Skip site navigation (1)Skip section navigation (2)
Date:      Wed, 22 Dec 1999 17:15:44 -0600 (CST)
From:      "Eric J. Haug" <ejh@eas.slu.edu>
To:        current@freebsd.org
Cc:        ejh@ejhslu.eas.slu.edu
Subject:   Toshiba 2100CDS ata hangs and internal modem
Message-ID:  <199912222315.RAA21917@ejhslu.eas.slu.edu>

next in thread | raw e-mail | index | archive | help
Hi All,
This laptop has a couple of problems with FreeBSD-CURRENT
of about 1999/12/22 12:00 UTC.
The system hangs with the disk drive light on.
The output of boot -vc captured from the serial port follows.
current of about 1999/12/11 works in PIO mode.

The machine has a built-in modem that appears to be on the pci bus.
The sio1 probes fail.
If the modem is on the pci bus, what would it take to get it going?
I noted that sys/dev/sio was purged awhile ago. Has anyone worked on
pci serial/parallel stuff, like the SIIG cards? Should sys/dev/ed be
used as a model?

It also has a soundsystem and CardBus, but first things first.

eric haug
Saint Louis Univ.

avail memory = 29380608 (28692K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00f9000
bios32: Entry = 0xfe95a (c00fe95a)  Rev = 0  Len = 1
pcibios: PCI BIOS entry at 0xd1bc
pnpbios: Found PnP BIOS data at 0xc00f9040
pnpbios: Entry = f0000:9536  Rev = 1.0
pnpbios: Event flag at 510
pnpbios: OEM ID a934f351
Other BIOS signatures found:
ACPI: 000fe660
Preloaded elf kernel "kernel.lt" at 0xc02ff000.
md0: Malloc disk
Creating DISK md0
pci_open(1):    mode 1 addr port (0x0cf8) is 0x8000a050
pci_open(1a):   mode1res=0x80000000 (0x80000000)
pci_cfgcheck:   device 0 [class=060000] [hdr=00] is there (id=06181179)
npx0: <math processor> on motherboard
npx0: INT 16 interface
i586_bzero() bandwidth = 109757436 bytes/sec
bzero() bandwidth = 146092037 bytes/sec
apm0: <APM BIOS> on motherboard
apm: found APM BIOS v1.2, connected at v1.2
pci_open(1):    mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a):   mode1res=0x80000000 (0x80000000)
pci_cfgcheck:   device 0 [class=060000] [hdr=00] is there (id=06181179)
pcib0: <Host to PCI bridge> on motherboard
found-> vendor=0x1179, dev=0x0618, revid=0x02
        class=06-00-00, hdrtype=0x00, mfdev=0
        subordinatebus=0        secondarybus=0
found-> vendor=0x11c1, dev=0x0441, revid=0x01
        class=07-80-00, hdrtype=0x00, mfdev=0
        subordinatebus=0        secondarybus=0
        intpin=a, irq=3
        map[10]: type 1, range 32, base ffefff00, size  8
        map[14]: type 3, range 32, base 000002f8, size  3
        map[18]: type 1, range 32, base 00001c00, size  8
found-> vendor=0x5333, dev=0x8c01, revid=0x06
        class=03-00-00, hdrtype=0x00, mfdev=0
        subordinatebus=0        secondarybus=0
        map[10]: type 1, range 32, base f8000000, size 26
found-> vendor=0x1033, dev=0x0035, revid=0x02
        class=0c-03-10, hdrtype=0x00, mfdev=0
        subordinatebus=0        secondarybus=0
        intpin=a, irq=11
        map[10]: type 1, range 32, base f7fff000, size 12
found-> vendor=0x125d, dev=0x1978, revid=0x10
        class=04-01-00, hdrtype=0x00, mfdev=0
        subordinatebus=0        secondarybus=0
        intpin=a, irq=11
        map[10]: type 1, range 32, base 0000ff00, size  8
found-> vendor=0x1179, dev=0x0102, revid=0x34
        class=01-01-f0, hdrtype=0x00, mfdev=0
        subordinatebus=0        secondarybus=0
        map[20]: type 1, range 32, base 00001800, size  4
found-> vendor=0x1179, dev=0x060f, revid=0x07
        class=06-07-00, hdrtype=0x02, mfdev=1
        subordinatebus=14       secondarybus=14
        intpin=a, irq=255
found-> vendor=0x1179, dev=0x060f, revid=0x07
        class=06-07-00, hdrtype=0x02, mfdev=1
        subordinatebus=15       secondarybus=15
        intpin=b, irq=255
pci0: <PCI bus> on pcib0
pci0: unknown card (vendor=0x11c1, dev=0x0441) at 7.0 irq 3
vga-pci0: <S3 model 8c01 graphics accelerator> at device 8.0 on pci0
ohci0: <NEC uPD 9210 USB controller> irq 11 at device 11.0 on pci0
usb0: OHCI version 1.0
usb0: <NEC uPD 9210 USB controller> on ohci0
usb0: USB revision 1.0
uhub0: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: unknown card (vendor=0x125d, dev=0x1978) at 12.0 irq 11
ata-pci0: <Unknown PCI ATA controller (generic mode)> at device 16.0 on pci0
ata-pci0: Busmastering DMA supported
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x1800
ata0: mask=03 status0=50 status1=00
ata0: mask=03 status0=50 status1=00
ata0: devices = 0x1
ata0 at 0x01f0 irq 14 on ata-pci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x1808
ata1: mask=03 status0=50 status1=01
ata1: mask=03 status0=00 status1=01
ata1: devices = 0x4
ata1 at 0x0170 irq 15 on ata-pci0
pcic-pci0: <Toshiba ToPIC97 PCI-CardBus Bridge> at device 19.0 on pci0
PCI Config space:
00:  060f1179 04800007 06070007 00820000
10:  00000000 04800000 00141400 00000000
20:  00000000 00000000 00000000 00000000
30:  00000000 00000000 00000000 000001ff
40:  00011179 000003e1 00000000 00000000
50:  00000000 00000000 00000000 00000000
60:  00000000 00000000 00000000 00000000
70:  00000000 00000000 00000000 00000000
80:  00000000 00000000 00000000 01000000
90:  00000000 00000000 00000000 00000000
Cardbus Socket registers:
00:  f000ef6f: f000ef6f: f000e2c3: f000ef6f:
10:  f000ef6f: f000ff54: f000e140: f000ef6f:
ExCa registers:
00: 13 88 f5 5a 72 d0 80 e1 3f 74 c8 fa 66 8b 46 08
10: 52 66 0f b6 d9 66 31 d2 66 f7 f3 88 eb 88 d5 43
20: 30 d2 66 f7 f3 88 d7 5a 66 3d ff 03 00 00 fb 77
30: a2 86 c4 c0 c8 02 08 e8 40 91 88 fe 28 e0 8a 66
pcic-pci1: <Toshiba ToPIC97 PCI-CardBus Bridge> at device 19.1 on pci0
PCI Config space:
00:  060f1179 04800007 06070007 00820000
10:  00000000 04800000 00151500 00000000
20:  00000000 00000000 00000000 00000000
30:  00000000 00000000 00000000 000002ff
40:  00011179 000003e1 00000000 00000000
50:  00000000 00000000 00000000 00000000
60:  00000000 00000000 00000000 00000000
70:  00000000 00000000 00000000 00000000
80:  00000000 00000000 00000000 01000000
90:  00000000 00000000 00000000 00000000
Cardbus Socket registers:
00:  f000ef6f: f000ef6f: f000e2c3: f000ef6f:
10:  f000ef6f: f000ff54: f000e140: f000ef6f:
ExCa registers:
00: 13 88 f5 5a 72 d0 80 e1 3f 74 c8 fa 66 8b 46 08
10: 52 66 0f b6 d9 66 31 d2 66 f7 f3 88 eb 88 d5 43
20: 30 d2 66 f7 f3 88 d7 5a 66 3d ff 03 00 00 fb 77
30: a2 86 c4 c0 c8 02 08 e8 40 91 88 fe 28 e0 8a 66
isa0: <ISA bus> on motherboard
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f7 irq 6 drq 2 on isa0
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x1d0000
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model GlidePoint, device ID 0-00, 2 buttons
vga0: <Generic ISA VGA> at port 0x3b0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> on isa0
sc0: fb0 kbd0
pcic: polling, can't alloc 0
pcic: polling, can't alloc 0
pcic0: <Intel i82365> on isa0
pccard0: <PC Card bus -- kludge version> on pcic0
pccard1: <PC Card bus -- kludge version> on pcic0
sio0: irq maps: 0x41 0x51 0x51 0x51
sio0 at port 0x3f8-0x3ff irq 4 drq 0 flags 0x30 on isa0
sio0: type 16550A, console
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: irq maps: 0x41 0x41 0x41 0x41
sio1: probe failed test(s): 0 1 2 4
sio2: not probed (disabled)
sio3: not probed (disabled)
ppc: parallel port found at 0x378
ppc: chipset forced to generic
ppc0: SPP
ppc0 at port 0x378-0x37f irq 7 flags 0x40 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
plip: irq 7
plip0: <PLIP network interface> on ppbus 0
bpf: lp0 attached
lpt0: <generic printer> on ppbus 0
lpt0: Interrupt-driven port
ppi0: <generic parallel i/o> on ppbus 0
vpo0: can't connect to the drive
imm0: (disconnect) s1=0x38 s2=0x38, s3=0x38
imm0: (connect) s1=0x38 s2=0x38, s3=0x38
imm0: can't connect to the drive
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
isa_probe_children: probing PnP devices
BIOS Geometries:
 0:020cfe3f 0..524=525 cylinders, 0..254=255 heads, 1..63=63 sectors
 0 accounted for
Device configuration finished.
bpf: lo0 attached
ata0-master: success setting up WDMA2 mode on generic chip
ad0: piomode=4 dmamode=2 udmamode=2 cblid=0
ad0: <TOSHIBA MK4313MAT/J2.12 C> ATA-4 disk at ata0 as master
ad0: 4126MB (8452080 sectors), 8944 cyls, 15 heads, 63 S/T, 512 B/S
ad0: 16 secs/int, 1 depth queue, DMA
Creating DISK ad0
Creating DISK wd0
ata1-master: piomode=4 dmamode=2 udmamode=2 dmaflag=1
acd0: <CD-224E-B/7.6G> CDROM drive at ata1 as master
acd0: read 4134KB/s (4134KB/s), 128KB buffer, PIO
acd0: Reads: CD-R, CD-RW, CD-DA stream, packet
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray
acd0: Medium: no/blank disc inside, unlocked
Mounting root from ufs:/dev/ad0s2a
ad0: ad_timeout: lost disk contact - resetting
ata0: resetting devices .. ata0: mask=01 status0=50 status1=00



To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-current" in the body of the message




Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199912222315.RAA21917>