Date: Thu, 30 Apr 1998 20:54:01 +0200 (MET DST) From: Wilko Bulte <wilko@yedi.iaf.nl> To: freebsd-mobile@FreeBSD.ORG Subject: DEPCM ethernet refuses to work Message-ID: <199804301854.UAA25384@yedi.iaf.nl>
next in thread | raw e-mail | index | archive | help
Hi
I've been playing around with my DEPCM ethernet card in the 2.2.5R with
latest PAO patches. Sofar, no luck. The pccardd sees the card entering the
system, but then says: "device not configured". An Adaptec 1460 SCSI card
works OK in the same system so it looks like the problem is specific to the
DEPCM. Laptop is a DEC Hinote VP P120 with 40Mb DRAM.
Below is the dumpcis of the DEPCM, I hope that a knowledgeable person might
be able to see what causes the problem.
Configuration data for card in slot 1
Tuple #1, code = 0x1 (Common memory descriptor), length = 3
000: dc 03 ff
Common memory device information:
Device number 1, type Function specific, WPS = ON
Speed = 100nS, Memory block size = 32Kb, 1 units
Tuple #2, code = 0x17 (Attribute memory descriptor), length = 3
000: 53 01 ff
Attribute memory device information:
Device number 1, type FLASH EEPROM, WPS = OFF
Speed = 150nS, Memory block size = 2Kb, 1 units
Tuple #3, code = 0x21 (Functional ID), length = 2
000: 06 03
Network/LAN adapter - POST initialize - Card has ROM
Tuple #4, code = 0x15 (Version 1 info), length = 39
000: 04 01 44 49 47 49 54 41 4c 00 44 45 50 43 4d 2d
010: 58 58 00 31 39 39 34 30 35 33 31 00 41 30 31 2e
020: 30 30 2e 30 31 00 ff
Version = 4.1, Manuf = [DIGITAL],card vers = [DEPCM-XX]
Addit. info = [19940531],[A01.00.01]
Tuple #5, code = 0x1a (Configuration map), length = 5
000: 01 08 00 01 01
Reg len = 2, config register addr = 0x100, last config = 0x8
Registers: X-------
Tuple #6, code = 0x1b (Configuration entry), length = 21
000: c1 81 1d 3f 55 4d 5d 06 86 46 26 fc 24 ca 60 00
010: 03 1f 30 38 9e
Config index = 0x1(default)
Interface byte = 0x81 (I/O) wait signal supported
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Minimum operating supply voltage: 4.5 x 1V
Maximum operating supply voltage: 5.5 x 1V
Continuous supply current: 1 x 100mA
Max current average over 1 second: 1 x 100mA, ext = 0x46
Max current average over 10 ms: 2 x 100mA
Wait scale Speed = 1.5 x 10 us
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x300 block length = 0x20
IRQ modes: Level
IRQs: 3 4 5 9 10 11 12 15
Tuple #7, code = 0x1b (Configuration entry), length = 7
000: 02 08 ca 60 20 03 1f
Config index = 0x2
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x320 block length = 0x20
Tuple #8, code = 0x1b (Configuration entry), length = 7
000: 03 08 ca 60 40 03 1f
Config index = 0x3
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x340 block length = 0x20
Tuple #9, code = 0x1b (Configuration entry), length = 7
000: 04 08 ca 60 60 03 1f
Config index = 0x4
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x360 block length = 0x20
Tuple #10, code = 0x1b (Configuration entry), length = 7
000: 05 08 ca 60 00 02 1f
Config index = 0x5
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x200 block length = 0x20
Tuple #11, code = 0x1b (Configuration entry), length = 7
000: 06 08 ca 60 40 7f 1f
Config index = 0x6
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x7f40 block length = 0x20
Tuple #12, code = 0x1b (Configuration entry), length = 7
000: ff ff ff ff ff ff ff
Config index = 0x3f(default)
Interface byte = 0xff (reserved) BVD1/2 active, card WP active, +RDY/-BSY active, wait signal supported
Vcc pwr:
Nominal operating supply voltage: 9 x 100V, ext = 0xff, ext = 0xff, ext = 0x0
Minimum operating supply voltage: 1 x 10uV
Maximum operating supply voltage: 1 x 10uV
Continuous supply current: 1 x 10nA
Max current average over 1 second: 1 x 10nA
Max current average over 10 ms: 1 x 10nA
Power down supply current: 1 x 10nA
Reserved: 1 x 10nA
Vpp1 pwr:
Vpp2 pwr:
Wait scale Speed = Reserved x 1 ns
RDY/BSY scale Speed = Reserved x 1 ns
External scale Speed = 8.0 x 10 ms
Card provides address decode
IRQ modes:
IRQ level = 0
Memory descriptor 1
Max twin cards = 0
Misc attr:
Tuple #13, code = 0xff (Terminator), length = 0
2 slots found
_ ______________________________________________________________________
| / o / / _ Bulte email: wilko @ yedi.iaf.nl
|/|/ / / /( (_) Arnhem, The Netherlands WWW: http://www.tcja.nl
______________________________________________ Powered by FreeBSD __________
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199804301854.UAA25384>