Date: Thu, 28 Nov 1996 15:32:36 -0500 (EST) From: Yun-Ching Lee <ycl+@CMU.EDU> To: current@freebsd.org Subject: 2.2-ALPHA kills AHA 2940AU BIOS Message-ID: <UmbTPYy00YUz044140@andrew.cmu.edu>
next in thread | raw e-mail | index | archive | help
I just got 2.2-ALPHA installed on my system, a IBM 6x86 133/P166+. The
2.2-ALPHA generic kernel starts fine, but when I want to reboot, the
Adaptec BIOS hangs when scanning the SCSI bus. However, the SCSIselect
utility sees both of my devices fine.
I'm going to fetch the latest 3.0-CURRENT kernel and try that.
Here's my kernel -v message:
Copyright (c) 1992-1996 FreeBSD Inc.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 2.2-ALPHA #0: Wed Nov 13 15:29:19 1996
jkh@time.cdrom.com:/usr/src/sys/compile/GENERIC
Calibrating clock(s) relative to mc146818A clock ... i8254 clock: 1193187 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
CPU: i486DX (486-class CPU)
real memory = 67108864 (65536K bytes)
avail memory = 62664704 (61196K bytes)
BIOS Geometries:
0:0107fe3f 0..263=264 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
pcibus_setup(1): mode 1 addr port (0x0cf8) is 0x8000005c
pcibus_setup(1a): mode1res=0x80000000 (0x80000000)
pcibus_check: device 0 is there (id=70308086)
Probing for devices on PCI bus 0:
configuration mode 1 allows 32 devices.
chip0 <generic PCI bridge (vendor=8086 device=7030 subclass=0)> rev 2 on pci0:0
chip1 <Intel 82371SB PCI-ISA bridge> rev 1 on pci0:7:0
chip2 <Intel 82371SB IDE interface> rev 0 on pci0:7:1
mapreg[20] type=1 addr=0000e800 size=0010.
vga0 <VGA-compatible display device> rev 3 on pci0:11
mapreg[10] type=0 addr=fa000000 size=1000000.
ahc0 <Adaptec 2940A Ultra SCSI host adapter> rev 1 int a irq 9 on pci0:12
mapreg[10] type=1 addr=0000e000 size=0100.
mapreg[14] type=0 addr=f9fff000 size=1000.
reg16: ioaddr=0xe000 size=0x100
ahc0: Reading SEEPROM...done.
ahc0: aic7860 Single Channel, SCSI Id=7, 3 SCBs
ahc0: Downloading Sequencer Program...Done
ahc0: Probing channel A
ahc0 waiting for scsi devices to settle
ahc0: target 0 synchronous at 10.0MHz, offset = 0xf
(ahc0:0:0): "FUJITSU M2915S-512 0127" type 0 fixed SCSI 2
sd0(ahc0:0:0): Direct-Access 2075MB (4250695 512 byte sectors)
sd0(ahc0:0:0): with 3011 cyls, 15 heads, and an average 94 sectors/track
ahc0:A:4: refuses syncronous negotiation. Using asyncronous transfers
(ahc0:4:0): "NEC CD-ROM DRIVE:210 1.0" type 5 removable SCSI 1
cd0(ahc0:4:0): CD-ROM cd present [192775 x 2048 byte records]
pci0: uses 16781312 bytes of memory from f9fff000 upto faffffff.
pci0: uses 272 bytes of I/O space from e000 upto e80f.
Probing for devices on the ISA bus:
sc0 at 0x60-0x6f irq 1 on motherboard
sc0: VGA color <16 virtual consoles, flags=0x0>
ed0 not found at 0x280
ed1 not found at 0x300
fe0 not found at 0x300
sio0 at 0x3f8-0x3ff irq 4 on isa
sio0: type 16550A
sio1 at 0x2f8-0x2ff irq 3 on isa
sio1: type 16550A
sio2: disabled, not probed.
sio3: disabled, not probed.
lpt0 at 0x378-0x37f irq 7 on isa
lpt0: Interrupt-driven port
lp0: TCP/IP capable interface
lpt1 at 0x378-0x37f on isa
lpt1 not probed due to I/O address conflict with lpt0 at 0x378
mse0: wrong signature ff
mse0 not found at 0x23c
psm0 at 0x60-0x63 irq 12 on motherboard
fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
fdc0: NEC 72065B
fd0: 1.44MB 3.5in
fd1: 1.2MB 5.25in
wdc0 not found at 0x1f0
wdc1 not found at 0x170
bt0 not found at 0x330
uha0 not found at 0x330
aha0 not found at 0x330
aic0 not found at 0x340
nca0 not found at 0x1f88
nca1 not found at 0x350
sea0 not found
wt0 not found at 0x300
mcd0: timeout getting status
mcd0 not found at 0x300
matcdc0 not found at 0x230
scd0 not found at 0x230
ie0 not found at 0x360
1 3C5x9 board(s) on ISA found at 0x300
ep0 at 0x300-0x30f irq 10 on isa
ep0: aui/utp/bnc[*UTP*] address 00:a0:24:89:71:42
ix0 not probed due to I/O address conflict with ep0 at 0x300
le0 not probed due to I/O address conflict with ep0 at 0x300
lnc0 not found at 0x280
ze0 not probed due to I/O address conflict with ep0 at 0x300
zp0 not probed due to I/O address conflict with ep0 at 0x300
npx0 on motherboard
npx0: INT 16 interface
apm0: disabled, not probed.
imasks: bio c0000240, tty c003149a, net c003149a
Device configuration finished.
Considering FFS root f/s.
changing root device to sd0a
configure() finished.
sd0s1: type 0xa5, start 63, end = 2184839, size 2184777 : OK
sd0s2: type 0x6, start 2184840, end = 4241159, size 2056320 : OK
--
Yun-Ching (Allen) Lee # "There is no such thing as a good influence...
ycl+@cmu.edu # All influence is immoral."
yunching+@andrew.cmu.edu # -- Lord Henry Wotton
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?UmbTPYy00YUz044140>