Date: 18 Jun 2002 11:33:08 -0400 From: Joe Marcus Clarke <marcus@marcuscom.com> To: Jamie Heckford <jamie@tridentmicrosystems.co.uk> Cc: freebsd-stable@FreeBSD.ORG Subject: Re: Wierd ATA errors Message-ID: <1024414388.313.2.camel@gyros.marcuscom.com> In-Reply-To: <083501c216da$a51566c0$4464a8c0@JAMIEHECKFORD> References: <083501c216da$a51566c0$4464a8c0@JAMIEHECKFORD>
next in thread | previous in thread | raw e-mail | index | archive | help
On Tue, 2002-06-18 at 11:13, Jamie Heckford wrote: > Hi, > > Im getting a lot of strange errors on FreeBSD 4.6-STABLE #2: Tue Jun 18 > 14:20:36 BST 2002, > involving 3x 120GB drives I have installed. > > The errors im getting are ones such as these: > > ad5: WRITE command timeout tag=0 serv=0 - resetting > ata2: resetting devices .. ad4: DMA limited to UDMA33, non-ATA66 cable or > device > done > ad6: WRITE command timeout tag=0 serv=0 - resetting > ata3: resetting devices .. done > ad6: WRITE command timeout tag=0 serv=0 - resetting > ata3: resetting devices .. done > > I haven't enabled tagged q'ing or write caching - full dmesg output with > errors attached. I recently bought a Maxtor 40 GB ATA 133 drive, and plugged it into an on-board Intel ATA 66 controller. I got the same errors from my drive. Then, I went out and bought a Maxtor ATA 133 controller, and I still get the same errors. This is all while installing 4.6-RELEASE. I have a working ATA 100 drive that works on both controllers. I've done all the listed workarounds for installing 4.6. I suspect bad hardware since I've tried different controllers, different cables, and different jumper settings. You may want to do a bit more troubleshooting, but you may come to the same conclusion. Joe > > Thanks in advance for any help, > > -- > Jamie Heckford > Network Manager > Trident Microsystems Ltd > Tel: 01737 780790 Fax: 01737 771908 > http://www.tridentmicrosystems.co.uk > > *********** > > This e-mail message contains confidential information for > the above addressee only. Any opinion or views contained > in this e-mail message are those of the sender and do not > necessarily represent those of the Company. Unless otherwise > stated this e-mail message is not intended to be contractually > binding. E-mail transmission cannot be guaranteed to be > secure or error-free and the sender therefore does not accept > liability for any errors or omissions in the contents of this > message. > > Trident Microsystems Ltd Group of Companies > Perrywood Business Park, Honeycrock Lane, Salfords, Redhill, > Surrey, RH1 5JQ > > Tel: (44) (0) 1737 780790 Fax: (44) (0) 1737 771908 > > Registered office: Abacus House, Bone Lane, Newbury, > Berkshire, RG14 5SF > ---- > > Copyright (c) 1992-2002 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 4.6-STABLE #2: Tue Jun 18 14:20:36 BST 2002 > admin@lennon.trident-uk.co.uk:/usr/src/sys/compile/LENNON > Timecounter "i8254" frequency 1193182 Hz > Timecounter "TSC" frequency 1263450917 Hz > CPU: Pentium III/Pentium III Xeon/Celeron (1263.45-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0x6b1 Stepping = 1 > Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> > real memory = 671072256 (655344K bytes) > avail memory = 649281536 (634064K bytes) > Preloaded elf kernel "kernel" at 0xc02e3000. > Pentium Pro MTRR support enabled > md0: Malloc disk > npx0: <math processor> on motherboard > npx0: INT 16 interface > pcib0: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard > pci0: <PCI bus> on pcib0 > atapci0: <CMD 649 ATA100 controller> port 0x2030-0x203f,0x2028-0x202b,0x2020-0x2027,0x2018-0x201b,0x2010-0x2017 irq 5 at devic > e 3.0 on pci0 > ata2: at 0x2010 on atapci0 > ata3: at 0x2020 on atapci0 > fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x2040-0x207f mem 0xc6e00000-0xc6efffff,0xc6fff000-0xc6ffffff irq 10 at device 4. > 0 on pci0 > fxp0: Ethernet address 00:02:a5:ed:e6:f4 > inphy0: <i82555 10/100 media interface> on miibus0 > inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > pci0: <ATI Mach64-GR graphics accelerator> at 5.0 irq 11 > pci0: <unknown card> (vendor=0x0e11, dev=0xa0f0) at 6.0 irq 15 > isab0: <PCI to ISA bridge (vendor=1166 device=0201)> at device 15.0 on pci0 > isa0: <ISA bus> on isab0 > atapci1: <ServerWorks CSB5 ATA100 controller> port 0xa00-0xa03,0x2000-0x200f,0-0x3,0-0x7,0x3f4-0x3f7,0x1f0-0x1f7 at device 15. > 1 on pci0 > ata0: at 0x1f0 irq 14 on atapci1 > ata1: at 0x170 irq 15 on atapci1 > pci0: <OHCI USB controller> at 15.2 irq 15 > pcib2: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard > pci2: <PCI bus> on pcib2 > pcib1: <Host to PCI bridge> on motherboard > pci1: <PCI bus> on pcib1 > eisa0: <EISA bus> on motherboard > mainboard0: <CPQ0721 (System Board)> on eisa0 slot 0 > orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xee000-0xeffff on isa0 > fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 > fdc0: FIFO enabled, 8 bytes threshold > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 > kbd0 at atkbd0 > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > IP packet filtering initialized, divert disabled, rule-based forwarding disabled, default to accept, logging limited to 100 pa > ckets/entry by default > ata0-slave: ATA identify retries exceeded > ad4: 38166MB <MAXTOR 6L040J2> [77545/16/63] at ata2-master UDMA100 > ad5: 114473MB <WDC WD1200JB-00CRA1> [232581/16/63] at ata2-slave UDMA100 > ad6: 114473MB <WDC WD1200JB-00CRA1> [232581/16/63] at ata3-master UDMA100 > ad7: 114473MB <WDC WD1200JB-00CRA1> [232581/16/63] at ata3-slave UDMA100 > acd0: CDROM <Compaq CRD-8402B> at ata0-master PIO4 > Mounting root from ufs:/dev/ad4s1a > stray irq 7 > stray irq 7 > stray irq 7 > stray irq 7 > stray irq 7 > too many stray irq 7's; not logging any more > vinum: loaded > vinum: CONFIGURATION OBLITERATED > vinum: drive vinumdrive0 is up > vinum: drive vinumdrive1 is up > vinum: drive vinumdrive2 is up > vinum: removing 363 blocks of partial stripe at the end of vinum0.p0 > vinum: vinum0.p0.s0 is up > vinum: vinum0.p0.s1 is up > vinum: vinum0.p0.s2 is up > vinum: vinum0.p0 is up > vinum: vinum0 is up > ad5: WRITE command timeout tag=0 serv=0 - resetting > ata2: resetting devices .. ad4: DMA limited to UDMA33, non-ATA66 cable or device > done > ad6: WRITE command timeout tag=0 serv=0 - resetting > ata3: resetting devices .. done > ad6: WRITE command timeout tag=0 serv=0 - resetting > ata3: resetting devices .. done > ad6: WRITE command timeout tag=0 serv=0 - resetting > ata3: resetting devices .. done > ad7: WRITE command timeout tag=0 serv=0 - resetting > ata3: resetting devices .. done > ad6: WRITE command timeout tag=0 serv=0 - resetting > ata3: resetting devices .. done > ad6: WRITE command timeout tag=0 serv=0 - resetting > ata3: resetting devices .. done > ad6: READ command timeout tag=0 serv=0 - resetting > ata3: resetting devices .. done > ad5: WRITE command timeout tag=0 serv=0 - resetting > ata2: resetting devices .. ad4: DMA limited to UDMA33, non-ATA66 cable or device > done > ad5: WRITE command timeout tag=0 serv=0 - resetting > ata2: resetting devices .. ad4: DMA limited to UDMA33, non-ATA66 cable or device > done > ad5: WRITE command timeout tag=0 serv=0 - resetting > ata2: resetting devices .. ad4: DMA limited to UDMA33, non-ATA66 cable or device > done > ad5: WRITE command timeout tag=0 serv=0 - resetting > ata2: resetting devices .. ad4: DMA limited to UDMA33, non-ATA66 cable or device > done > ad5: WRITE command timeout tag=0 serv=0 - resetting > ata2: resetting devices .. ad4: DMA limited to UDMA33, non-ATA66 cable or device > done > ad6: WRITE command timeout tag=0 serv=0 - resetting > ata3: resetting devices .. done > ad6: WRITE command timeout tag=0 serv=0 - resetting > ata3: resetting devices .. done > ad6: WRITE command timeout tag=0 serv=0 - resetting > ata3: resetting devices .. done > ad7: WRITE command timeout tag=0 serv=0 - resetting > ata3: resetting devices .. done > ad7: WRITE command timeout tag=0 serv=0 - resetting > ata3: resetting devices .. done > ad6: WRITE command timeout tag=0 serv=0 - resetting > ata3: resetting devices .. done > ad7: WRITE command timeout tag=0 serv=0 - resetting > ata3: resetting devices .. done > ad6: WRITE command timeout tag=0 serv=0 - resetting > ata3: resetting devices .. done > ad6: WRITE command timeout tag=0 serv=0 - resetting > ata3: resetting devices .. done -- PGP Key : http://www.marcuscom.com/pgp.asc To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1024414388.313.2.camel>