Date: Sun, 15 Oct 2000 18:10:36 -1000 From: "Kuriyama, Kent K Mr (CPF N651KK)" <KuriyaKK@cpf.navy.mil> To: "Freebsd-Stable (E-mail)" <freebsd-stable@FreeBSD.ORG> Subject: Screen saver error message seen on 4.1.1-STABLE Message-ID: <A567A7C3889FD2119D2600204840388C03E9EB91@uemspricpf3.cpf.navy.mil>
next in thread | raw e-mail | index | archive | help
On the CVSUP dated 10/10/00 I get the following error message:
logo_saver: no suitable graphics mode
module_register_init: MOD_LOAD (logo_saver, c0d48a60, 0) error 19
My rc.conf contains the line:
saver="logo"
These error messages did not occur in earlier snapshots of 4.1.1-STABLE.
Shown below is the 'dmesg' output, I created a GENERIC kernel to remove any
"customizations" as a reason for the problem. Any help would be greatly
appreciated. Thanks.
Kent Kuriyama
SPAWAR Sys Ctr San Diego D424, CINCPACFLT N671KK
kuriyakk@cpf.navy.mil, 808-471-4125
-----Original Message-----
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.1.1-STABLE #0: Sun Oct 15 17:29:14 HST 2000
root@somehost:/usr/src/sys/compile/GENERIC
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium Pro (199.43-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x617 Stepping = 7
Features=0xfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMO
V>
real memory = 67108864 (65536K bytes)
avail memory = 61190144 (59756K bytes)
Preloaded elf kernel "kernel" at 0xc041d000.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
Correcting Natoma config for non-SMP
Correcting Natoma config for non-SMP
isab0: <Intel 82371SB PCI to ISA bridge> at device 13.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX3 ATA controller> port 0xffa0-0xffaf at device 13.1 on
pci0
atapci0: Busmastering DMA not enabled
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pcib1: <DEC 21052 PCI-PCI bridge> at device 14.0 on pci0
pci1: <PCI bus> on pcib1
ahc0: <Adaptec 2940A Ultra SCSI adapter> port 0xdc00-0xdcff mem
0xf9fff000-0xf9ffffff irq 10 at device 11.0 on pci1
aic7860: Single Channel A, SCSI Id=7, 3/255 SCBs
pci0: <S3 Trio graphics accelerator> at 16.0 irq 0
xl0: <3Com 3c900-COMBO Etherlink XL> port 0xccc0-0xccff irq 11 at device
17.0 on pci0
xl0: Ethernet address: 00:60:97:61:83:aa
xl0: selecting 10baseT transceiver, half duplex
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
vga0: <Generic ISA VGA> at port 0x3b0-0x3cf iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA (mono) <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ad0: 3020MB <WDC AC33100H> [6136/16/63] at ata0-master using BIOSPIO
acd0: CDROM <NEC CD-ROM DRIVE:282> at ata1-master using PIO3
Waiting 15 seconds for SCSI devices to settle
Mounting root from ufs:/dev/ad0s1a
IP packet filtering initialized, divert disabled, rule-based forwarding
disabled, default to deny, logging disabled
logo_saver: no suitable graphics mode
module_register_init: MOD_LOAD (logo_saver, c0d48a60, 0) error 19
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?A567A7C3889FD2119D2600204840388C03E9EB91>