabled links -------------- ---- arbitrated configuration --------------------- pci0: <ACPI PCI bus> on pcib0 pci0: physical bus=0 map[10]: type 3, range 32, base fe800000, size 22, enabled found-> vendor=0x8086, dev=0x2578, revid=0x02 bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0106, statreg=0x2090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x257b, revid=0x02 bus=0, slot=3, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0007, statreg=0x00a0, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x25ae, revid=0x02 bus=0, slot=28, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0146, statreg=0x0030, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x07 (1750 ns), maxlat=0x00 (0 ns) map[20]: type 4, range 32, base 0000e800, size 5, enabled pcib0: matched entry for 0.29.INTA (source ) pcib0: device is hardwired to IRQ 16 found-> vendor=0x8086, dev=0x25a9, revid=0x02 bus=0, slot=29, func=0 class=0c-03-00, hdrtype=0x00, mfdev=1 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=16 map[20]: type 4, range 32, base 0000ec00, size 5, enabled pcib0: matched entry for 0.29.INTB (source ) pcib0: device is hardwired to IRQ 19 found-> vendor=0x8086, dev=0x25aa, revid=0x02 bus=0, slot=29, func=1 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=19 map[10]: type 1, range 32, base fe7ff800, size 4, enabled found-> vendor=0x8086, dev=0x25ab, revid=0x02 bus=0, slot=29, func=4 class=08-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0002, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x25ac, revid=0x02 bus=0, slot=29, func=5 class=08-00-20, hdrtype=0x00, mfdev=0 cmdreg=0x0146, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type 1, range 32, base fe7ffc00, size 10, enabled pcib0: matched entry for 0.29.INTD (source ) pcib0: device is hardwired to IRQ 23 found-> vendor=0x8086, dev=0x25ad, revid=0x02 bus=0, slot=29, func=7 class=0c-03-20, hdrtype=0x00, mfdev=0 cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=d, irq=23 powerspec 2 supports D0 D3 current D0 found-> vendor=0x8086, dev=0x244e, revid=0x0a bus=0, slot=30, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0147, statreg=0x0080, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x0b (2750 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x25a1, revid=0x02 bus=0, slot=31, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x010f, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type 4, range 32, base 00000000, size 3, enabled map[14]: type 4, range 32, base 00000000, size 2, enabled map[18]: type 4, range 32, base 00000000, size 3, enabled map[1c]: type 4, range 32, base 00000000, size 2, enabled map[20]: type 4, range 32, base 0000fc00, size 4, enabled found-> vendor=0x8086, dev=0x25a2, revid=0x02 bus=0, slot=31, func=1 class=01-01-8a, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0288, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 map[10]: type 4, range 32, base 0000e400, size 3, enabled map[14]: type 4, range 32, base 0000e000, size 2, enabled map[18]: type 4, range 32, base 0000dc00, size 3, enabled map[1c]: type 4, range 32, base 0000d800, size 2, enabled map[20]: type 4, range 32, base 0000d400, size 4, enabled pcib0: matched entry for 0.31.INTA (source ) pcib0: device is hardwired to IRQ 18 found-> vendor=0x8086, dev=0x25b0, revid=0x02 bus=0, slot=31, func=2 class=01-04-8f, hdrtype=0x00, mfdev=0 cmdreg=0x0445, statreg=0x02a0, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=18 map[20]: type 4, range 32, base 00000400, size 5, enabled pcib0: matched entry for 0.31.INTB (source ) pcib0: device is hardwired to IRQ 17 found-> vendor=0x8086, dev=0x25a4, revid=0x02 bus=0, slot=31, func=3 class=0c-05-00, hdrtype=0x00, mfdev=0 cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=17 pcibios: No call entry point pcib1: <ACPI PCI-PCI bridge> at device 3.0 on pci0 pcib1: secondary bus 1 pcib1: subordinate bus 1 pcib1: I/O decode 0xb000-0xbfff pcib1: memory decode 0xfc500000-0xfc5fffff pcib1: prefetched decode 0xfff00000-0xfffff pcib1: could not get PCI interrupt routing table for \_SB_.PCI0.P0P2 - AE_NOT_FOUN D pci1: <ACPI PCI bus> on pcib1 pci1: physical bus=1 map[10]: type 1, range 32, base fc5e0000, size 17, enabled map[18]: type 4, range 32, base 0000bc00, size 5, enabled found-> vendor=0x8086, dev=0x1075, revid=0x00 bus=1, slot=1, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0238, cachelnsz=8 (dwords) lattimer=0x00 (0 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns) intpin=a, irq=9 powerspec 2 supports D0 D3 current D0 em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.19> port 0xbc00-0xbc1f m em 0xfc5e0000-0xfc5fffff irq 9 at device 1.0 on pci1 pcib1: device em0 requested decoded memory range 0xfc5e0000-0xfc5fffff pcib1: device em0 requested decoded I/O range 0xbc00-0xbc1f em0: bpf attached em0: Speed:N/A Duplex:N/A pcibios: No call entry point pcib2: <ACPI PCI-PCI bridge> at device 28.0 on pci0 pcib2: secondary bus 2 pcib2: subordinate bus 2 pcib2: I/O decode 0x0-0x0 pcib2: memory decode 0xfff00000-0xfffff pcib2: prefetched decode 0xfff00000-0xfffff ---- initial configuration ------------------------ ---- before setting priority for links ------------ ---- before fixup boot-disabled links ------------- ---- after fixup boot-disabled links -------------- ---- arbitrated configuration --------------------- pci2: <ACPI PCI bus> on pcib2 pci2: physical bus=2 uhci0: <UHCI (generic) USB controller> port 0xe800-0xe81f irq 16 at device 29.0 on pci0 usb0: <UHCI (generic) USB controller> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: <UHCI (generic) USB controller> port 0xec00-0xec1f irq 19 at device 29.1 on pci0 usb1: <UHCI (generic) USB controller> on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered pci0: <base peripheral> at device 29.4 (no driver attached) pci0: <base peripheral, interrupt controller> at device 29.5 (no driver attached) pci0: <serial bus, USB> at device 29.7 (no driver attached) pcibios: No call entry point pcib3: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pcib3: secondary bus 3 pcib3: subordinate bus 3 pcib3: I/O decode 0xc000-0xcfff pcib3: memory decode 0xfc600000-0xfe6fffff pcib3: prefetched decode 0xfff00000-0xfffff ---- initial configuration ------------------------ ---- before setting priority for links ------------ ---- before fixup boot-disabled links ------------- ---- after fixup boot-disabled links -------------- ---- arbitrated configuration --------------------- pci3: <ACPI PCI bus> on pcib3 pci3: physical bus=3 map[10]: type 1, range 32, base fd000000, size 24, enabled map[14]: type 4, range 32, base 0000c800, size 8, enabled map[18]: type 1, range 32, base fe6ff000, size 12, enabled pcib3: matched entry for 3.0.INTA (source ) pcib3: device is hardwired to IRQ 21 found-> vendor=0x1002, dev=0x4752, revid=0x27 bus=3, slot=0, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0087, statreg=0x0290, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns) intpin=a, irq=21 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base fe6fe000, size 12, enabled map[14]: type 4, range 32, base 0000cc00, size 6, enabled map[18]: type 1, range 32, base fe6a0000, size 17, enabled pcib3: matched entry for 3.1.INTA (source ) pcib3: device is hardwired to IRQ 17 found-> vendor=0x8086, dev=0x1229, revid=0x10 bus=3, slot=1, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0157, statreg=0x0290, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns) intpin=a, irq=17 powerspec 2 supports D0 D1 D2 D3 current D0 pci3: <display, VGA> at device 0.0 (no driver attached) fxp0: <Intel 82551 Pro/100 Ethernet> port 0xcc00-0xcc3f mem 0xfe6a0000-0xfe6bffff, 0xfe6fe000-0xfe6fefff irq 17 at device 1.0 on pci3 pcib3: device fxp0 requested decoded memory range 0xfe6fe000-0xfe6fefff fxp0: using memory space register mapping fxp0: Ethernet address 00:02:b3:e9:8e:8d fxp0: PCI IDs: 8086 1229 8086 342f 0010 fxp0: Dynamic Standby mode is disabled miibus0: <MII bus> on fxp0 inphy0: <i82555 10/100 media interface> on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp0: bpf attached isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <GENERIC ATA controller> port 0xfc00-0xfc0f,0-0x3,0-0x7,0-0x3,0-0x7 at de vice 31.1 on pci0 ata0: reset tp1 mask=03 ostat0=50 ostat1=00 ata0-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb ata0-slave: stat=0x00 err=0x00 lsb=0x00 msb=0x00 ata0: reset tp2 mask=03 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER> ata0: at 0x1f0 irq 14 on atapci0 ata0: [MPSAFE] ata1: reset tp1 mask=03 ostat0=00 ostat1=00 ata1-master: stat=0x01 err=0x01 lsb=0x01 msb=0x01 ata1-slave: stat=0x01 err=0x01 lsb=0x01 msb=0x01 ata1: reset tp2 mask=03 stat0=01 stat1=01 devices=0x0 ata1: at 0x170 irq 15 on atapci0 ata1: [MPSAFE] pci0: <mass storage, RAID> at device 31.2 (no driver attached) pci0: <serial bus, SMBus> at device 31.3 (no driver attached) acpi_button0: <Power Button> on acpi0 acpi_button1: <Sleep Button> on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0065 atkbd: keyboard ID 0x41ab (2) kbdc: RESET_KBD return code:00fa kbdc: RESET_KBD status:00aa kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000 psm0: unable to allocate IRQ psmcpnp0 irq 12 on acpi0 psm0: current command byte:0065 kbdc: TEST_AUX_PORT status:0000 kbdc: RESET_AUX return code:00fe kbdc: RESET_AUX return code:00fe kbdc: RESET_AUX return code:00fe kbdc: DIAGNOSE status:0055 kbdc: TEST_KBD_PORT status:0000 psm0: failed to reset the aux device. sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: irq maps: 0 0 0 0 sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A, console sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled sio1: irq maps: 0 0 0 0 sio1 port 0x2f8-0x2ff irq 3 on acpi0 sio1: type 16550A fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3 f5 irq 6 drq 2 on acpi0 fdc0: FIFO enabled, 8 bytes threshold ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it atkbdc: atkbdc0 already exists; skipping it fdc: fdc0 already exists; skipping it sio: sio0 already exists; skipping it sio: sio1 already exists; skipping it Trying Read_Port at 203 Trying Read_Port at 243 Trying Read_Port at 283 Trying Read_Port at 2c3 Trying Read_Port at 303 Trying Read_Port at 343 Trying Read_Port at 383 Trying Read_Port at 3c3 ex_isa_identify() sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices orm0: <Option ROMs> at iomem 0xdc000-0xdffff,0xc8000-0xcbfff,0xc0000-0xc7fff on is a0 pmtimer0 on isa0 adv0: not probed (disabled) aha0: not probed (disabled) aic0: not probed (disabled) bt0: not probed (disabled) cs0: not probed (disabled) ed0: not probed (disabled) fe0: not probed (disabled) ie0: not probed (disabled) le0: not probed (disabled) lnc0: not probed (disabled) pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0 pcic1: not probed (disabled) ppc0: parallel port not found. ppc0: <Parallel port> failed to probe at irq 7 on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) sio2: not probed (disabled) sio3: not probed (disabled) sn0: not probed (disabled) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 fb0: vga0, vga, type:VGA (5), flags:0x7007f fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 fb0: init mode:24, bios mode:3, current mode:24 fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k VGA parameters upon power-up 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters in BIOS for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff EGA/VGA parameters to be used for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff vt0: not probed (disabled) isa_probe_children: probing PnP devices Device configuration finished. procfs registered Timecounter "TSC" frequency 3192008572 Hz quality -100 Timecounters tick every 10.000 msec lo0: bpf attached md0: Preloaded image </boot/mfsroot> 4423680 bytes at 0xc09e16d8 acpi_cpu0: set speed to 100.0% acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0% ata0-master: pio=0x0c wdma=0x22 udma=0x42 cable=40pin GEOM: Configure md0a, start 0 length 4423680 end 4423679 GEOM: Configure md0c, start 0 length 4423680 end 4423679 [0] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:80 typ:165 s(CHS):0/0/1 e(CHS):1023/254/63 s:0 l:50000 [0] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:80 typ:165 s(CHS):0/0/1 e(CHS):1023/254/63 s:0 l:50000 acd0: <CREATIVEDVD1240E/3X14> DVDROM drive at ata0 as master acd0: read 6875KB/s (6875KB/s), 512KB buffer, PIO4 acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, packet acd0: Writes: acd0: Audio: play, 255 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: CD-ROM 120mm data disc SMP: AP CPU #1 Launched! cpu1 AP: ID: 0x01000000 VER: 0x00050014 LDR: 0x02000000 DFR: 0x0fffffff lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000000 SVR: 0x000001ff ioapic0: routing intpin 1 (IRQ 1) to cluster 0 ioapic0: routing intpin 3 (IRQ 3) to cluster 0 ioapic0: routing intpin 4 (IRQ 4) to cluster 0 ioapic0: routing intpin 6 (IRQ 6) to cluster 0 ioapic0: routing intpin 8 (IRQ 8) to cluster 0 ioapic0: routing intpin 9 (IRQ 9) to cluster 0 ioapic0: routing intpin 10 (IRQ 10) to cluster 0 ioapic0: routing intpin 13 (IRQ 13) to cluster 0 ioapic0: routing intpin 14 (IRQ 14) to cluster 0 ioapic0: routing intpin 15 (IRQ 15) to cluster 0 ioapic0: routing intpin 16 (IRQ 16) to cluster 0 ioapic0: routing intpin 17 (IRQ 17) to cluster 0 ioapic0: routing intpin 19 (IRQ 19) to cluster 0 Mounting root from ufs:/dev/md0 start_init: trying /sbin/init start_init: trying /sbin/oinit start_init: trying /sbin/init.bak start_init: trying /stand/sysinstall /stand/sysinstall running as init on serial console These are the predefined terminal types available to sysinstall when running stand-alone. Please choose the closest match for your particular terminal. 1 ...................... Standard ANSI terminal. 2 ...................... VT100 or compatible terminal. 3 ...................... FreeBSD system console (color). 4 ...................... FreeBSD system console (monochrome). 5 ...................... xterm terminal emulator. Your choice: (1-5) <snip>Sysinstall starts, following error occurs: No disks found! Please verify that your disk controller is being | properly probed at boot time. See the Hardware Guide on the Documentation menu for clues on diagnosing this type of problem. </snip> If you read this far, thank you... -- Feargal Reilly, Codeshifter, Chrysalink Systems. ICQ: 109837009 | YIM: ectoraige PGP Key ID: 0xA6F82C96 (expires 09-Jun-2005) Visit http://ie.bsd.net/ - BSDs presence in Ireland --Multipart=_Fri__16_Jul_2004_19_16_00_+0100_0ALERQe1tlRtbN5Z Content-Type: text/plain; name="4.10-PATA+SATA.log" Content-Disposition: attachment; filename="4.10-PATA+SATA.log" Content-Transfer-Encoding: 7bit Serial Redir 2.0.5 [VT-100+] BIOS LAN Console 4.0 Copyright (C) 1997-2002 Intel Corporation AMIBIOS(C)2003 American Megatrends, Inc. BIOS Date: 12/25/03 13:42:43 Ver: 08.00.10 SE7210TP10 Production BIOS Version 01.00, Build 0023 CPU : Intel(R) Pentium(R) 4 CPU 3.20GHz Speed : 3.20 GHz Press <F2> to run Setup Press <F12> for Network Boot Press <ESC> for BBS POPUP DDR Frequency 400 Mhz, Dual-Channel Checking NVRAM.. Initializing USB Controllers .. Done. Testing system memory, memory size=1024MB 1024MB Extended Memory Passed (C)AmericanMegatrends,Inc. 64-0100-000023-00101111-122503-CANTWOOD-STP1A023-Y2KC System Event Log Full Auto-Detecting Pri Master..ATAPI CDROM Auto-Detecting 3rd Master..IDE Hard Disk Auto-Detecting 4th Master..IDE Hard Disk Pri Master: CREATIVEDVD1240E 3X14 Ultra DMA Mode-2 3rd Master: ST380013AS 3.18 Ultra DMA Mode-5, S.M.A.R.T. Capable and Status OK 4th Master: ST380013AS 3.18 Ultra DMA Mode-5, S.M.A.R.T. Capable and Status OK Auto-detecting USB Mass Storage Devices .. 00 USB mass storage devices found and configured. +===========================================================================+ | Main Processor(s): Intel(R) Pentium(R) 4 CPU 3.20GHz | +===========================================================================+ | Math Processor : Built-In Base Memory Size : 640KB | | Floppy Drive A: : 1.44 MB 3@" Extd Memory Size : 1023MB | | Serial Port(s) : 3F8,2F8 Display Type : VGA/EGA | | BIOS Build Date : 12/25/03 PS/2 Mouse : None | | ACPI 1.0 Support : Enabled | +===========================================================================+ | ATA(PI) Device(s) Type Size LBA Block SMART 32Bit DMA PIO | | Mode Mode Info Mode Mode Mode| | Third Master : Hard Disk 80.0GB LBA 16Sec Good Off UDMA5 4 | | Fourth Master : Hard Disk 80.0GB LBA 16Sec Good Off UDMA5 4 | | Primary Master : ATAPI CDROM UDMA2 4 | +===========================================================================+ | PCI Devices: | | PCI Onboard PCI Bridge PCI Onboard PCI Bridge | | PCI Onboard USB Controller,IRQ9 PCI Onboard System Device | | PCI Onboard System Device PCI Onboard USB Controller,IRQ5 | | PCI Onboard USB Controller,IRQ7 PCI Onboard PCI Bridge | | PCI Onboard SerialBus Cntlr,IRQ5 PCI Onboard IDE,IRQ5 | | PCI Onboard IDE PCI Bridge Ethernet,IRQ5 | | PCI Bridge VGA,IRQ11 PCI Bridge Ethernet,IRQ5 | +===========================================================================+ Press <ESC> to boot....1 Uncompressing ... done BTX loader 1.00 BTX version is 1.01 Console: internal video/keyboard BIOS drive A: is disk0 BIOS drive B: is disk1 BIOS drive C: is disk2 BIOS drive D: is disk3 BIOS 579kB/1047488kB available memory FreeBSD/i386 bootstrap loader, Revision 0.8 (root@perseus.cse.buffalo.edu, Tue May 25 21:22:31 GMT 2004) /kernel text=0x28b691 data=0x3006c+0x32cc8 \ - Hit [Enter] to boot immediately, or any other key for command prompt. Type '?' for a list of commands, 'help' for more detailed help. ok boot -D -h -v SMAP type=01 base=0000000000000000 len=0000000000090c00 SMAP type=02 base=0000000000090c00 len=000000000000f400 SMAP type=02 base=00000000000e0000 len=0000000000020000 SMAP type=01 base=0000000000100000 len=000000003fef0000 SMAP type=03 base=000000003fff0000 len=000000000000f000 SMAP type=04 base=000000003ffff000 len=0000000000001000 SMAP type=02 base=00000000ffb00000 len=0000000000500000 Copyright (c) 1992-2004 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 Copyright (c) 1992-2004 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.10-RELEASE #0: Tue May 25 22:52:21 GMT 2004 root@perseus.cse.buffalo.edu:/usr/obj/usr/src/sys/BOOTMFS Calibrating clock(s) ... TSC clock: 3191799576 Hz, i8254 clock: 1193107 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz CLK_USE_TSC_CALIBRATION not specified - using old calibration method Timecounter "TSC" frequency 3192010216 Hz CPU: Intel(R) Pentium(R) 4 CPU 3.20GHz (3192.01-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf29 Stepping = 9 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,C MOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Hyperthreading: 2 logical CPUs real memory = 1073676288 (1048512K bytes) Physical memory chunk(s): 0x000001000 - 0x00008ffff, 585728 bytes (143 pages) 0x000850000 - 0x03ffe7fff, 1064927232 bytes (259992 pages) config> intro <snip>Kernel Configuration Menu, there were no conflicts so skipped it</snip> avail memory = 1037336576 (1013024K bytes) pnpbios: Found PnP BIOS data at 0xc00f4f30 pnpbios: Entry = f0000:5c34 Rev = 1.0 Other BIOS signatures found: ACPI: 000f7610 Preloaded elf kernel "kernel" at 0xc0829000. Preloaded mfs_root "/mfsroot" at 0xc0829098. Warning: Pentium 4 CPU: PSE disabled Pentium Pro MTRR support enabled md0: Preloaded image </mfsroot> 4423680 bytes at 0xc03ef3d4 Creating DISK md0 Creating DISK md1 md1: Malloc disk Math emulator present pci_open(1): mode 1 addr port (0x0cf8) is 0x80000090 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=25788086) pcibios: No call entry point npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <Host to PCI bridge> on motherboard found-> vendor=0x8086, dev=0x2578, revid=0x02 class=06-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 map[10]: type 1, range 32, base fe800000, size 22 found-> vendor=0x8086, dev=0x257b, revid=0x02 class=06-04-00, hdrtype=0x01, mfdev=0 subordinatebus=1 secondarybus=1 found-> vendor=0x8086, dev=0x25ae, revid=0x02 class=06-04-00, hdrtype=0x01, mfdev=0 subordinatebus=2 secondarybus=2 found-> vendor=0x8086, dev=0x25a9, revid=0x02 class=0c-03-00, hdrtype=0x00, mfdev=1 subordinatebus=0 secondarybus=0 intpin=a, irq=7 map[20]: type 1, range 32, base 0000e800, size 5 found-> vendor=0x8086, dev=0x25aa, revid=0x02 class=0c-03-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=b, irq=5 map[20]: type 1, range 32, base 0000ec00, size 5 found-> vendor=0x8086, dev=0x25ab, revid=0x02 class=08-80-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 map[10]: type 1, range 32, base fe7ff800, size 4 found-> vendor=0x8086, dev=0x25ac, revid=0x02 class=08-00-20, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 found-> vendor=0x8086, dev=0x25ad, revid=0x02 class=0c-03-20, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=d, irq=9 map[10]: type 1, range 32, base fe7ffc00, size 10 found-> vendor=0x8086, dev=0x244e, revid=0x0a class=06-04-00, hdrtype=0x01, mfdev=0 subordinatebus=3 secondarybus=3 found-> vendor=0x8086, dev=0x25a1, revid=0x02 class=06-01-00, hdrtype=0x00, mfdev=1 subordinatebus=0 secondarybus=0 found-> vendor=0x8086, dev=0x25a2, revid=0x02 class=01-01-8a, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=0 map[10]: type 1, range 32, base 00000000, size 3 map[14]: type 1, range 32, base 00000000, size 2 map[18]: type 1, range 32, base 00000000, size 3 map[1c]: type 1, range 32, base 00000000, size 2 map[20]: type 1, range 32, base 0000fc00, size 4 found-> vendor=0x8086, dev=0x25a3, revid=0x02 class=01-01-8f, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=5 map[10]: type 1, range 32, base 0000e400, size 3 map[14]: type 1, range 32, base 0000e000, size 2 map[18]: type 1, range 32, base 0000dc00, size 3 map[1c]: type 1, range 32, base 0000d800, size 2 map[20]: type 1, range 32, base 0000d400, size 4 found-> vendor=0x8086, dev=0x25a4, revid=0x02 class=0c-05-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=b, irq=5 map[20]: type 1, range 32, base 00000400, size 5 pci0: <PCI bus> on pcib0 pcib1: <PCI to PCI bridge (vendor=8086 device=257b)> at device 3.0 on pci0 found-> vendor=0x8086, dev=0x1075, revid=0x00 class=02-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=5 map[10]: type 1, range 32, base fc5e0000, size 17 map[18]: type 1, range 32, base 0000bc00, size 5 pci1: <PCI bus> on pcib1 pci1: <unknown card> (vendor=0x8086, dev=0x1075) at 1.0 irq 5 pcib2: <PCI to PCI bridge (vendor=8086 device=25ae)> at device 28.0 on pci0 pci2: <PCI bus> on pcib2 uhci0: <UHCI (generic) USB controller> port 0xe800-0xe81f irq 7 at device 29.0 on0 usb0: <UHCI (generic) USB controller> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: <UHCI (generic) USB controller> port 0xec00-0xec1f irq 5 at device 29.1 on0 usb1: <UHCI (generic) USB controller> on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered pci0: <unknown card> (vendor=0x8086, dev=0x25ab) at 29.4 pci0: <unknown card> (vendor=0x8086, dev=0x25ac) at 29.5 pci0: <USB controller> (vendor=0x8086, dev=0x25ad) at 29.7 irq 9 pcib3: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on pci0 found-> vendor=0x1002, dev=0x4752, revid=0x27 class=03-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=11 map[10]: type 1, range 32, base fd000000, size 24 map[14]: type 1, range 32, base 0000c800, size 8 map[18]: type 1, range 32, base fe6ff000, size 12 found-> vendor=0x8086, dev=0x1229, revid=0x10 class=02-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=5 map[10]: type 1, range 32, base fe6fe000, size 12 map[14]: type 1, range 32, base 0000cc00, size 6 map[18]: type 1, range 32, base fe6a0000, size 17 pci3: <PCI bus> on pcib3 pci3: <ATI Mach64-GR graphics accelerator> (vendor=0x1002, dev=0x4752) at 0.0 irq1 fxp0: <Intel 82551 Pro/100 Ethernet> port 0xcc00-0xcc3f mem 0xfe6a0000-0xfe6bffff3 fxp0: using memory space register mapping using shared irq5. fxp0: Ethernet address 00:02:b3:e9:8e:8d fxp0: PCI IDs: 8086 1229 8086 342f 0010 fxp0: Dynamic Standby mode is disabled inphy0: <i82555 10/100 media interface> on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto bpf: fxp0 attached isab0: <PCI to ISA bridge (vendor=8086 device=25a1)> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Generic PCI ATA controller> port 0xfc00-0xfc0f,0-0x3,0-0x7,0-0x3,0-0x7 0 ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xfc00 ata0: mask=03 ostat0=50 ostat2=00 ata0-master: ATAPI 14 eb ata0-slave: ATAPI 00 00 ata0: mask=03 stat0=00 stat1=00 ata0: devices=04 ata0: at 0x1f0 irq 14 on atapci0 ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xfc08 ata1: mask=03 ostat0=00 ostat2=00 ata1-master: ATAPI 74 74 ata1-slave: ATAPI 74 74 ata1: mask=03 stat0=74 stat1=74 ata1: devices=00 ata1: at 0x170 irq 15 on atapci0 atapci1: <Generic PCI ATA controller> port 0xd400-0xd40f,0xd800-0xd803,0xdc00-0xd0 ata-: ata2 exists, using next available unit number ata2: iobase=0xe400 altiobase=0xe002 bmaddr=0xd400 ata2: mask=03 ostat0=50 ostat2=00 ata2-slave: ATAPI c5 fa ata2-master: ATAPI 00 00 ata2: mask=03 stat0=50 stat1=00 ata2-master: ATA 01 a5 ata2: devices=01 ata2: at 0xe400 on atapci1 ata3: iobase=0xdc00 altiobase=0xd802 bmaddr=0xd408 ata3: mask=03 ostat0=50 ostat2=00 ata3-slave: ATAPI c5 fa ata3-master: ATAPI 00 00 ata3: mask=03 stat0=50 stat1=00 ata3-master: ATA 01 a5 ata3: devices=01 ata3: at 0xdc00 on atapci1 pci0: <unknown card> (vendor=0x8086, dev=0x25a4) at 31.3 irq 5 ex_isa_identify() ata-: ata0 exists, using next available unit number ata-: ata1 exists, using next available unit number Trying Read_Port at 203 Trying Read_Port at 243 Trying Read_Port at 283 Trying Read_Port at 2c3 Trying Read_Port at 303 Trying Read_Port at 343 Trying Read_Port at 383 Trying Read_Port at 3c3 isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xdc000-0xdffff on isa0 pmtimer0 on isa0 fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold ata4 failed to probe at port 0x1f0 irq 14 on isa0 ata5 failed to probe at port 0x170 irq 15 on isa0 adv0 failed to probe on isa0 bt0: Failed Status Reg Test - ff bt_isa_probe: Probe failed at 0x330 bt0: Failed Status Reg Test - ff bt_isa_probe: Probe failed at 0x334 bt0: Failed Status Reg Test - ff bt_isa_probe: Probe failed at 0x230 bt0: Failed Status Reg Test - ff bt_isa_probe: Probe failed at 0x234 bt0: Failed Status Reg Test - ff bt_isa_probe: Probe failed at 0x130 bt0: Failed Status Reg Test - ff bt_isa_probe: Probe failed at 0x134 bt0 failed to probe at port 0x134-0x137 on isa0 aha0: status reg test failed ff aha0: status reg test failed ff aha0: status reg test failed ff aha0: status reg test failed ff aha0: status reg test failed ff aha0: status reg test failed ff aha0 failed to probe at port 0x134-0x137 on isa0 aic0 failed to probe at port 0x140-0x15f on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0065 atkbd: keyboard ID 0x41ab (2) kbdc: RESET_KBD return code:00fa kbdc: RESET_KBD status:00aa kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000 psm0: current command byte:0065 kbdc: TEST_AUX_PORT status:0000 kbdc: RESET_AUX return code:00fe kbdc: RESET_AUX return code:00fe kbdc: RESET_AUX return code:00fe kbdc: DIAGNOSE status:0055 kbdc: TEST_KBD_PORT status:0000 psm0: failed to reset the aux device. vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 fb0: vga0, vga, type:VGA (5), flags:0x7007f fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 fb0: init mode:24, bios mode:3, current mode:24 fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k VGA parameters upon power-up 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 06 90 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters in BIOS for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff EGA/VGA parameters to be used for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x100> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0 pcic1: not probed (disabled) sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: irq maps: 0 0 0 0 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A, console sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: irq maps: 0 0 0 0 sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A sio2: not probed (disabled) sio3: not probed (disabled) ppc0: parallel port not found. ppc0: <Parallel port> failed to probe at irq 7 on isa0 ed0: not probed (disabled) fe0: not probed (disabled) ie0: not probed (disabled) lnc0: not probed (disabled) cs0: not probed (disabled) sn0: not probed (disabled) isa_probe_children: probing PnP devices BIOS Geometries: 0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors 1:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors 0 accounted for Device configuration finished. bpf: lo0 attached bpf: sl0 attached --Multipart=_Fri__16_Jul_2004_19_16_00_+0100_0ALERQe1tlRtbN5Z-- --Signature=_Fri__16_Jul_2004_19_16_00_+0100_HTskwW.lMrmAf9fy Content-Type: application/pgp-signature -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.4 (FreeBSD) iD8DBQFA+BthorFlI6b4LJYRAmwkAJ0W74EpOGdBgCZh7wu875Xw4DG8IgCfXgTq 8Aed4o0oFIOky6lq1VIH5XA= =636f -----END PGP SIGNATURE----- --Signature=_Fri__16_Jul_2004_19_16_00_+0100_HTskwW.lMrmAf9fy--
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20040716191600.282c3dc9>